Ubuntu Networking :: Setup Network For Both The Internet And WUG At The Same Time?

Aug 27, 2010

There is 2 networks that I would like to be part of

a) Through my wlan0 --> Internet DSL

and

b) Through my eth0 --> WUG - PTAWUG

I can only get one of the networks to work at 'n time. The wlan0 works fine when I start my PC, but when I want to access the WUG I need to do the following command:

Code:

sudo route add -net 172.16.0.0 netmask 255.240.0.0 gw 172.24.6.177 dev eth0

with the above command, I can then access the WUG but not the internet through my wlan anymore.all data goes to my wlan as standard unless its on the 172.16.0.0 network

View 5 Replies


ADVERTISEMENT

Networking :: Setup VMware's Network Configuration For Red Hat Can Access Internet?

Apr 7, 2010

I installed and tested both Windows server 2003 and Red Hat 9.0 with vmware workstation7. After installing 2003 can access internet but Red Hat can't. I want to test squid proxy server, send mail server, webserver etc. So, I would like to know how to setup WMware's network configuration for Red hat can access internet.

Below link is the configuration of VMware network setup both Server 2003 and Red Hat.

Here is Red Hat Configuration:
http://i64.servimg.com/u/f64/11/74/16/17/linux10.jpg

Here is Windows Server 2003 configuration:
[url]

I am using wireless connection to access internet.

View 1 Replies View Related

CentOS 5 Networking :: No Wired Network Connection From Time To Time At Logon?

Oct 20, 2010

In the right upper corner of your screen,you can see if you have a network connection or not.Most of the time I do not have one according to Networkmanager (?).So I have to enable my wired connection manually.I already tried a lot to change my settings so I would have a network connection at boot,but it doesn't seem to work....Firefox is in Offline modus when I logon..

View 2 Replies View Related

Ubuntu :: Cannot Connect To Internet - Setup Network Package?

Nov 21, 2008

I have a fresh install of ubuntu. I am trying to load some new packages but I think I need internet connection. The issue is I cannot connect to the internet I think I need to setup a network package so I can connect to the internet? This is the first time I have used linux.

View 3 Replies View Related

OpenSUSE Network :: 11.2 Xen Bridged Networking - Setup Multiple DomU Through The Default Bridge Setup

Feb 4, 2010

Im trying to setup multiple domU through the default bridge setup. I am able to access only one of them through the network at a time. If you ping one of the domU it works perfectly but you cannot ping any of the others until you stop pinging the one and even then it takes a bit before you can. Ive looked around for a while and seen similar problems but nothing ever seems quite the same. Im probably missing something really stupid. Or is this the way the bridge is supposed to behave? Do i need to use a routed virtual network?

[Code]....

View 1 Replies View Related

OpenSUSE Network :: Setup An Internet Connection With 11.2?

Jun 23, 2010

I recently took a WIRED internet connection (from the people who provide cable TV) and switched from ubuntu to openSUSE11.2. . I am not able to set up an internet connection in openSUSE 11.2. I have been given a static IP, and the following info

subnet mask
gateway
dns server
alternate dns server

how do i setup an internet connection with these in openSUSE 11.2.

View 6 Replies View Related

Ubuntu :: Setup Home Network With A File/internet Server

Aug 23, 2010

I'd like to set up my home network with an Ubuntu file/internet server. In addition, I would use this server to monitor internet traffic. What hardware/software would be required?

My current network is as follows:

Laptop 1 Ubuntu 9.1
Laptop 2 Vista
Laptop 3 XP
Desktop Ubuntu 9.04 (would be used as server)

All connected thru linksys wireless router to cable modem.

View 2 Replies View Related

OpenSUSE Network :: Setup Internet Tracking On An 11.3 Computer?

Jul 15, 2010

Is there a good way to set up internet tracking on an openSUSE 11.3 computer? I don't want users visiting porn sites or any other nonsense, and if they do, I want to know about it. Is there a good program that the administrator can set up to report this kind of thing or at least track it? Obviously, this would need to track all websites visited regardless of the application/browser used, and would need to be completely inaccessible to users. I don't want them having the ability to turn it off or circumvent it somehow.

View 8 Replies View Related

Red Hat / Fedora :: Setup Wireless Network To Surf Internet?

Mar 6, 2010

I use Fedora 12 and I use Mobile Boradband to connect to the Internet on my laptop. I want to setup a wireless network using my laptop so that my roommate who uses Vista, can surf internet on his laptop. How can I do it?

View 1 Replies View Related

OpenSUSE Network :: Internet Connection Dies After A Period Of Time

Feb 22, 2011

I am having some trouble with my opensuse 11.3 internet connection for two weeks. After a certain period connection drops while using both NetworkManager and ifup. For info, I write the outputs of some codes.

[Code]...

View 2 Replies View Related

Red Hat / Fedora :: Internet Every Time When System Is Boot Or Network Is Disconnected?

Sep 29, 2010

I got problem in my internet every time when system is boot or network is disconnected i have to enter the DNS address(number) primary and secondary

View 7 Replies View Related

OpenSUSE Network :: Can't Setup Internet Connection Wired Or Wireless

Mar 11, 2011

I have just done a new install of the latest opensuse 32bit and for some reason I cannot connect to the internet, when I click on mange connections the vpn tag is highlighted and all the other tabs are grayed out and I cannot select them. So I can't setup a internet connection wired or wireless. I was just using Kubuntu and did not have this problem. My card is broadcom.

View 9 Replies View Related

Debian Configuration :: Complex Network Setup - RPI To Automatically Route Internet

Jan 26, 2016

I would like to update my network setup.

Today, I have an ADSL box which is my gateway to internet (192.168.0.1).

I have a Raspberry pi (RPI) which I use as a dhcp & dns server (192.168.0.2).

Recently my mobile phone operator installed a 4G antenna beside my home, and the bandwidth and latency are much better with my mobile phone than with my internet provider (ADSL).

I would like to install a wifi dongle on my RPI (I would get wlan0 & eth0 interfaces)

When RPI detect my shared phone connection (tethering) I would like RPI to automatically route internet:

- from authorized devices on my network to my mobile connexion (wlan0 -> mobile phone).
- from other devices to the standard ADSL internet (eth0 -> ADSL box).

I don't want any device to use the shared 4G connexion, best would be authorized devices to be selected by MAC address. How I should properly setup such a network ?

View 2 Replies View Related

Fedora Networking :: Setup The Network Scripts To Create Two Network Interfaces For Vlan X And Y?

Apr 7, 2009

Using Fedora 10, can anyone tell me how to setup the network scripts to create two network interfaces for vlan x and y. Both interfaces should obtain an ip from dhcp and both interfaces should run over eth0.

View 2 Replies View Related

Ubuntu Networking :: Internet Dies After Some Time

Sep 24, 2010

I don't want to 'spam', (I had started a first thread about this some time ago), but I'm (still) experiencing problems with my internet: I can use the internet (I am connected through a simple switch) for some time, that is: surf the internet (in firefox) and download using vuze (azureus) but after some time, the internet connection 'dies' (downloadspeeds jump to 0b/s and I am not able to surf to any site in firefox). When that happens, the only 'solution' to this is restarting my pc.

I first experienced this when using ubuntu 10.04, so I thought that it was a 10.04 issue. I knew that when I had ubuntu 9.10 (karmic koala) installed, this didn't happen. So today, I installed karmic koala, but much to my surprise I am experiencing the same problem. I used 'lspci' to find out what NIC is in my pc and I found out I have the following NIC: 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78 ) I'm suspecting the NIC to be the problem. Is this probable? If so, I want to buy a add-in network card (simple one, not a gigabit card)

View 6 Replies View Related

Fedora Networking :: Cannot Find Network Card While Setup Network Configuration?

May 25, 2010

Cannot activate network device eth0!"device eth0 does not seem to be present, delaying initialization".i cannot find my network card while i set up network configuration Now I use dual boot window 7 and fedora 9,I cannot find my network card in select network adapter while network configuration ,i have a network card Atheros AR8132 PCI-E fast Ethernet controller NDIS(620)and for wired in Accer laptop .

View 1 Replies View Related

Red Hat :: Networking - Setup Network Scripts To Create Two Network Interfaces For Vlan X And Y

Apr 7, 2009

Can anyone tell me how to setup the network scripts to create two network interfaces for vlan x and y. Both interfaces should obtain an ip from dhcp and both interfaces should run over eth0.

View 4 Replies View Related

CentOS 5 Networking :: Setup A Network To Network VPN Tunnel Between Our Main Office And A Temporary Location?

Aug 12, 2009

I am attempting to setup a network to network VPN tunnel between our main office and a temporary location. This location need full VPN access back to the main office's network.Anyhow we have spent about 3 solid days attempting to make this work without any great success. Here is our network scheme for these two devices.

Network A (Main Office) (OpenBSD using isakmpd)
Network: 172.16.8.0/24
External IP: 1.1.1.1 (obviously not the real IP)[code].....

View 2 Replies View Related

OpenSUSE Network :: Adsl Modem Acting As A Bridge To My Router Setup - Connection - Internet Went Slow ?

Jun 19, 2011

I have an adsl modem acting as a bridge to my router my setup was working well for more than year now , but then the internet went slow . I set the modem back to PPPoE the problem was with the DNS server of the ISP so using ifup i set the dns t 8.8.8.8 (google) the connection is back , but when i set the modem back as a bridge slow internet does the router know that my dns is 8.8.8.8 or i should set the dns on the router ? I can't see an option to set the dns on the router ( i just enter my username and password from the isp to use PPPoE mode ) by the way i called the isp support they kept telling me to restart , i told them i did but i never restarted my pc . I'm sure if i tell them i'm running linux they will blame the os !

View 2 Replies View Related

Ubuntu Networking :: How To Setup Wireless Internet

Feb 1, 2010

I just finished downloading the latest version of xubuntu on my dell insperon 1545. I went to set up the internet and i cannot figure out how. In the top right corner the connection icon has only one option that i can select, and thats configure the vpn settings i think. I installed it using dual booting next to windows 7, so i keep switching back and forth trying to look something up and go back to see if it will work. However, i think i should make the point that i've never worked with any linux type o.s. before.

View 7 Replies View Related

Ubuntu Networking :: Not Able To Setup Internet Dialer

Dec 22, 2010

I newly installed ubuntu 9, but I am not able to setup the internet dialer. I am not using cable modem. Lan cable from my isp's switch is directly connected to my Pc's ethernet card. In windows XP one dialer is created using Rasppoe. In ubuntu I tried it using pppoeconf command but itis notable to setup the connection.

View 3 Replies View Related

Networking :: Xen Network-route And Network-bridge Setup?

Aug 22, 2010

I've currently got a Xen box with 3 Virtual machines on it, in a routed setup. I'd like to put them all on a private internal network as well, which I'm assuming I'd do with a dummy network card and a xen bridge, but I can't find any information about setting up the xen Bridging setup on top of the existing network-route instlal.

View 1 Replies View Related

Ubuntu Networking :: No Internet Access Via New Wireless Setup?

Feb 10, 2010

Running Ubuntu 9.10 Ive just got my wireless connection working after first having got the wired eth0 connection working.

With the wired connection I could SSH into my server through my firewall/router (via a forward). I can run up VNC, from there firefox, browse the web - all is well.

I have now setup the wireless connection, using a static IP, and I can likewise SSH into my server. I can run up VNC. I can ping my router. I can log onto it via VNC. I can browse to my router. But I cant browse the internet.

But I cant ping google.com. The reason is there is no host lookup service. Nslookup eventually says no servers could be reached.

So specifically, if I ping www.google.com Im told "unknown host". If I do an NSlookup on it I get timeout, no servers could be reached. However if I ping 66.102.11.104 I get responses.

I see no relevant entries in my firewall log.

Unfortunately I cant traceroute because the package isnt found - and of course I cant install it because I have no internet !

Strangely (to me at least !) if I then tunnel through SSH and browse the web, I have no problems. It works ? I know I am browsing through my SSH tunnel because whatsmyip gives the IP of my router at home, not where Ive SSHd in from. I can surf just fine.

why I cant do host lookups any more (and this did work with my wired connection, but whether its related to my change to wireless, or static IPs or both I cant be sure - it certainly appeared to happen at the same time). And, more to the point, what I need to look for/do to rectify it ?

As a bonus Id be interested in why I can SSH and browse via tunnelling but not direct from my server (via VNC). Just for interests sake !

if config reports :

wlan0 Link encap:Ethernet HWaddr 00:90:4b:27:ae:17
inet addr:192.168.1.69 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::290:4bff:fe27:ae17/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

[Code]....

View 1 Replies View Related

Ubuntu Networking :: How To Setup Wired Internet Connection

Jun 2, 2010

I have BIG troubles trying to set up wired internet connection in Ubuntu! To be able to connect to the internet I have to enter my MAC address, 2 IPs, netmask and 2 DNS address. When I try to edit the default internet connection eth0 with my correct information, the minute I enter my MAC address and save the changes the network manager creates new internet connection with wrong data and use it instead! I can't select the correct internet connection from the top bar where the internet icon is, because it is just not there. The only connection that I can choice is the new default one with the wrong data! If I try to create new separate internet connection with my correct data the same thing happens! The moment I enter my MAC address and save it, the internet connection disapears from the list of internet connections in the internet area in the top bar and I can't select it. I tried googling it, but with no luck I think that if I set up my connection trough the terminal everything will be ok

View 2 Replies View Related

Ubuntu Networking :: Setup User With No Internet Access?

Nov 17, 2010

I would like to set up a user account with no network access. Reason is that sometimes my little daughter plays with the computer (for example watching movies on dvd's) and I want to prevent internet access in case she plays unattended. Is there a simple way to do that? I am using ubuntu 10.04.

View 4 Replies View Related

Ubuntu Networking :: Wired / Wireless Internet Setup

Jan 26, 2011

Just installed ubuntu 10.10 on a Compaq Presario X6000 laptop... installed it inside Windows 7 and now I'm having problems going to the internet (wired.. or wireless).

View 3 Replies View Related

Fedora Networking :: Use Two Internet Connections At The Same Time?

Jun 22, 2009

I have two internet connections. One is wired ADSL Broadband & another is USB EVDO modem. I can use only one source at a time. That means the traffic will pass through either ADSL or EVDO. Other connection just sits idle. I want to use both the connections together so that I will have increased bandwidth. Is there a way to do that?

My computer has one NIC card. Both ADSL & EVDO use dynamic IPs.

View 1 Replies View Related

Ubuntu Networking :: Wireless Internet Modem (USB) And A LAN Ethernet - Connect To Both At The Same Time?

Jul 22, 2010

I have a wireless Internet modem (USB) and a LAN Ethernet connection. I can only pick 1 of them to connect to (by disconnecting the other). How can I connect to both at the same time?

View 6 Replies View Related

Ubuntu Networking :: Every Time Restart Have To Configure Internet Using PPPOE CONF

Jul 25, 2010

i configured my laptop (running UBUNTU 10.04 LTS) for my broadband (bridge mode). I did that using PPPOE CONF command. Everything goes ok but only prob is i have to run this command and configure my net every time i restart my system. What i need is it should connect to the net whenever i use the PON DSL-PROVIDER and must turn off by using POFF..

View 1 Replies View Related

Ubuntu Networking :: Kubunutu 8.10 Setup - Unable To Get Internet Configured?

Feb 10, 2010

I have kubuntu 8.10 up and running however I am not able to get internet configured. this is on a laptop i re-purposed. I have ubuntu on a desktop that works just fine. however w/ kubuntu no such luck. i realize its just kde vs gnome and am connected to the same router and such so all should work just fine, but alas it doesn't.the desktop is configured using dhcp, not static IPs.

the laptop w/ kubuntu isn't recognizing eth0

>cat /etc/network/interfaces displays:

auto eth0
iface eth0 inet dhcp

after restarting and running /etc/init.d/network restart.there is no resolv.conf... i understand dhcp should auto-create this? furthermore running ifconfig desplays no results ?

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved