Fedora Networking :: Wireless Stopped Working After Upgrade To FC11?
Jan 12, 2010
I have a Broadcom wireless card in my hp dv6500z laptop, I had it all working properly in FC9 thanks to bbfuller and his post on the subject. After I upgraded to FC11 I have been unable to get it to connect.
I can see my neighbor's sites and suppose I could see my own if the SSID was allowed to broadcast but I keep that turned off. I put in all of the setting, including the network security key, but it won't connect, then when I go back and look again, the security key is not even close to what I put in; it gets changed to a huge string of characters.
I redownloaded broadcom-wl-4.150.10.5.tar.bz2.tar and followed the instruction on the post once again but no luck, which, after I thought about it, was a waste of time because if I can see other's wireless, then the card must be working. I have tried using Network Manager and not using Network Manager and still no luck...
A few days ago (september 7) my wireless suddenly stopped working. I am using FC11, and have an Atheros AR5211 wireless card and have been using the ath5k driver with GNOME NetworkManager. Wireless networks are detected by NM perfectly fine. When I try to connect, the icon spins around those two dots, and one of them becomes green. If the network is wep protected, it asks for the password. After a while, it times out, regardless of the protection. I don't remember changing pretty much for the last two months, so I'm sort of surprised. I did download and install a kernal, along with an selinux-policy update.
If I run dmesg, relevant looking lines included:
ADDRCONF(NETDEV_UP): wlan0: link is not ready and a long series of these at the end: wlan0: direct probe to AP 00:0b:86:4f:8a:20 try 1 wlan0: direct probe to AP 00:0b:86:4f:8a:20 try 1
[code]....
Note: I previously posted this in "Laptops," but Networking seemed like a better place to do it.
I switched my FC11 system off yesterday. Turning it on this morning, NO domain names can be resolved anymore.I can ping IP adresses directly, and even get to them in FireFox if I type the IP address. However, typing any domain name at all fails. I cannot ping or SSH to any domain name, but as soon as I enter an IP, it works. I can ping the DNS server by IP that is set in my /etc/resolv.confI checked on an XP system using the same DNS server set in /etc/resolv.conf (which can also be pinged on IP from my FC11 system), on the same connection from the same ISP, and it works.E. g. without touching anything at all (and all updates are turned off) my FC11 system has stopped resolving domain names.I'm running 32bit FC11. The system has been working fine for more than 2 years.So it has spontaneously stopped doing DNS when I enter a domain name. Where can I start looking?
Like many others it seems, my wireless has stopped working since a recent upgrade The answer does not lie in analysis of logs, settings etc. but surely with those who did it - they should provide a fix. I cannot believe everyone expects each individual users to go into their own analysis of why this is no longer working as it is clearly widespread. I have been using Ubuntu for 18 months without this problem on the same dual-boot laptop, and it still works on Windows as before, only Ubuntu 10.4 has recently stopped my network card from working.
I need to know when this will be fixed. I have been embarrassed by promoting Ubuntu to many colleagues who now also cannot work at home on their wireless networks. Seriously disillusioned I may start looking for a more stable alternative to Windows.
I'm trying to install my pci wireless card that uses bcm4318 technology. I installed ndiswrapper and the driver for the card. However, I still can't seem to get wirelessworking. I'm not sure what info you will need to help me diagnose this problem. Here is the output of ndiswrapper -l:
i did an update yesterday and after me-tv doesn't work any more, now when i run me-tv i get this error message,Duplicate object id 'hbox1' on line 1220 (previously on line 535)To c if the tunner was working i installed kaffeine and it works fine, so its something related to the me-tv, any ideas how to fix it
I am having problem with wireless networking my fedora 12 since i opened network manager yesterday. But to my notice i haven't done any changes. But still i am not able find any reason for the wireless network not to work. When i try to restart the network servies it gives the following msg.
Quote:
Bringing up interface eth0:
This version of ISC DHCP is based on the release available on ftp.isc.org. Features have been added and other changes have been made to the base software release in order to make it work better with this distribution.
Please report for this software via the Red Hat Bugzilla site: [url]
Did i do something wrong with the network manager or did something go wrong with fedora.
I am running Fedora 14. I've had an ASUS wireless adapter working for a few months now, with no problems. Today, I installed updates, one of which required a computer reboot (not just logging out and back in). I rebooted the computer, and when it came back up, the wireless adapter did not work.The adapter is visible after lsusb, but there is no wireless showing after iwconfig. What happened? How do I fix it?
I have a wireless router at home, but I usually have my laptop connected to it through an ethernet cable. It had always worked with no problems until some time last week when the wired network stopped working (but the wireless still works with no problem). At first I thought that it was some update, but no. My laptop works ok with the wired network at my office, and I also tried a different laptop at home and it didn't work. It's not the cable either, I tried a different one. I haven't changed any settings in my router.So I really don't know what's going on. I just find it weird that the router's wired networking suddenly stops working but the wireless still works fine...
I have a relatively new F12 install (one week old) on which I got my wireless Broadcom card working using kmod-wl-PAE. It was a very easy process - not really a process just yum install kmod-wl-PAE.
After a few updates, I notice that the wireless card stopped working. I assumed maybe there was an update that conflicted, so I did a reinstall of kmod-wl-PAE and it worked again immediately.
Then I started installing compiz-fusion. Immediately after, wireless is broken again. So I yum erase kmod-wl-PAE and then yum install kmod-wl-PAE and it works again.
Now, only slightly later that same day, wireless stops working more or less randomly and I cannot get the reinstall of kmod-wl-PAE to fix it. So I uninstall, disable compiz-fusion, shut down, and restart the computer to try again. My thought is that maybe along the way my autostart compiz or something about compiz is causing the wireless not to configure properly. When I restart, wireless is working. Without kmod-wl-PAE installed:
yum info kmod-wl-PaE Loaded plugins: presto, refresh-packagekit Available Packages Name : kmod-wl-PAE Arch : i686
[Code].....
One, how is this even possible, and two, what is going on with the wireless working, not working, working, not working?
I've been running FC10 with all updates and had downloaded the FC11 DVD. Yesterday I upgraded to FC 11 using the DVD and it appeared that everything went fine. However when I tried to do ayum updateI got the following error. There was a problem importing one of the Python modules required to run yum. The error leading to this problem was:
No module named yum
install a package which provides this module, or verify that the module is installed correctly.
It's possible that the above module doesn't match the current version of Python, which is:
2.6 (r26:66714, Mar 17 2009, 11:44:14) [GCC 4.4.0 20090313 (Red Hat 4.4.0-0.26)]
go to the yum faq at: [URL] I'm not sure what to do next. I also noticed that all my previously configured repositories are lost.
Have blacklisted Nouveau in Modpobe... (Haven't done anything to grub.conf)... Have also tried to go the akmod route; but have never been able to make it work..
Have followed the instructions from Post 2 at the beginning of this thread; but I do get a message that says: "No package xorg-x11-drv-nvidia-libs.x86_64 available". I do have both rpmfusion repositories downloaded..
I have used a quite obscure device called Cideko AK0b [URL] .... for quite some time now and it has worked perfectly for almost 2 years now, both in Wheezy and in Jessie. However since I made an dist-upgrade a while back the mouse has totally stopped working. The system works through wifi - strangely enough - but everything else works. Keyboard and gamepad buttons. The manufacture says the things doesn't work on linux and so far I have proved them wrong.
But now the mouse is just out right dead no matter what I do. Have looked into mouse autosuspend but no avail so far. My suspicion is systemd but that is as good as any guess.
Running 3.14-2-amd64.
This is my dmesg.
Code: Select allroot@cryptserv:/home/dencrypt# dmesg | grep Cideko [ 3.158099] usb 6-3: Manufacturer: Cideko Inc. [ 3.469194] input: Cideko Inc. AK08b Device as /devices/pci0000:00/0000:00:12.1/usb6/6-3/6-3:1.0/0003:20E8:5860.0001/input/input2 [ 3.469329] hid-generic 0003:20E8:5860.0001: input,hidraw0: USB HID v1.10 Keyboard [Cideko Inc. AK08b Device] on usb-0000:00:12.1-3/input0
I have updated FC 11 on my hp 6730b laptop as $ su -c 'yum -y update'after updating I logged to kernel '2.6.30.10-105.2.23.fc11.i686.PAE', but my wireless is notworking any idea how to solve it. I have to solve it offline since I have only wireless internet at my work.
When originally installing 11.04 I had problems getting my Ralink 5390 wireless card to work.
Today my computer froze completely and I had to turn it off via the power switch. When I turned it back on, wireless was no longer recognized! My iPod can connect to the network just fine, so it must be an Ubuntu problem. There are no problems with my ethernet connection either.
I researched this and found several threads about blocking and unblocking wireless devices using the rfkill command. Well, unfortunately for me the rfkill command doesn't work. When I type sudo rfkill list or sudo rfkill unblock all, nothing happens; it just returns me to my bash prompt. I even tried uninstalling and reinstalling rfkill...nothing.
I'm currently running Ubuntu 9.10.After I updated to 9.10, my wireless connection stoppped working. I can access the network but I get no response or what so ever in my browser.Downloading language support or any software doesn't work either.Haven't changed anything to my settings and checked the router. Router works just fine.
I know theres a thread for this for fc9 but thats probably kind of outdated now. So I am trying to set up a wireless connection for a pc in my bedroom and just want something that will work out of the box.
i have a dell 1501 that has been upgraded from 10.10 to 11.04. everything was working okay. and then the user ran an upgrade recently. subsequently the wifi has mysteriously stopped working. it connects okay if one plugs it directly into the router but the wifi seems to have just stopped working.my mini 9 connects fine to the netgear wifi router using wireless.when i run the system tests for networking i get the errors..."root could not find def gateway info /proc""root could not find default gateway by running route"here is the output from some diagnostic commands.NOTE:this is similar to a post titled "wi-fi dead?" but the output is not quite the same...
lauren@lauren-Inspiron-1501:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions.
pulled the wireless USB adapter out of the back of my laptop when I was using it. I plugged it back in and it can see my wireless network, but it can't connect. Everytime it tries, it just shows the connecting icon on the top bar for a few minutes and then says that the network has been disconnected.
I've tried uninstalling and reinstalling the USB adaptor, but nothing I've done seems able to fix the issue. Anyone know how to fix this?
I have had ubuntu about a month now and everything has worked great up until now, I was surfing the web and all the sudden I lost connection. I tried to connect to the signal but got nothing so I did a reboot. After the reboot my wireless signal didn't show up. i right clicked the connection icon on the top taskbar and the enable wireless is blacked out to where i cant click it.
Just recently the wireless stopped working on Ubuntu 10.04. The machine is AcerOne AOA-150. I did notice recently the wireless would stop working, and I would need to either 1) reboot 2) switch the wireless off by moving the switch from left to right in front of the laptop.
However, this time nothing is working. I've provided some detail and if more information is needed, let me know.
Well I guess the topic says it all. I've recently upgraded to Maverick from Lucid all went smoothly until i restarted and realized that the remote desktop server included stopped functioning all of a sudden. tried other vnc servers with no luck.
After upgrading to the latest Ubuntu, my wireless card stopped working. I keep on pressing the button but the little orange light wont come on...I have an aspire 5517 with "Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)" I have tried drpjkurian's tutorial for madwifi with no success . (http://ubuntuforums.org/showthread.php?t=1309072
I updated to 10.04 recently and everyhting worked fine. Yesterday my wireless stopped working. Now I just get "Networking disabled" when I mouse over the greyed out wireless icon. Everything still works fine when I boot windows.
Here's the details from the HOWTO log an wireless issue guide http://ubuntuforums.org/showthread.php?p=6183681 . sorry for the length of dmesg and lsmod , I couldn't figure out how to add a spoiler tag on this forum. code...
About a week ago I upgraded to Maverick from Lucid.
All networking worked fine on Lucid.
I am using an Acer Laptop with the Atheros AR928X Wireless Network Adapter.
I can connect to my home network (visible, with WPA2-Personal) fine. However, I cannot connect to my university's wireless network. The only difference I noticed is that its network is using WPA2 Entreprise with Tunneled TLS Authentication and MSCHAPv2.
I have a HP Mini 5105 SSD netbook, runing Ubuntu 10.10 with 2Gb RAM. My wireless card is a Broadcom BCM43224 802.11a/b/g/n. Its driver is enabled and running. The wired network connection runs fine too. The problem: Wireless stopped working. When I right click on the network icon, the enable network option is clicked, but the "enable wireless" option is listed in dark grey and cannot be clicked on. I have recently updated my kernel version to 2.6.35-24-generic. What I have already tried: this one too I got to know there seems to be a problem with the 2.6.35-24-generic kernel. I have gone into the GRUB menu (it took some time to find out that you have to keep the Shift key pressed during startup for the GRUB menu to show), chosen the older kernel version (2.6.35-23-generic) and then removed the faulty one. Nevertheless, nothing has changed. I still cannot enable the wireless. The outcome to lshw -C network is:
I'm running a gateway lapbook w/10.04 LTS and an etheros wirless card. Card has been working fine for almost a year - from cold boot, warm boot, and recovery from standy (shut lid, open, press power button). I was fiddling with setting a static IP for the wirelss card by modifying the interfaces text file. I made some changes, and restored the file to its original contents after some noodling around. Wireless still worked fine after that. Last night I took the laptop out of suspend as usual - lifted lid, pressed power button - but the wireless indicator remained grayed out and I haven't been able to reenable wireless connectivity since. ifconfig shows the wireless card is there, and cabling the e-net port directly to my hub works fine.
I go to the icon and it says "wireless is disabled by hardware switch", well I didn't press any hardware switch. My laptop is a Dell L501X, the "hardware switch" is the Fn button and F2. I've tried pressing this but nothing happens.
Is this a bug with the latest linux version? Cos everything was working fine until my laptop updated.
The version I have now is "Linux 2.6.38-10-generic"
I'm running 11.04 64bit.
Here is some info from console :
Quote:
me@XPS-L501X:~$ sudo ifconfig -a eth0 Link encap:Ethernet HWaddr f0:4d:a2:59:00:34 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::f24d:a2ff:fe59:34/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
