Fedora Networking :: Wireless Suddenly Stopped Working - FC11?
Sep 23, 2009
A few days ago (september 7) my wireless suddenly stopped working. I am using FC11, and have an Atheros AR5211 wireless card and have been using the ath5k driver with GNOME NetworkManager. Wireless networks are detected by NM perfectly fine. When I try to connect, the icon spins around those two dots, and one of them becomes green. If the network is wep protected, it asks for the password. After a while, it times out, regardless of the protection. I don't remember changing pretty much for the last two months, so I'm sort of surprised. I did download and install a kernal, along with an selinux-policy update.
If I run dmesg, relevant looking lines included:
ADDRCONF(NETDEV_UP): wlan0: link is not ready
and a long series of these at the end:
wlan0: direct probe to AP 00:0b:86:4f:8a:20 try 1
wlan0: direct probe to AP 00:0b:86:4f:8a:20 try 1
[code]....
Note: I previously posted this in "Laptops," but Networking seemed like a better place to do it.
View 14 Replies
ADVERTISEMENT
Jan 12, 2010
I have a Broadcom wireless card in my hp dv6500z laptop, I had it all working properly in FC9 thanks to bbfuller and his post on the subject. After I upgraded to FC11 I have been unable to get it to connect.
I can see my neighbor's sites and suppose I could see my own if the SSID was allowed to broadcast but I keep that turned off. I put in all of the setting, including the network security key, but it won't connect, then when I go back and look again, the security key is not even close to what I put in; it gets changed to a huge string of characters.
I redownloaded broadcom-wl-4.150.10.5.tar.bz2.tar and followed the instruction on the post once again but no luck, which, after I thought about it, was a waste of time because if I can see other's wireless, then the card must be working. I have tried using Network Manager and not using Network Manager and still no luck...
View 6 Replies
View Related
Jul 13, 2011
When originally installing 11.04 I had problems getting my Ralink 5390 wireless card to work.
Today my computer froze completely and I had to turn it off via the power switch. When I turned it back on, wireless was no longer recognized! My iPod can connect to the network just fine, so it must be an Ubuntu problem. There are no problems with my ethernet connection either.
I researched this and found several threads about blocking and unblocking wireless devices using the rfkill command. Well, unfortunately for me the rfkill command doesn't work. When I type sudo rfkill list or sudo rfkill unblock all, nothing happens; it just returns me to my bash prompt. I even tried uninstalling and reinstalling rfkill...nothing.
View 1 Replies
View Related
Jul 24, 2010
I'm using Ubuntu 10.04. I was happily connected to internet and surfing some forum, when wireless connection suddenly stopped working.
Now I can't find any access point, and I'm pretty sure I didn't do anything to justify this behaviour.
It already happened a month ago, but I had to format my drive, so I didn't really bother to try to solve the problem.
Anyway. I'm posting here the results of the commands I think I can help with a diagnosis; if something else is needed.
I'm using a different computer to post this thread, so I'm manually writing the output.
Code:
sudo iwconfig wlan0
wlan 0 IEEE 802.11bg ESSID: off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
sudo iwlist wlan0 scan
wlan0 No scan results
View 2 Replies
View Related
Apr 18, 2011
I'm running a gateway lapbook w/10.04 LTS and an etheros wirless card. Card has been working fine for almost a year - from cold boot, warm boot, and recovery from standy (shut lid, open, press power button). I was fiddling with setting a static IP for the wirelss card by modifying the interfaces text file. I made some changes, and restored the file to its original contents after some noodling around. Wireless still worked fine after that. Last night I took the laptop out of suspend as usual - lifted lid, pressed power button - but the wireless indicator remained grayed out and I haven't been able to reenable wireless connectivity since. ifconfig shows the wireless card is there, and cabling the e-net port directly to my hub works fine.
View 3 Replies
View Related
Oct 14, 2010
I have an HP a670y desktop computer using the included wireless antenna (looks like a big Sorry game piece). I am running Ubuntu 10.04 x64 dual booted with Windows Vista x64. I haven't had internet for a while but just got it today and decided to do some updating in both Windows and Ubuntu. It had detected my router and I copied and pasted the WEP key then it asked for my password, but my keyboard wasn't connected so I clicked cancel for the password window and it connected anyway.
I opened the Synaptic package manager and started downloading some updates while I did some browsing on the internet. I had restarted my computer when the updates were done and it asked again for my WEP key. I copied and pasted just as I did before and entered my password and after it tried to connect it asked for my password again. I thought maybe the internet was down so I decided to boot up Windows and it connected right away. I wonder if one of my updates messed something up. Has anyone else had this happen?
View 1 Replies
View Related
Feb 9, 2009
I have an HP Pavilion notebook with a Broadcom WLANcard that had been working very nicely in Fedora Core 10 until this evening, when I took my notebook to a conference room where there was no internet access. (I tried to connect to wireless networks, but there were none in the area, as I discovered.) am now unable to connect to my local (home) wireless network as the device is now non-existent . Can someone please walk me through the steps to fix this or re-install it (I have tried reinstalling broadcom-wl, but that didn't help). My lspci listing is reproduced below:
Code:
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
[code]...
View 10 Replies
View Related
Aug 4, 2009
my eth0 suddenly stopped working on FC10. i have been using it the whole time, and now it refuses to even ping the gateway. dhclient is not receiving a dhcp offer and when i put in the information manually, it is not even able to ping the gateway. netstat -rn shows that the destination of the router is going nowhere.
i do not think it is the hardware/software, but rather maybe the provider? i am from central europe but just moved up to great britain and working at a friends place. i can connect the mac powerbook without a problem (it will get an ip with dhcp), but not the linux machine.it is a normal ethernet modem connection here. can it be, that it checks MAC addresses or even the computer names? the powerbook also has a really weired IP address: 77.102.xxxxx
i am not using network manager, but command line tools and have nm uninstalled. does anyone have a clue, what this could be about? i am not a newbie, but this is really puzzling me.....
View 4 Replies
View Related
Nov 19, 2010
A couple days ago I booted up my Ubuntu 10.10 machine as usual,but the wired LAN connection did not work; it doesn't seem to see any wired connection devices. I can still connect to a wireless network with no problem, and if I plug that same ethernetable into another machine it works fine. I've been happily using this setup for weeks; the LAN only stopped working a day or two ago. So I figure there's two possibilities:A recent update caused NetworkManager to stop working with wired LAN connections, but I'm e only persothed affected (unlikely)My motherboard's ethernet port died (this motherboard only a couple weeks old, so this also seems unlikely)I'm not good at diagnosing problems with networking, so who can tell me where to st
View 9 Replies
View Related
Nov 11, 2010
I switched my FC11 system off yesterday. Turning it on this morning, NO domain names can be resolved anymore.I can ping IP adresses directly, and even get to them in FireFox if I type the IP address. However, typing any domain name at all fails. I cannot ping or SSH to any domain name, but as soon as I enter an IP, it works. I can ping the DNS server by IP that is set in my /etc/resolv.confI checked on an XP system using the same DNS server set in /etc/resolv.conf (which can also be pinged on IP from my FC11 system), on the same connection from the same ISP, and it works.E. g. without touching anything at all (and all updates are turned off) my FC11 system has stopped resolving domain names.I'm running 32bit FC11. The system has been working fine for more than 2 years.So it has spontaneously stopped doing DNS when I enter a domain name. Where can I start looking?
View 1 Replies
View Related
Aug 13, 2009
I'm trying to install my pci wireless card that uses bcm4318 technology. I installed ndiswrapper and the driver for the card. However, I still can't seem to get wirelessworking. I'm not sure what info you will need to help me diagnose this problem. Here is the output of ndiswrapper -l:
rt2860: driver installed
View 4 Replies
View Related
Sep 17, 2009
i did an update yesterday and after me-tv doesn't work any more, now when i run me-tv i get this error message,Duplicate object id 'hbox1' on line 1220 (previously on line 535)To c if the tunner was working i installed kaffeine and it works fine, so its something related to the me-tv, any ideas how to fix it
View 1 Replies
View Related
Oct 13, 2010
I've started to set up a server at my house, where I eventually want to run it headless, and I can just VNC in from my other Desktop. I installed Ubuntu 10.10, setup remote desktop on the server, and from there was able to do any work remotely. That was nice. I turn the computer off at night, and the next day when I was going to work on it, I cannot VNC in anymore. One day passed, and now every time I try to use VNC it comes up with "Failed to connect to server" I also set a static IP address on the server too, so I know the address isn't changing every so often.
View 1 Replies
View Related
May 26, 2010
Hope this saves some1 an immense amount of time;First type this;
Code:
rfkill list
check if the problem looks like this
[code]....
View 2 Replies
View Related
Dec 28, 2010
Only been using linux for about 2 weeks now. Yesterday my internet worked without a hitch now today all of a sudden it wont connect. I had the "Install problem! The configurataion defaults for gnome manager have not been installed correctly" so I deleted my music directory and now it boots fine, dont know if that might be part of the issue/ I dual boot win7 and i can get wireless on that partition but not ubuntu
View 9 Replies
View Related
Aug 12, 2010
Version: Ubuntu 10.04 Relavant hardware: P5QL Pro built-in ethernet, cable modem with linksys wireless-G router (although problem is with ethernet connection, not wireless)
One minute my ethernet was working, and the next it stopped working. The only thing that I did between it working and not working was install electricsheep from Synaptic and then I shut down the computer. When I restarted a bit later, no ethernet connection shows up.
I checked the cables, made sure they are in tight.
My laptop connects using the same ethernet cable fine. So its not the cable or the router.
I reset the router and the computer at the same time. Still doesn't work.
I don't know where to even start with troubleshooting this sort of problem. Everything to the extent of my computer knowledge seems to be working fine.
View 3 Replies
View Related
Jul 4, 2010
I installed Ubuntu 10.4 side by side with my Vista. This is on a PC I leave on permanently and use as a sort of Sever, so Security and Network connection are VERY important on this device. I use it for documents and IP PBX (telephone system). I currently use Vista and 3CX, but I plan to roll it over to Unbuntu full time once its up and runnng correctly - I will just need to change the Grub2 conf priority. After install, all was fine and I managed to make many changes to settings, apps and updates, but I have noticed in the past week when going in to make further changes the network has suddenly stopped working! According to Network Manager and the icon on the panel it is connected and I can not see anything obvious that is not correct. I tried doing a PING (192.168.1.1) from Network Manager to the main router, but it failed. I know that there is nothing wrong with the network nor the card or PC it all sits on. It's working now with Vista and my other machines. It must be a config some-where.
View 9 Replies
View Related
Jun 11, 2010
Finally got around to dual-booting and all was going well. I was surprised to see that the webcam on my Vaio worked straight away. However, some time between one boot and another the webcam mysteriously stopped working..
Here is the last time it worked:
Jun 6 23:12:51 dillinga kernel: uvcvideo: Found UVC 1.00 device <unnamed> (05ca:1837)
Jun 6 23:12:51 dillinga kernel: input: UVC Camera (05ca:1837) as /devices/pci0000:00/0000:00:1a.7/usb1/1-2/1-2:1.0/input/input12
Then the next boot:
Jun 6 23:41:48 dillinga kernel: uvcvideo: Found UVC 1.00 device <unnamed> (05ca:1837)
Jun 6 23:41:48 dillinga kernel: uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
Jun 6 23:41:48 dillinga kernel: uvcvideo: Failed to query (129) UVC probe control : -32 (exp. 26).
[code]....
So I decided to boot into windows and make sure all was OK - and it was. Then I came back into Fedora and suddenly the camera was working again! I thought I'd reboot just to see if anything changed and alas here I am again with no webcam and the same error.
View 8 Replies
View Related
Nov 25, 2010
Right so yesterday my internet worked fine. Today - no connection at all. The light for my cable on the router doesn't even show up. I originally had indicator-network installed, so when the internet first stopped working, I tried a few other options such as tethering to my phone via usb and bluetooth (which I have successfully used in the past). However, these didn't work, and I figured that as connman is still in beta, maybe that was why. So I reinstalled network-manager and network-manager-gnome via a usb stick, uninstalled indicator-network, and rebooted the computer. Still no internet.
When I click on the applet, it says "No network devices are available". This is odd, as I definitely have a network device... it is part of the motherboard. So I thought I'd do the SMARTlan test or whatever it's called. It's part of my BIOS, so I ran that and it returned results that I (kinda) expected: when the cable wasn't plugged in, it returned one set of results. When it was only plugged into my computer (and not the router), it returned another set of results. And when it was plugged into both my computer and the router, it returned a third set of results. So that leads me to believe the cable itself is fine.
And when I move the cable to a different port on the router, nothing changes. The corresponding light still doesn't come on. Network-manager, telling there are no network devices. The BIOS can see the ethernet port and the cable. And the router is functioning perfectly for my parents' computer and my ps3. And I have checked the cable to my computer for physical damage - it follows the same path as the one to my ps3, and on top of that, nothing physical can possibly have happened to it in the last day. This happened once before, except I don't think the network devices were lost.
View 2 Replies
View Related
Apr 8, 2011
my Internet connection stopped working suddenly after updating the packages using synaptec package manager and rebooting it..can anyone say me why did this happen.BTW,mine is ubuntu 10.10 and i am absolute new to linux.I had to configure my n/w connections right from the scrap again
View 2 Replies
View Related
Feb 7, 2011
I've been running Ubuntu 10.10 on this ThinkPad for a couple of months now, with absolutely no problems at all.The wireless was working fine earlier today out at a coffee shop. When I got home and turned the computer on, the network applet just showed a "Wireless is disabled" message.I poked around for a while, mucking with whatever I could (limited, unfortunately, I don't have great linux-fu) and doing the ritual reboot to see if that would get things going.I then spent some time reading through forum threads here, but didn't find any answers.Below are the results of the various commands as described in HOWTO post a Wireless issue (ticket) sticky threadMachine brand and model
Code:
Lenovo ThinkPad T60p
lspci -nn | grep Atheros
[code]....
View 2 Replies
View Related
Mar 18, 2010
I am having problem with wireless networking my fedora 12 since i opened network manager yesterday. But to my notice i haven't done any changes. But still i am not able find any reason for the wireless network not to work. When i try to restart the network servies it gives the following msg.
Quote:
Bringing up interface eth0:
This version of ISC DHCP is based on the release available on ftp.isc.org. Features have been added and other changes have been made to the base software release in order to make it work better with this distribution.
Please report for this software via the Red Hat Bugzilla site: [url]
Did i do something wrong with the network manager or did something go wrong with fedora.
View 2 Replies
View Related
Sep 17, 2009
I have a wireless router at home, but I usually have my laptop connected to it through an ethernet cable. It had always worked with no problems until some time last week when the wired network stopped working (but the wireless still works with no problem). At first I thought that it was some update, but no. My laptop works ok with the wired network at my office, and I also tried a different laptop at home and it didn't work. It's not the cable either, I tried a different one. I haven't changed any settings in my router.So I really don't know what's going on. I just find it weird that the router's wired networking suddenly stops working but the wireless still works fine...
View 1 Replies
View Related
Jan 9, 2010
I have a relatively new F12 install (one week old) on which I got my wireless Broadcom card working using kmod-wl-PAE. It was a very easy process - not really a process just yum install kmod-wl-PAE.
After a few updates, I notice that the wireless card stopped working. I assumed maybe there was an update that conflicted, so I did a reinstall of kmod-wl-PAE and it worked again immediately.
Then I started installing compiz-fusion. Immediately after, wireless is broken again. So I yum erase kmod-wl-PAE and then yum install kmod-wl-PAE and it works again.
Now, only slightly later that same day, wireless stops working more or less randomly and I cannot get the reinstall of kmod-wl-PAE to fix it. So I uninstall, disable compiz-fusion, shut down, and restart the computer to try again. My thought is that maybe along the way my autostart compiz or something about compiz is causing the wireless not to configure properly. When I restart, wireless is working. Without kmod-wl-PAE installed:
yum info kmod-wl-PaE
Loaded plugins: presto, refresh-packagekit
Available Packages
Name : kmod-wl-PAE
Arch : i686
[Code].....
One, how is this even possible, and two, what is going on with the wireless working, not working, working, not working?
View 14 Replies
View Related
Mar 7, 2010
have a gateway nv78 laptop. I just ran the latest update on Fedora 12, and after Fedora stopped seeing wireless networks all together.
View 8 Replies
View Related
Apr 13, 2010
I have updated FC 11 on my hp 6730b laptop as $ su -c 'yum -y update'after updating I logged to kernel '2.6.30.10-105.2.23.fc11.i686.PAE', but my wireless is notworking any idea how to solve it. I have to solve it offline since I have only wireless internet at my work.
View 5 Replies
View Related
Apr 21, 2011
I've been running Ubuntu 10.10 (Maverick) x64 quite happily on my Dell e6500 for the past few months until today when I woke the computer up from sleep mode and could not use the wireless. The network-manager applet simply has 'Wireless' greyed out. I tried rebooting, thinking it was an issue with the wireless card not re-powering on properly after sleep, but to no avail. how to begin here?
View 5 Replies
View Related
Feb 8, 2010
i'm running Kubuntu karmic and i've been using a 3G Huawei E1552 modem to connect to the internet, everything was going well when suddenly my modem stopped working. I've tried reconfiguring everything, i even reinstalled kubuntu from scratch with no success.Here's a part of my /var/log/debug
HTML Code:
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099883] usb-storage: device found at 7
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099888] usb-storage: waiting for device to
[code].....
View 4 Replies
View Related
Mar 21, 2010
I am running Karmic on a Compaq Presario V3000 and this morning my wireless card is not being detected by Ubuntu's NetworkManager. I have no idea what caused this... literally, it was working when I shutdown my laptop last night. When I right-click the NetworkManager icon in the panel it does not show "Enable Wireless" (only "Enable Networking"). When I run ifconfig in terminal it shows my wireless card as being there (UP Broadcast Multicast). One weird thing - on the front of the laptop there is an LED which lights up blue when the card is working (ie normally), but right now it is orange (ie, if you flick the switch on the front of the laptop to toggle the wifi on or off... I have toggled it back and forth but nothing changes!)
View 1 Replies
View Related
Jan 14, 2011
I have been using ubuntu troublefree for some month, but yesterday, suddenly the wireless internet connection stopped working. It happened after i used the turn off wireless network shortcut, now i cant turn it on again (usually this works fine).The situation is now, that when i click on the tray icon showing connection it says, wired network disconnected (it never said this before), then if i click on the wireless shortcut it also says wireless disconnected... But if i click again it doesnt show connections, the disconnected sign just disappears...?
View 7 Replies
View Related
