Fedora Networking :: Getting RT2870 Setup On Fc11?
Jun 26, 2010
I've got a sitecom usb wireless adapter that uses the RT2870 chipset.I have got the rt2870sta module and have a ra0 interfaceI can set up a connection in the network tool and it recognises the usb device fine.
i don't have connection in my compuer write now so i whant to install RT2870 driver but i don't know how i found this tutorials [URL] but i can't install may be i have error in choise package this is my kernel version Linux Ouz3r4 2.6.35.10-74.fc14.i686 #1 SMP Thu Dec 23 16:17:40 UTC 2010 i686 i686 i386 GNU/Linux i found this driver too [URL] but how to install
my wireless adapter(WUSB600N) doesn't run when I log in. The driver is loaded on start-up but the green light is not on the adapter. I have to physically disconnect the adapter and plug it back in to get it recognised and it works fine afterwards
since the release of the 2.6.32.14-127 kernel a couple of days ago I can't use my wireless adapter (rt2870 based) since there isn't a kmod-rt2870 package released for this kernel.Normaly I found that the kmod package was available the same day as the kernel. Does anyone know why there is such a delay this time? Or if there is a workaround
I have recently installed Fedora 10 onto my PC, dual booting with XP, and I am fairly new to linux. I have been trying to connect to my wireless network, but cannot even get Fedora to recognise my wireless adapter (Belkin N1 +MIMO). I have tried to follow a few tutorials that go through either the ndiswrapper method or by using native drivers. Because I don't have an internet connection on Fedora, I have to boot into XP to download the files for either ndiswrapper or the native drivers, rather than installing using the terminal.I downloaded the ndiswrapper RPM, and it failed because of an 'unexpected error', and when using the tarball, it could not find the makefile. The native drivers did not install because of unresolved dependencies.
I am new to Fedora have not used it in many years. I have zero networking knowledge. I read several threads on getting the RT 2870 USB connection working. But had no joy after install the three rt2870 kmod items from RPMFusion and rebooting. get this first step in networking done right?
The problem is that when I connect my phone to my machine FC11 x64 via USB and use the phone as a modem NetworkManager does not recognise the phone as a modem. The phone works well on my laptop which is FC11 32bit system, NetworkManager detects it and sets it up as eth2 and away I go, no problems at all. I would like to ask the community how can I go fault finding to find out why it does not work. #lsusb shows that the modem is being detected by the system but beyond this I don't know where to look and get things going.
Since I installed FC11 vpnc stop working. I get "vpnc: no response from target." I tried running it with "strace" and the reason is a timeout: poll([{fd=3, events=POLLIN}], 1, 4000) = 0 (Timeout)
I tried google and adding "NAT Traversal Mode cisco-udp" to the config file works for some people but not for me Does anyone had experience with vpnc 0.5.3 in FC11?
Trying to set up a modem connection under FC11, using the applet under System/Administration/Network/Add gives the following error:
Code:
Local variables in innermost frame: If the script is faulty, could you guide me through setting it up by hand? I am required to be away from my normal location for a few weeks starting Monday and need to keep in touch.
I can't get my Broadcoam BCM4322 to connect to a protected access point. I've tried the drivers from rpmfusion, and tried to build the module with the source+binary package from Broadcom, all with no luck. The failure seems to happen during the WPA negotiation.
I haven't tried connecting to an unsecured WiFi access point.
When booting this same laptop to Kubuntu 9.04, it can connect to secured, so it is possible under linux.
Here's output from lspci, and the tail of the log while KNetworkManager is trying to connect the device.
I'm trying to install my pci wireless card that uses bcm4318 technology. I installed ndiswrapper and the driver for the card. However, I still can't seem to get wirelessworking. I'm not sure what info you will need to help me diagnose this problem. Here is the output of ndiswrapper -l:
I know theres a thread for this for fc9 but thats probably kind of outdated now. So I am trying to set up a wireless connection for a pc in my bedroom and just want something that will work out of the box.
On FC10, when system boots up, it would auto detect (from DHCP) and configure eth0.
This does not happen on FC11, but I can manually configure the interface. The entries in /etc/sysconfig/network-scripts/ifcfg-eth0 are identical on both OS releases.
Don't know if this is related, but when I run System->Administration->Bootloader, it fails system-config-boot - missing module kudzu.
I have a problem with Netgear Wireless WG311v3 card and it is not listed in "ifconfig -a". Network Manager does not see the Netgear card either, just eth0 the onboard wired NIC. Here is the result of lspci.
i want to ask a question. sometimes i use a gprs modem to connect to the net. the gprs modem uses the usb port. i've connected this pc to another machine through crossover cable. the problem is that when there are two active connections, firefox can't load anything. also how can i share the gprs modem with my other pc that is connected via crossover?
PS. in my active network connections it shows: eth0- the NIC and auto eth1 - the gprs modem
i have also tried to change the firefox preferences but to no avail.
Finally, my mobile broadband is native to Fedora. Just finished clean install of FC11 and it found the device, started it, and it works, just like it did in WIndows. ZeroConfig FTW! Great job Fedora team on this. FC10 it didn't work at all and FC6, 7, and 8 it took a lot of tinkering to make it fully functional.Also, NM is working MUCH better now with static IPs over the previous FC10 version. Set it up first run and had no issues with running my laptop on the network.
A few days ago (september 7) my wireless suddenly stopped working. I am using FC11, and have an Atheros AR5211 wireless card and have been using the ath5k driver with GNOME NetworkManager. Wireless networks are detected by NM perfectly fine. When I try to connect, the icon spins around those two dots, and one of them becomes green. If the network is wep protected, it asks for the password. After a while, it times out, regardless of the protection. I don't remember changing pretty much for the last two months, so I'm sort of surprised. I did download and install a kernal, along with an selinux-policy update.
If I run dmesg, relevant looking lines included:
ADDRCONF(NETDEV_UP): wlan0: link is not ready and a long series of these at the end: wlan0: direct probe to AP 00:0b:86:4f:8a:20 try 1 wlan0: direct probe to AP 00:0b:86:4f:8a:20 try 1
[code]....
Note: I previously posted this in "Laptops," but Networking seemed like a better place to do it.
I have a Broadcom wireless card in my hp dv6500z laptop, I had it all working properly in FC9 thanks to bbfuller and his post on the subject. After I upgraded to FC11 I have been unable to get it to connect.
I can see my neighbor's sites and suppose I could see my own if the SSID was allowed to broadcast but I keep that turned off. I put in all of the setting, including the network security key, but it won't connect, then when I go back and look again, the security key is not even close to what I put in; it gets changed to a huge string of characters.
I redownloaded broadcom-wl-4.150.10.5.tar.bz2.tar and followed the instruction on the post once again but no luck, which, after I thought about it, was a waste of time because if I can see other's wireless, then the card must be working. I have tried using Network Manager and not using Network Manager and still no luck...
I've compiled and installed my rt2870sta.ko and the firmware to the correct locations but my ubuntu 10.10 is loading the one under /lib/modules/2.6.38-25-generic/kernel/drivers/staging/rt2870/rt2870sta.ko. How do I get it to use the correct driver? I've attached a screenshot of the module info.
I have a Sparklan WUBR-502GN USB dongle with the RT2870 chip. It has worked, (with a little effort) of previous installs of 9.04, 9.10, 10.04 and 10.10. However it refuses to work in 11.04. I followed the same procedures, (blacklisting, confirming device ID, modifying config.mk and rt_linux.h, sudo make & make install and removing staging/rt2870), outlined in past forum articles and that worked in the previous RCs, but the connection to my home network will not complete. Has something changed in 11.04 that is substantially different from past releases?
P.S. the only thing I haven�t done, since 11.04 was only installed moments before, is do the build essential and headers.
I am very new to Ubuntu and if I could get internet I'm sure I would love it as it appears very speedy! I don't want to resort to reloading Windows just because of this!I've managed to install the RT2870.inf driver for my Belkin wireless adaptor but couldn't install the sys file. Hence my adaptor still won't work - well I think this is why but hoping someone can enlighten me step by step.
Alright yall, I just got my wireless usb device to work on ubuntu 10.10. I did alot of searching and I finally figured it out. this is what I did.
1.Download the linux drivers from this post, its called Ralink_RT3572USB_drv2400.zip
2.Extract them to a directory.
3.Make sure you have build-essential installed on your computer. you can do this by opening a terminal and typing Code: sudo apt-get install build-essential 4.Now install linux headers so that you can compile the drivers. Code: sudo apt-get install linux-headers-$(uname -r) 5.Now in your terminal goto where you extracted the Ralink_RT3572USB_drv2400 files. once in that directory type
I'm trying to install the rt2870 driver on my server running Ubuntu Server 8.04. I've installed build-essential, checkinstall, cvs, subversion, git-core, mercurial... After uncompressing the tarball, doing a "sudo make" gives me this output:
I tried getting a Belkin USB Wireless adapter:N150 to work in a fresh installation of 10.4 with no success. After reading several forum posts I tried both solutions with ndiswrapper and the XP driver and with the Ralink native driver with no luck.
Code: lsusb Bus 005 Device 008: ID 050d:935a Belkin Components Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
I have installed the Fedora 14, and a Dlink usb wireless adapter (DWA-125) with rt2870 chipset, but this one isn't working with my OS.
I typed the lsusb command
Code: Bus 001 Device 006: ID 07d1:3c0d D-Link System DWA-125 Wireless N 150 Adapter(rev.A1) [Ralink RT2870] I downloaded the drivers from YUM, the rt2870 and also kmod-rt2870. I thing that this step is ok.
I typed the dmesg | grep 2870 command
Code: [21421.956342] usbcore: registered new interface driver rt2870 When I open the /proc/modules file, it shows the line bellow rt2870sta 542230 0 - Live 0xffffffffa02fc000
I just installed the Fedora 12 live CD, but the driver for my EnGenius EUB 9801 (rt2870) USB WiFi adapter is not installed. I tried some of the suggestions found on this forum, but since I'm new at Linux I haven't yet been successful with installing the driver.
Does anyone know if the much larger DVD ISO already contains the driver built-in for the rt2870 for Fedora? If so I'm thinking it would be easier (for me) to just download the DVD ISO and re-install FC12 using that to get my WiFi USB adapter working.
I am using a Sparklan WUBR-505N abgn USB dual band stick for the wireless connection on one of my Fedora 12 laptops. I have an Apple Airport Extreme BaseStation that can advertise a 5GHz connection ie it broadcasts two sids... The network manger only see the 'regular' sid and the usb stick only connects in the 2.4GHZ frequencies. Does the rt2870 driver support the 5GHz frequencies? If so how can I force a 5GHz connection?
I seem to be missing some step(s) for getting an interface to appear in the output of ifconfig and iwconfig for a RT2870 wireless USB 802.11n adapter (made by Panda Wifi). Let me step you through what's I've done thus far.
After plugging the device in, it's low-level identification is as follows (see bold):
root@xps720# lsusb Bus 002 Device 002: ID 046d:0b06 Logitech, Inc. Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870 Wireless Adapter Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
