Fedora :: FATAL - Error Inserting Padlock_sha With 2.6.29.5-191 Kernel
Jun 25, 2009
I updated the latest kernel and other new maintenance tonight and started getting this error at boot...doesn't appear to be hindering anything. My encrypted partitions (luks, ext4) still open and are accessible.
modprobe: FATAL: Error inserting padlock_sha (/lib/modules/2.6.29.5-191.fc11.i586/kernel/drivers/crypto/padlock-sha.ko): No such device
See similar errors reported on ubuntu forums... with various recommended workarounds... update/add an alias, blacklist a module, fresh install
I recently started having this odd behaviour while using and loading cpufrequtils on boot, I don't know if it is happening to someone else.During boot I'm getting( when /etc/init.d/cpufrequtils invokes /etc/init.d/loadcpufreq to load the proper module):
Loading cpufreq kernel modules...FATAL: Error inserting speedstep_centrino (/lib/modules/3.0.0-1-amd64/kernel/drivers/cpufreq/speedstep-centrino.ko): No such device FATAL: Error inserting pcc_cpufreq (/lib/modules/3.0.0-1-amd64/kernel/drivers/cpufreq/pcc-cpufreq.ko): No such device
I took some pictures tonight and plugged in my flash card reader (via usb) as always. Only this time, the device isn't assigned a proper location (like "sdc3").
A little research later and I *think* I need the module "usb-storage", which I can't get to load. It's been a *long* time since I had to mess with modules and I'd like some fresh eyes on what the problem might be.
This is my lsmod output:
Code:
I also ran modprobe with -n -v:
Code:
I have run depmod -a and tried the modprobe again...
Code:
If I drill down to the /lib/modules/<kernel -r>/drivers/usb/storage/ where the .ko file is and say:
Code:
So.... since I haven't changed anything that I can think of since the last time I took pictures...what happened? How do I fix this?
So I am new to ubuntu and am trying to work with "iptables". I have ubuntu version 10.04, in the terminal I try to create a new iptable by writing: iptables -N chain but the response is: FATAL: Error inserting ip_tables......... also it says "you must be root", what does root mean?
I am running ubuntu 10.04 I am trying to access the tty's
When I hit Ctrl + Alt + F1 I get a screen that says: FATAL: Error inserting uvesafb (/lib/modules/2.6.32-23-generic/kernel/drivers/video/uvesafb.ko): unknown symbol in module, or unknown parameter (see dmesg)
Ctrl + Alt + F2-F6 all I get is a flashing cursor that won't do anything
(Opensuse 11.4, nvidia, core2) PROBLEM: cpu goes into C3 powersaving state even on full load (even when disabled from bios) (acpi=off prevents this). opensuse 11.4 kernel ignores boot option processor.max_cstate=2 (option has no effect). cpufreq util should be able to change governor policy to performance, however acpi-cpufreq driver doesn't load: modprobe acpi-cpufreq -> FATAL: error inserting acpi_cpufreq (/lib.../acpi-cpufreq.ko): No such device
I have a problem with loading the powersaving kernel module p4-clockmod.ko. When I try inserting the module (via modprobe or insmod) I get FATAL: Error inserting p4_clockmod (/lib/modules/2.6.31.8-mediaserver/extra/p4-clockmod.ko): Invalid module format The module has been compiled together with the kernel. Other modules load with no problem at all. I've tried recompiling the kernel (after re-installing the sources, make xconfig from scratch) - no avail. There's only one kernel source package installed. Searching the forum and google didn't yield a helping answer.
# xorg.conf (X.Org X Window System server configuration file) # # This file was generated by dexconf, the Debian X Configuration tool, using # values from the debconf database.
[code]...
And after that my X is not working. And when i try sudo modprobe nvidia I get this:
FATAL: Error inserting nvidia (/lib/modules/2.6.26-2-686/nvidia/nvidia.ko): No such device
I want to turn an old (2004) compaq computer into a webserver using debian. 2.8ghz celeron, 756mb ram, 80gb IDE HD.I installed debian through the first DVD, without laptop and desktop environments, and did a guided partition.This is the second time this problem has occurred, at first i thought i would try re-installing, but no avail.
As soon as i turn the computer on, i get a grub loader screen with two options, Debian or single user debian. Both choices present same issue. Once i select either one, it seems to load then says "fatal: error inserting fan: no such device." Continues to load, and then "fatal: error inserting thermal, unknown symbol in module"Continues to load then "volume group ***** not found, volume group ***** not found" "enter pass phrase to unlock disk" I enter the pass phrase. "Successful" then a bunch of stuff loads and hangs at "end trace de8............" And it won't let me type anything or do anything except hit the power button.
insmod: error inserting 'kernel.ko': -1 Invalid parametersI am getting this error when i am try to insert kernel.ko into kernelMy systemfedora 12 with gcc 4.4.2insmod kernel.koinsmod: error inserting 'kernel.ko': -1 Invalid parametersmy program
Trying to give Fedora a proper trial by installing it on my main machine's hard drive. I tested the Live CD from a USB drive for a while and really liked it. Fedora is the first distro that I've tried that does Gnome Shell justice.
I haven't been able to get it to work on my system so far, however.
Some context: I have a triple-boot laptop (Windows 7, Debian, and now Fedora 15) with 4 physical partitions (True Crypt-encrypted W7, LUKS-encrypted Debian, LUKS-encrypted F15, and a boot partition). The True Crypt boot loader is on the MBR, and when I press Esc I get the Grub boot loader from the boot partition. This has worked well for me in the past, but something is awry now.
When I installed F15, I did not opt to install a boot loader (because I didn't want to have trouble getting into my other systems, which has happened to me before). Instead I booted up into Debian and ran update-grub, which found the Fedora partition and added an entry to Grub. I'm not sure whether that entry is correct, however, but editing it has not solved my problem.
When I choose the Fedora entry from Grub, it starts to boot and asks for the password to mount the partition. Shortly afterwards, however, it throws the following error: modprobe: FATAL: Error inserting padlock_sha (/lib/modules/kernel-name-here/kernel/drivers/crypto/padlock-sha.ko): No such device
Then it drops down to a shell and I can't do much from there.
I've tried blacklisting padlock-sha, but that doesn't make the error go away or get it to boot up.
I'm runing FC11 and have compiled the vanilla kernel 2.6.33.4 to support Dazuko. It has broken my NFSD server in the process, and I can't figure out why. I get these errors on boot. FATAL: Module nfsd not found. FATAL: Error running install command for nfsd
Last night software updater notification showed 29 updates. I was building a liveCD image so decided create the image first then install the updates. After the updates were finished, I did a reboot because some packages required it, I logged on successfully, then I shutdown for the night. This morning when I executed the same command used to create the liveCD image, I get the following error.
I have been a regular user of Linux and have never faced a problem like this one, after I installed Linux Fedora 14 on my laptop. After installation, almost all the softwares that I was earlier using with the earlier version of Fedora are stopping immediately on starting and exitting with a fatal error. eg. when I try to run paraview, it immediately closes after giving some fatal error. Similar is the case with gambit, tecplot and mayaVi softwares.With my earlier version of Fedora, I was not facing any problem. But since I installed Fedora 14, I am facing this problem. I even tried by downloading and installing latest version of paraview and mayaVi from the net, but the latest versions also on starting give the same error : fatal error, and exit the program.
The softwares I mentioned immediately close indicationg a fatal error. The following error messages appear in the console after abrupt shut down of softwares with fatal error :
for some reason my first updating was interrupted and from then i cannot update. i get the following message:
rpmdb: PANIC: fatal region error detected; run recovery error: db3 error(-30974) from dbenv->open: DB_RUNRECOVERY: Fatal error, run database recovery error: cannot open Packages index using db3 - (-30974) error: cannot open Packages database in /var/lib/rpm CRITICAL:yum.main: Error: rpmdb open failed [root@laptop etc]# yum repolist [Code]....
I'm tring to run AMDOverdriveCtrl, since they don't have an RPM file for Fedora i tried to compile from source i followed the instruction in the readme files run the make command
and tried to run the application, and i get this error message
Code:
$ AMDOverdriveCtrl Fatal Error: Mismatch between the program and library build versions detected.
The library used 2.8 (no debug,Unicode,compiler with C++ ABI 1002,wx containers,compatible with 2.4,compatible with 2.6), and your program used 2.8 (no debug,Unicode,compiler with C++ ABI 1002,wx containers,compatible with 2.6).
i tries to upgrade my fc14 to fc15 using preupgrade. during installation packages process i get an error "fatal error bla-bla-bla installing netsniff-ng-...". i've booted in fc14 (in emergency mode) and manually removed old netsniff-ng package and installed new package. after that i've booted in preupgrade process. it finishes successfull. but now i can't boot in fc15 - i get "kernel panic" error. i've opened grub.conf and there is no 'initrd' section and there is no initramfs for fc15 in /boot folder. i've tried to boot fc15 with initrd /initramfs-bla-bla-fc14.i686.PAE.img. fc15 booted, but i think something wrong, because network not working, and there is only "lo" in ifconfig. what can i do?
I had an earlier thread with wrong title and wasn't sure of the problem at the time. Now I have some details after checking all the threads about catalyst so posting a new thread. The problem: In korganizer (or To-Do list in kontact), whenever double-clicking or right-click->Edit.. a To-Do item in the summary list window, it crashes Xorg.
[Code]...
Fatal server error: Caught signal 11 (Segmentation fault). Server aborting I think it has something to do with the amd/ati catalyst driver and korganizer. My video card is XFX Radeon HD5670. I have Fedora 14 x86_64 latest update with xorg 1.9.1-3. I tried catalyst 10.9, 10.10, 10.11, and kernel 2.6.35.6-45.fc14.x86_64, 2.6.35.6-48.fc14.x86_64, 2.6.35.9-64.fc14.x86_64. Same problem.
If I use vesa driver, or from another PC with proprietary nvidia driver, no problem. Open source radeon driver works ok but sometimes the display turns off and I can't get back the display. And I need 3D. I scoured through the forum and followed the instructions exactly:
I must say, the RPMfusion version of the Nvdia driver package work better with FC10 than they did under FC9 for me, which is to say: they work at all. Still get corrupted output after a few hours of work, but I imagine that's just the underlying weakness of the Nvidia driver bubbling up. Either way, now I have other problems:
First off, the Intel driver for my onboard video setup has stopped working entirely. The attempt to bring up X on the Intel setup gets me to the KDE login screen and locks the machine up hard (poweroff required). A look at the xorg.0.log shows that the server seems to be stuck in a loop trying to determine the valid video properties for the session.
Here's my xorg.conf, BTW. I have it setup to perform different configurations depending on which DefaultServerLayout line gets uncommented (lines 4 - 6). If anybody has a better way of doing this, I'm all ears. While we're on my xorg.conf, pleas view lines 64-67 and/or 75-77. This is my quickie way of changing drivers (again, all ears) which brings us to the next problem, neither the nv or nouveau drivers work with my system. Interestingly enough, both drivers tend to fail in the same relative spot in the process, I think. Please refer to line 207 of this xorg.0.log with the nv driver or line 140 of this xorg.0.log from the nouveau setup. Either way, both sessions die with the same message: (EE) Screen(s) found, but none have a usable configuration. Fatal server error: no screens found Gotta go, x session getting corrupt,,,
I am running Red Hat with 2.6.18-194.8.1.el5PAE kernel version. I am trying to run encryptfs to encrypt a partition on my hard drive. One of the kernel modules necessary is the md5.ko. I noticed it wasn't loaded in when doing an lsmod. I tried running modprobe md5 and it fails to load:
I have installed fedora, the installation very well took place, only I have a problem to reach the system in graphical mode, and when I tap " startx " in the console it shows the following error:
Fatal IO error 104 (connection reset by peer) on X server ":0.0" after 0 requests (0 known processed) with 0 events remaining.
