I am trying to install FC14 on a Power 1800. I get hte message that installation stoped due to fatal error whn trying to install module.init.tool package.
This is a repetitive error. I burned a new CD, checked it but get the same error.
The exact message is: A fatal error occurred installing the module-init-tools package. This could indicate errors when reading the installation media. Installation cannot continue.
for some reason my first updating was interrupted and from then i cannot update. i get the following message:
rpmdb: PANIC: fatal region error detected; run recovery
error: db3 error(-30974) from dbenv->open: DB_RUNRECOVERY: Fatal error, run database recovery
error: cannot open Packages index using db3 - (-30974)
error: cannot open Packages database in /var/lib/rpm
CRITICAL:yum.main:
Error: rpmdb open failed
[root@laptop etc]# yum repolist
[Code]....
I must say, the RPMfusion version of the Nvdia driver package work better with FC10 than they did under FC9 for me, which is to say: they work at all. Still get corrupted output after a few hours of work, but I imagine that's just the underlying weakness of the Nvidia driver bubbling up. Either way, now I have other problems:
First off, the Intel driver for my onboard video setup has stopped working entirely. The attempt to bring up X on the Intel setup gets me to the KDE login screen and locks the machine up hard (poweroff required). A look at the xorg.0.log shows that the server seems to be stuck in a loop trying to determine the valid video properties for the session.
Here's my xorg.conf, BTW. I have it setup to perform different configurations depending on which DefaultServerLayout line gets uncommented (lines 4 - 6). If anybody has a better way of doing this, I'm all ears. While we're on my xorg.conf, pleas view lines 64-67 and/or 75-77. This is my quickie way of changing drivers (again, all ears) which brings us to the next problem, neither the nv or nouveau drivers work with my system. Interestingly enough, both drivers tend to fail in the same relative spot in the process, I think. Please refer to line 207 of this xorg.0.log with the nv driver or line 140 of this xorg.0.log from the nouveau setup. Either way, both sessions die with the same message: (EE) Screen(s) found, but none have a usable configuration. Fatal server error: no screens found Gotta go, x session getting corrupt,,,
I have installed fedora, the installation very well took place, only I have a problem to reach the system in graphical mode, and when I tap " startx " in the console it shows the following error:
Fatal IO error 104 (connection reset by peer) on X server ":0.0" after 0 requests (0 known processed) with 0 events remaining.
i have ubuntu karmic 9.10 and when i try to update anything or install anything the a very similar error occurs."(Reading database . . . 55%dpkg: unrecoverable fatal error , aborting: files list file for package `com.palm.net.precoddr.fcoaster' contains empty filenameit repeats this message 3 times then gives up i believe.
View 9 Replies View RelatedQuote:dpkg: unrecoverable fatal error, aborting: failed in buffer_read(fd): files list for package `sysvinit-utils': Input/output errorE: Sub-process /usr/bin/dpkg returned an error code (2)This is the error i get when i try to update my system, fresh install of ubuntu 9.10
View 2 Replies View RelatedI am having trouble installing the 10.04 RC On my desktop the installer just crashes with a fatal error, before you get to the first screen of the installation process, where you choose to run as live cd or install. On my Laptop i am trying to Install alongside my current 9.10 installation and i keep getting the errors illustrated in the screenies. It is all probably down to my stupidity, but if it is not then this is very worrying 1less than a week before release.
View 8 Replies View RelatedThis box is running 10.04 server, it's been running perfectly for almost 6 weeks. It's only function in life is running MailArchiva which is an ediscovery package, runs very well. Anyhow, yesterday the boss tells me he wants to do something else so the last thing I did was an apt-get update and an apt-get upgrade, no errors were observed, I seem to remember like 8 updates were available, this is what I've normally done in the past to keep it current. The last thing I did after that was shutdown -r now.
This morning I can't get into the box, I reconnected a monitor to it and this is the error I'm getting when it stops after about 9 lines into the boot process;
modprobe: FATAL: Error inserting padlock_sha (/lib/modules/2.6.32-24-server/kernel/drivers/crypto/padlock-sha.ko): No such device.
This is a mystery to me, the system is not encrypted. The only stuff that is belongs to MailArchiva. Anyhow someone evidently made off with my install cd so I am downloading another to see if I can repair this but I have no idea what broke.
I have been following this tutorial [URL]. When I get to the end of the installation and try to install GRUB to the /boot partition I have set up it throws a fatal error at me. No explanation other than it can't write to the specified location. I double checked all the partition settings which were the same as the tutorial then skipped the GRUB installation and finished. The only thing I can think of that might be wrong is that the 250MB partition size specified for /boot in the tutorial is too small.
View 2 Replies View RelatedI upgraded postfix to 2.8 today after the security bulletin from the list.
now I get the following error:
'postfix/local[2442]: fatal: unable to determine open file limit'
I can receive/send mail, it just wont let me deliver locally
uname output: 2.6.37-1-686 #1 SMP Tue Feb 15 18:21:50 UTC 2011 i686 GNU/Linux
Last night software updater notification showed 29 updates. I was building a liveCD image so decided create the image first then install the updates. After the updates were finished, I did a reboot because some packages required it, I logged on successfully, then I shutdown for the night. This morning when I executed the same command used to create the liveCD image, I get the following error.
[Code]....
Tonight I installed ubuntu 10.10 (32 bit) on an external usb harddrive with a dvd I burned and I used my older desktop. I disconnected all internal and external drives first so everything had to be put on the usb drive I selected (only option available). I used the option to load extra software, use the entire hard drive, and let the software do it's thing. I basically had no options where to put things and it didn't have much choice.
When I boot the usb drive on my laptop (win 7 64 bit) by telling the bios to boot to it first... I get an error: modprobe: FATAL Could not load /lib/modules 2.6.35-22 generic modules No such file or directory. This message appears twice and then it does boot into ubuntu and seems to work fine. I'm new to this OS so that is an uneducated guess but the things I have done seem to be working. So exactly what is this error referring too? Is there a way to fix the problem or do I just ignore it.
I want to turn an old (2004) compaq computer into a webserver using debian. 2.8ghz celeron, 756mb ram, 80gb IDE HD.I installed debian through the first DVD, without laptop and desktop environments, and did a guided partition.This is the second time this problem has occurred, at first i thought i would try re-installing, but no avail.
As soon as i turn the computer on, i get a grub loader screen with two options, Debian or single user debian. Both choices present same issue. Once i select either one, it seems to load then says "fatal: error inserting fan: no such device." Continues to load, and then "fatal: error inserting thermal, unknown symbol in module"Continues to load then "volume group ***** not found, volume group ***** not found" "enter pass phrase to unlock disk" I enter the pass phrase. "Successful" then a bunch of stuff loads and hangs at "end trace de8............" And it won't let me type anything or do anything except hit the power button.
I updated the latest kernel and other new maintenance tonight and started getting this error at boot...doesn't appear to be hindering anything. My encrypted partitions (luks, ext4) still open and are accessible.
modprobe: FATAL: Error inserting padlock_sha (/lib/modules/2.6.29.5-191.fc11.i586/kernel/drivers/crypto/padlock-sha.ko): No such device
See similar errors reported on ubuntu forums... with various recommended workarounds... update/add an alias, blacklist a module, fresh install
I have been a regular user of Linux and have never faced a problem like this one, after I installed Linux Fedora 14 on my laptop. After installation, almost all the softwares that I was earlier using with the earlier version of Fedora are stopping immediately on starting and exitting with a fatal error. eg. when I try to run paraview, it immediately closes after giving some fatal error. Similar is the case with gambit, tecplot and mayaVi softwares.With my earlier version of Fedora, I was not facing any problem. But since I installed Fedora 14, I am facing this problem. I even tried by downloading and installing latest version of paraview and mayaVi from the net, but the latest versions also on starting give the same error : fatal error, and exit the program.
The softwares I mentioned immediately close indicationg a fatal error. The following error messages appear in the console after abrupt shut down of softwares with fatal error :
Output of /var/log/message file:
I installed fedora 10 on my laptop. But I am getting this error when it is booting up:
Code:
Release Date : 5 November 2008
X Protocol Version 11 , Revision 0
[code]....
Trying to Interface USB Wifi Dongle with Linux (Fedoracore 8 While giving modprobe zd1211rw following FATAL Error throws;
[root@localhost linux-2.6.22.18]# /sbin/modprobe zd1211rw //////////////modprobe command
WARNING: Error inserting ieee80211_crypt (/lib/modules/2.6.23.1-42.fc8/
kernel/net/ieee80211/ieee80211_crypt.ko): Invalid module format
WARNING: Error inserting ieee80211 (/lib/modules/2.6.23.1-42.fc8/
kernel/net/ieee80211/ieee80211.ko): Invalid module format
[Code]...
Trying to Interface USB Wifi Dongle with Linux (Fedoracore 8)
While giving modprobe zd1211rw following FATAL Error throws;
How to overcome this FATAL Error? What prerequisites need to check?
I am getting an error from yum update and Kpackagekit:
[root@asus-m4n82 tylerm]# yum update
Loaded plugins: refresh-packagekit
Setting up Update Process
rpmdb: page 18816: illegal page type or format
[code]....
How do I "run recovery"? Edit: Ok so it looks like I had som bad ram in my system that caused this - I found a site that told me to do this:
rm -f /var/lib/rpm/__db*
rpm rebuilddb
yum clean all
I did this but now when I try something like yum install firefox it pulls in a ton of already installed packages.
I'm tring to run AMDOverdriveCtrl, since they don't have an RPM file for Fedora i tried to compile from source i followed the instruction in the readme files run the make command
Code:
% make
g++ -mwindows -s -pthread -lwx_gtk2u_richtext-2.8 -lwx_gtk2u_aui-2.8 -lwx_gtk2u_xrc-2.8 -lwx_gtk2u_qa-2.8 -lwx_gtk2u_html-2.8 -lwx_gtk2u_adv-2.8 -lwx_gtk2u_core-2.8 -lwx_baseu_xml-2.8 -lwx_baseu_net-2.8 -lwx_baseu-2.8 -ldl -o./Release/AMDOverdriveCtrl ./src/CFanSpeedPanel.o ./src/COvdrSettingsPanel.o ./src/CFanControlPanel.o ./src/CColorTempPanel.o ./src/BezierMath.o ./src/Color.o
[code]....
and tried to run the application, and i get this error message
Code:
$ AMDOverdriveCtrl
Fatal Error: Mismatch between the program and library build versions detected.
The library used 2.8 (no debug,Unicode,compiler with C++ ABI 1002,wx containers,compatible with 2.4,compatible with 2.6), and your program used 2.8 (no debug,Unicode,compiler with C++ ABI 1002,wx containers,compatible with 2.6).
I am trying to install fedora 10 kickstart on my server.But I can't, because my kickstart installation hangs at post install scripts.It is not showing any message & stopped.
View 1 Replies View Relatedi tries to upgrade my fc14 to fc15 using preupgrade. during installation packages process i get an error "fatal error bla-bla-bla installing netsniff-ng-...". i've booted in fc14 (in emergency mode) and manually removed old netsniff-ng package and installed new package. after that i've booted in preupgrade process. it finishes successfull. but now i can't boot in fc15 - i get "kernel panic" error. i've opened grub.conf and there is no 'initrd' section and there is no initramfs for fc15 in /boot folder. i've tried to boot fc15 with initrd /initramfs-bla-bla-fc14.i686.PAE.img. fc15 booted, but i think something wrong, because network not working, and there is only "lo" in ifconfig. what can i do?
View 14 Replies View RelatedI had an earlier thread with wrong title and wasn't sure of the problem at the time. Now I have some details after checking all the threads about catalyst so posting a new thread. The problem: In korganizer (or To-Do list in kontact), whenever double-clicking or right-click->Edit.. a To-Do item in the summary list window, it crashes Xorg.
[Code]...
Fatal server error: Caught signal 11 (Segmentation fault). Server aborting I think it has something to do with the amd/ati catalyst driver and korganizer. My video card is XFX Radeon HD5670. I have Fedora 14 x86_64 latest update with xorg 1.9.1-3. I tried catalyst 10.9, 10.10, 10.11, and kernel 2.6.35.6-45.fc14.x86_64, 2.6.35.6-48.fc14.x86_64, 2.6.35.9-64.fc14.x86_64. Same problem.
If I use vesa driver, or from another PC with proprietary nvidia driver, no problem. Open source radeon driver works ok but sometimes the display turns off and I can't get back the display. And I need 3D. I scoured through the forum and followed the instructions exactly:
[code]...
Ive installed about 50+ boxes with ubuntu/mint/fedora/etc but f15 is giving me a real headache...
I tried a fresh install over f14 with this drive (sdb, sda is my backup disk)
Installed obviously in part7
After rebooting (successful copied live image on hdd)
Code:
After another couple of installs (with lvm & w/o lvm) & even disconnecting the second harddrive -> same issue
Typing 'ls' in the rescue grub prompt returns
Code:
Cant 'ls /' into a single them - unknown filesystem (grub is installed in mbr of sdb) 'linux rescue' (wanted to try manual grub installation) command didnt work either.
Now again on fedora 14, same installation procedure, works fine. (and i wont bother doing a full distro upgrade from f14)
I am trying to install Fedora 11 from the full DVD iso on a system using an Intel D945GNT motherboard with a dual-core 3.2GHz Pentium D installed. The installation hangs quite quickly and produces the error "Kernel panic - not syncing"... The previous line is something along the lines of "EIP: [something] intel_i915_configure() [something else]". I have tried many different kernel boot options, such as acpi=off, nolapic, nommconf, and the like, but to no avail. It seems as though this has something to do with a memory mapping conflict due to the allocation of video memory for the on-board graphics chip, but I'm not at all certain about that.
View 3 Replies View RelatedI'm trying to do a fresh install of fedora 12 on a Dell optiplex 380, using the fedora 12 i686 DVD. During the installation process I get a network driver installation error shown below. Anyone know how to resolve this?
View 6 Replies View RelatedTrying to give Fedora a proper trial by installing it on my main machine's hard drive. I tested the Live CD from a USB drive for a while and really liked it. Fedora is the first distro that I've tried that does Gnome Shell justice.
I haven't been able to get it to work on my system so far, however.
Some context: I have a triple-boot laptop (Windows 7, Debian, and now Fedora 15) with 4 physical partitions (True Crypt-encrypted W7, LUKS-encrypted Debian, LUKS-encrypted F15, and a boot partition). The True Crypt boot loader is on the MBR, and when I press Esc I get the Grub boot loader from the boot partition. This has worked well for me in the past, but something is awry now.
When I installed F15, I did not opt to install a boot loader (because I didn't want to have trouble getting into my other systems, which has happened to me before). Instead I booted up into Debian and ran update-grub, which found the Fedora partition and added an entry to Grub. I'm not sure whether that entry is correct, however, but editing it has not solved my problem.
When I choose the Fedora entry from Grub, it starts to boot and asks for the password to mount the partition. Shortly afterwards, however, it throws the following error: modprobe: FATAL: Error inserting padlock_sha (/lib/modules/kernel-name-here/kernel/drivers/crypto/padlock-sha.ko): No such device
Then it drops down to a shell and I can't do much from there.
I've tried blacklisting padlock-sha, but that doesn't make the error go away or get it to boot up.
Ive tried to install Fedora 14 in a VMware Workstation 7.1.3 and theres the following error: "Running anaconda 14.22, the Fedora system installer, please wait. 23:19:38
The following error was found while parsing the kickstart configuration file:
The following ocurred on line 65 of the kickstart file:
I've just install qemu-kvm from [URL]
I run modprobe kvm and modprobe kvm-intel to load the modules, but the second command won't work.
It gives the following error -
Code:
root@mika:/home/mika# modprobe kvm-intel
FATAL: Error inserting kvm_intel (/lib/modules/2.6.33.4/kernel/arch/x86/kvm/kvm-intel.ko): Operation not supported
I'm runing FC11 and have compiled the vanilla kernel 2.6.33.4 to support Dazuko. It has broken my NFSD server in the process, and I can't figure out why. I get these errors on boot. FATAL: Module nfsd not found. FATAL: Error running install command for nfsd
[code]....