Since I installed FC11 vpnc stop working. I get "vpnc: no response from target." I tried running it with "strace" and the reason is a timeout: poll([{fd=3, events=POLLIN}], 1, 4000) = 0 (Timeout)
I tried google and adding "NAT Traversal Mode cisco-udp" to the config file works for some people but not for me Does anyone had experience with vpnc 0.5.3 in FC11?
how nobody else could have run into this in the meantime. [URL] Two friends of mine are having the same issue on Ubuntu-11.4-machines. In short: Connecting to the Cisco-VPN via shell-command "vpnc" works flawlessly, whereas NetworkManager just doesn't connect at all. We had this working in older versions of Fedora/Ubuntu about some months ago...
View 9 Replies View RelatedIn fc10 & fc11 everything worked well with vpnc.
With fc12 vpnc starts allows me to connect to my work site then everything works fine til I try and start a remote desktop connections to a windows client use tsclient. All I get is a blackscreen and my laptop is hung.
At work without the vpnc it works fine if I start the vpnc from nm it performs the exact same way and I get the blackscreen.
I have disable selinux.I also disabled the firewall
there was another gentlemen on here with the same issue.
The only way out is a hard reboot and there are no messages in the logs that say there were any problems.
I am using KNetworkmanager-vpnc to VPN back to the office from home, the vpn connection works fine - for 15 minutes then I am disconnected. I am fairly certain that this is related to the Phase 1 key lifetime limit. The Knetworkmanager-vpnc GUI does not provide a location to enter this information. I think I found the config file that holds the connection information at /home/<user>/.kde/share/apps/networkmanagement/connections/ I just don't know the proper syntax to put in the file to specify a key life limit. Anyone out there know how to do this? I am using Fedora 14 x64 with knetworkmanager-vpnc 1.0.9-0.28.
View 1 Replies View RelatedI've been trying to connect to my office Cisco VPN several time using the network-manager-vpnc GUI in Ubuntu Karmic with no success. I read a couple of articles and i tried using the direct command line way:
Code:
sudo vpnc office
with the following /etc/vpnc/office.conf file:This is fictional data
Code:
IPSec gateway vpn.office.com
IPSec ID office
IPSec secret 0ff1c3
which worked perfecly.
So i went back to the Network Manager GUI way and i used the same credentials. Same fictional data I got a libnotify message telling me it couldn't connect.Anyone know how i could troubleshoot this issue? Would be great to have it integrated in gnome instead of running a background command which is not tracked by nwm.
I recently installed Fedora 15 x86_64 on my new AMD Machine and I'm quite pleased with things thus far.Here's where my problem comes. I mainly bought that machine to help me with Development. More specifically, Virtual Machines for testing purposes. I have installed Fedora 15 x86_64 as a qemu-kvm Virtual Machine and it's working.. for the most part. I am having a whole lot of trouble getting it to connect to the Internet.
My guess is the only way I'm going to reliably do that is to setup a Bridge. Yes/no? However, in order to setup a Bridge I need to disable NetworkManager and that where the fun happens. It completely disables my network connection. I'm probably missing something small, but I can't figure out what I'm missing. I've double checked my ifcfg-em1 multiple times(I've been trying for ~24 hours so far) and all the settings are as they should be.
I've turned NetworkManager off and stopped it(chkconfig and service) and turned network on(chkconfig and service). Theoretically I should simply need to turn off NM and turn on network and things should be fine. no?
Well, aside from adding:
ONBOOT=yes
NM_CONTROLED=no
to ifcfg-em1.
On my PC (fresh FC11 i386 instllataion from CDs), dhclient doesn't work. When it tries to get an IP address with dhclient, it gets No DHCPOFFERS reveived and fails. The ethernet of my PC works fine - I can manually set IP address, netmask, gateway etc. to connect to my persoal Linksys router, but if I change to DHCP, it fails as above. So it's not the problem of the ethernet driver of FC11. I suspect that dhclient of FC11 is buggy. (For the record, DHCP works fine on FC10 and Windows XP with my Linksys router.)
View 1 Replies View RelatedI have a couple VPNs I use for work, and after installing F14 x86_64 it is failing:
Code:
Nov 5 12:40:57 raykj NetworkManager[4106]: <info> VPN service 'vpnc' started (org.freedesktop.NetworkManager.vpnc), PID 4203
Nov 5 12:40:57 raykj NetworkManager[4106]: <info> VPN service 'vpnc' appeared; activating connections
[Code]....
I have been trying to connect to my University's VPN Server and for some reason vpnc fails. I have configured the vpn settings the same way I did for the past two years. They worked properly on Fedora 12 and 13, but for some reason fails on Fedora 14.
Code:
Jan 6 16:45:20 exodusprime NetworkManager[1269]: <info> Starting VPN service 'vpnc'...
Jan 6 16:45:20 exodusprime NetworkManager[1269]: <info> VPN service 'vpnc' started (org.freedesktop.NetworkManager.vpnc), PID 11731
Jan 6 16:45:20 exodusprime NetworkManager[1269]: <info> VPN service 'vpnc' appeared; activating connections
Jan 6 16:45:21 exodusprime NetworkManager[1269]: <info> VPN plugin state changed: 3
Jan 6 16:45:21 exodusprime NetworkManager[1269]: <info> VPN connection 'Swinburne University VPN' (Connect) reply received.
code....
Problem with fedora 13, I am no longer able set up a virtual private network using vpn. The following error message appers:
"/usr/sbin/vpnc: no response from target"
No problem when connecting with ubuntu or windows.
My intel pro wireless 2200 NIC doesn't work anymore. Yesterday it did, but not today (I didn't do anything special, so that it could go wrong).What is ucode and -62? Any ideas? I already checked the forums and found that ipw doesn't work when ndiswrapper is loaded. Well, I don't have it loaded. What happend?
View 8 Replies View RelatedI am having problems accessing my work desktop through my home computer running Fedora 13. I am able to remote into work through MAC and Windows XP. I loaded vpnc and was able to connect to the concentrator. I also able to ping it too. I cannot connect to my desktop using rdesktop. I get error message �Unable to connect, socket is unavailable. I cannot ping to the desktop.
View 2 Replies View RelatedI am having difficulties in establishing a vpn connection using vpnc (or NetworkManaager-vpnc).
As long as the openswan IPsec daemon is running, vpnc-helper quits with the error message
Quote:
Failed to bind to 0.0.0.0:500: Address already in use
[user@computer ...]# vpnc-helper --local--port 0
If I use NetworkManager-vpnc, then establishing the connection simply fails.
Using the --local-port 0 option does not change anything.
If I stop the ipsec service (service ipsec stop) then establishing the connectiong works, both with NetworkManager-vpnc and the console tool, but apparently the network traffic is not routed via the VPN - in my case this means that I cannot access hosts within the vpn and stuff.
Funny thing is - on my notebook from where I connect via WLAN, everything works fine. With Fedora 13 everything works fine, too.
Does anybody have an idea how to enforce that the vpn connection is actually used?
I've been using fedora for about 2 years, and i recently bought a new laptop. After using a usb mouse my toughpad no longer works? Now it works on login but after login touchpad input is gone.
View 4 Replies View RelatedI've installed kmod-nvidia on my F12 system and now it doesn't boot anymore. I just receive a black screen with a blinking '_' on top of my screen immediately after i choose F12 in my grub menu. (I have a Nvidia 8800GT.)
I've tried to run the following command after the installation but it didn't work: [url]
mv /boot/initramfs-$(uname -r).img /boot/initramfs-$(uname -r)-nouveau.img
So I didn't blacklist nouveau or anything else. I just foolishly thought it was going to work.
Now I can't boot my system anymore. Is there any way to solve the problem? Or can I remove kmod-nvidia using a live cd? How?
The problem is that when I connect my phone to my machine FC11 x64 via USB and use the phone as a modem NetworkManager does not recognise the phone as a modem. The phone works well on my laptop which is FC11 32bit system, NetworkManager detects it and sets it up as eth2 and away I go, no problems at all. I would like to ask the community how can I go fault finding to find out why it does not work. #lsusb shows that the modem is being detected by the system but beyond this I don't know where to look and get things going.
View 1 Replies View RelatedI've got a sitecom usb wireless adapter that uses the RT2870 chipset.I have got the rt2870sta module and have a ra0 interfaceI can set up a connection in the network tool and it recognises the usb device fine.
[root@genie devices]# iwconfig
ra0 RT2870 Wireless ESSID:"******" Nickname:"RT2870STA"
Mode:Auto Frequency=2.462 GHz Access Point: Not-Associated
Link Quality=10/100 Signal level:0 dBm Noise level:-97 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
I have no control over it and the wireless bit in Network Manager is greyed out. I got the firmware from the Ralink site
/lib/firmware/rt2870.bin
I have set the country code in the .dat file to 1 for channels 1-13 and selected channel 11 My netgear wg-614 wireless light has no activity.
I'm having problems with vpnc on F12 that work fine on F10 and F11. On F12, I can connect and can do some activities, but so far I noticed the following (show-stopping) issues:Attempting to connect to an Oracle database using either sqlplus or TORa hangs and eventually times out. I tried both the 11G and 10G instant clients.Copying a file to the host via a smb:// mount in nautilus freezes. An empty file is created though.
A rdesktop client opens a "black" window and goes no further. I attempted to downgrade vpnc on my F12 workstation from vpnc-0.5.3-4.fc12.x86_64 to vpnc-0.5.3-3.fc11.x86_64 to no avail. I also downgraded libgcrypt too and this didn't help either. Moreover, I upgraded these to the F13 rawhide version - still no luck.
I also confirmed on a F11 virtual machine that these work and that it doesn't work on 2 x64 and 1 x386 F12 machines. (The configuration and the host are the same in all cases.)
Fresh install of FC11. Had to install libwvstreams-4.5.1-5.fc11.i586.rpm and wvdial-1.60-8.fc11.i586.rpm
Now get following error -
Probably there is bug in kernel used FC11 [url] This bug freeze computer after ping or other data sending over VPN connection.
Is there any chance to backport this patch to kernel in FC11?
More about this in topic:[url]
Trying to set up a modem connection under FC11, using the applet under System/Administration/Network/Add gives the following error:
Code:
Local variables in innermost frame: If the script is faulty, could you guide me through setting it up by hand? I am required to be away from my normal location for a few weeks starting Monday and need to keep in touch.
I can't get my Broadcoam BCM4322 to connect to a protected access point. I've tried the drivers from rpmfusion, and tried to build the module with the source+binary package from Broadcom, all with no luck. The failure seems to happen during the WPA negotiation.
I haven't tried connecting to an unsecured WiFi access point.
When booting this same laptop to Kubuntu 9.04, it can connect to secured, so it is possible under linux.
Here's output from lspci, and the tail of the log while KNetworkManager is trying to connect the device.
lspci | grep -i network
00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03)
0c:00.0 Network controller: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller (rev 01)
[Code]....
I'm trying to install my pci wireless card that uses bcm4318 technology. I installed ndiswrapper and the driver for the card. However, I still can't seem to get wirelessworking. I'm not sure what info you will need to help me diagnose this problem. Here is the output of ndiswrapper -l:
rt2860: driver installed
I know theres a thread for this for fc9 but thats probably kind of outdated now. So I am trying to set up a wireless connection for a pc in my bedroom and just want something that will work out of the box.
View 2 Replies View RelatedOn FC10, when system boots up, it would auto detect (from DHCP) and configure eth0.
This does not happen on FC11, but I can manually configure the interface. The entries in /etc/sysconfig/network-scripts/ifcfg-eth0 are identical on both OS releases.
Don't know if this is related, but when I run System->Administration->Bootloader, it fails system-config-boot - missing module kudzu.
I have a problem with Netgear Wireless WG311v3 card and it is not listed in "ifconfig -a". Network Manager does not see the Netgear card either, just eth0 the onboard wired NIC. Here is the result of lspci.
Code:
[root@mylinux ~]# lspci -nn
02:00.0 Ethernet controller [0200]: Attansic Technology Corp. Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller [1969:1026] (rev b0)
03:00.0 IDE interface [0101]: Marvell Technology Group Ltd. 88SE6101 single-port PATA133 interface [11ab:6101] (rev b2)
[Code]......
i want to ask a question. sometimes i use a gprs modem to connect to the net. the gprs modem uses the usb port. i've connected this pc to another machine through crossover cable. the problem is that when there are two active connections, firefox can't load anything. also how can i share the gprs modem with my other pc that is connected via crossover?
PS. in my active network connections it shows:
eth0- the NIC
and auto eth1 - the gprs modem
i have also tried to change the firefox preferences but to no avail.
Both my computers run on FC11.
Finally, my mobile broadband is native to Fedora. Just finished clean install of FC11 and it found the device, started it, and it works, just like it did in WIndows. ZeroConfig FTW! Great job Fedora team on this. FC10 it didn't work at all and FC6, 7, and 8 it took a lot of tinkering to make it fully functional.Also, NM is working MUCH better now with static IPs over the previous FC10 version. Set it up first run and had no issues with running my laptop on the network.
View 6 Replies View RelatedA few days ago (september 7) my wireless suddenly stopped working. I am using FC11, and have an Atheros AR5211 wireless card and have been using the ath5k driver with GNOME NetworkManager. Wireless networks are detected by NM perfectly fine. When I try to connect, the icon spins around those two dots, and one of them becomes green. If the network is wep protected, it asks for the password. After a while, it times out, regardless of the protection. I don't remember changing pretty much for the last two months, so I'm sort of surprised. I did download and install a kernal, along with an selinux-policy update.
If I run dmesg, relevant looking lines included:
ADDRCONF(NETDEV_UP): wlan0: link is not ready
and a long series of these at the end:
wlan0: direct probe to AP 00:0b:86:4f:8a:20 try 1
wlan0: direct probe to AP 00:0b:86:4f:8a:20 try 1
[code]....
Note: I previously posted this in "Laptops," but Networking seemed like a better place to do it.
I have a Broadcom wireless card in my hp dv6500z laptop, I had it all working properly in FC9 thanks to bbfuller and his post on the subject. After I upgraded to FC11 I have been unable to get it to connect.
I can see my neighbor's sites and suppose I could see my own if the SSID was allowed to broadcast but I keep that turned off. I put in all of the setting, including the network security key, but it won't connect, then when I go back and look again, the security key is not even close to what I put in; it gets changed to a huge string of characters.
I redownloaded broadcom-wl-4.150.10.5.tar.bz2.tar and followed the instruction on the post once again but no luck, which, after I thought about it, was a waste of time because if I can see other's wireless, then the card must be working. I have tried using Network Manager and not using Network Manager and still no luck...