I have a wireless Internet modem (USB) and a LAN Ethernet connection. I can only pick 1 of them to connect to (by disconnecting the other). How can I connect to both at the same time?
View 6 RepliesI am using a cable modem wired to my PC via ethernet. My ISP is Road Runner, through Time Warner Cable.
I entered my IP address, Netmask, and DNS Servers into the network, not using DHCP. This was how I was able to achieve a network connection.
I am connected to the modem, but I cannot get internet.
Here are my stats:
I have 2 pcs at home. I dont have a switch so I can connect only one PC at a time to my adsl router/modem for internet access. In the past I had successfully connected the two PCs (NIC to NIC) to each other using the same ethernet cable which was supplied with my dlink adsl modem.
Recently the motherboard of on of my PC went bad so I replaced it with a new one. The problem is when I connect the two using the same Ethernet cable they won't connect. The lights on the Ethernet port won't light up. I can still connect both of them to the adsl router (NIC to Router) (one at a time).
Earlier today I decided I wanted to switch back over to ubuntu, my internet was working fine, but as soon as i reformatted to Linux my modem stopped showing any lights under ADSL - TX and RX. and I can't connect to my wireless connection anymore. What should I doooooooo
View 1 Replies View Relatedhow to make dsl setup and to acess both wireless and wired at a time.
View 2 Replies View RelatedI currently have a computer sitting underneath a router/switch on a Local Area Network that I want to connect to the Internet using a 3G USB dongle modem. If I am connected to the ethernet and then enable the modem connection, only the ethernet LAN side works. If I enable the modem and then enable a (disabled) ethernet connection, only the ethernet LAN side works. If I keep the ethernet disabled and connect using the modem, I can get out onto the Internet, but obviously not the LAN. I need to be able to do both.
View 2 Replies View Relatedi'm running Kubuntu karmic and i've been using a 3G Huawei E1552 modem to connect to the internet, everything was going well when suddenly my modem stopped working. I've tried reconfiguring everything, i even reinstalled kubuntu from scratch with no success.Here's a part of my /var/log/debug
HTML Code:
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099883] usb-storage: device found at 7
Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099888] usb-storage: waiting for device to
[code].....
there are two computer
wireless internet accessible notebook.
desktop with no wireless card (but just normal lan card).
I connect two computer with lan cable, and I want to use internet in desktop computer through the notebook's wireless lan
what kind of setting do I have to do?
desktop's OS is Ubuntu, and notebook's one are Ubuntu, Windows XP.
I had an ATT "2Wire" modem/router that was working but connection to the Internet was often poor. An ATT technician came to my home and swapped out the modem/router for the identical model. I changed the ESSID and WEP code to match the new unit and everything was fine with the following wireless units: a wireless desktop, two cellphones, three wireless Archos tablets, and a couple of e-reader tablets. So all seemed to be fine wirelessly. However...
My laptop (SuSE 11.0, KDE3) simply won't connect no matter what I do. I changed the ESSID and WEP info in the lappy exactly as was done with the other wireless devices named above. But no good. The lappy does see the modem/router (a good, strong signal appears in KNetworkManager). But it seems as if the modem/router is rejecting the lappy's attempted handshake using the new ESSID and/or WEP information.
I thought that perhaps there was something wrong with the lappy's wireless card, so I took it to a Starbucks to see if it would connect there on an open network, and it did without problem. So the lappy's wireless card appears to be working fine. It just won't talk to the encrypted modem/router at home. Here are the settings on the lappy. Hopefully something here is easily identified as the culprit. With all the clicking I've done it certainly is possible that I ticked something that should not have been ticked and just don't realize what I've done.
Network settings screen:
Global options tab:
Network setup method: user controlled with Network Manager
Change default route via DHCP (ticked)
[code]....
Why won't the new modem/router which is exactly the same as the old one except for the ESSID and WEP work with my lappy yet it does work with a bunch of other wireless devices?
Just today I installed opensuse 11.3 on my Compaq CQ61. Even though I am able to connect to networks (both with an ethernet cable and wireless) I don't have internet access. I have used opensuse for a very brief period in the past and I had no such problem.
View 3 Replies View RelatedI have recently installed ubuntu 11.04 on my asus eeepc1005hab. And I've had problems with the wifi. I can connect via ethernet, but the wireless won't connect. I can see the connection, but my wifi never connects. I've tried many things but it still won't work.
View 9 Replies View RelatedI have 2 LAN ports. one from the motherboard (on board) and the other from a lan card i bought a few days back. one is use for browsing the net, the other for a media player.
problem is i cant connect to both the eth0 and eth1 at the same time. i have to disconnect one of them to connect to the other. and this really gets irritating as it doesnt always work as flawlessly as it should. what am i doing wrong?
Output of "ifconfig":
Quote:
I'm on ubuntu desktop 10.10 64 bit.
I recently moved to a student dorm in my university (RWTH Aachen) and I have an ethernet connection from my room. The thing is that I can't connect to the internet, I don't get any IP through DHCP. I tried using wicd instead of network-manager, and doing it manually with dhclient. None of those worked (actually I don't know much about how networking works so maybe I didn't do it well with dhclient). The weird thing is that Windows 7 gets the IP instantly and I can connect to the internet from windows. But I don't know why Ubuntu refuses to get an IP. Info from lshw, lspci:
lspci
Code:
sudo lspci -vv
02:00.0 Ethernet controller: Marvell Technology Group Ltd. Device 4380 (rev 10)
Subsystem: Sony Corporation Device 905e
[Code].....
I am using Ubuntu 11.04 and a Huawei USB modem to connect to internet. Most of the time when I start computer it is not detected my system. Then I use to reboot and then it gets detected automatically. That means its drivers are now loaded. But I don't know why drivers are not loaded when I start first time.
View 1 Replies View Relatedhow to connect my modem to the Internet, the help file on my Ubuntu 9.10 does not match the features available. I am using a modem from Starcomms (a local CDMA services provider in Nigeria) made by Epi Valley.
View 4 Replies View Relatedi wanna to connect to internet with USB DSL modem .
View 1 Replies View RelatedI am new in Ubuntu Linux. I am using Acer Aspire 4740. And I have purchased HSDPA Mobidata as internet modem. But I cannot connect it. How can I connect it and use internet using this modem?
View 2 Replies View RelatedI use Ubuntu i can not work internet connection Please help me search for a solution but did not find
Use the USB modem model x060s.
My laptop was on windows xp and when I installed ubuntu linux my NIC Card driver was gone (I think) and now I can't connect to the internet using an ethernet. I have the driver on the desktop of my Linux laptop but I don't know how to add it using terminal or any other options.
View 1 Replies View RelatedI am using Ubuntu Server version 10.4, and am trying to connect to the internet via an ethernet cable. This may and probably is incredibly simple, however, I could not find anything that pertains to it.
View 9 Replies View RelatedMy router malfunctioned after a weird lightning strikes scenario so i tried connecting directly to the modem, i cant connect on my ubuntu desktop so itried connecting using my laptop with windows 7 and gets connected
View 1 Replies View RelatedI currently using Ubuntu 10.04 LTS
View 2 Replies View Relatedi have E220 usb modem which i managed to crack and make it work on the Airtel network here in india.The problem is i cant seem to make it work in ubuntu, the way it connects is as below :
i boot in windows and connect to internet Then reboot in ubuntu and then it works fine.and i have to do this everytime. appears like the device gets initiated by booting in windows.
I have never connected to the internet using ZTE EVDO modem. I know it's being recognized but connection cannot be made.
View 9 Replies View RelatedI think I have configured GLink usb modem so far. But when I run wvdial command, I got the following. But I can not browse the internet. Other problem is when I try to use Gnome PPP dialer, it could not connect. Modem type is listed as ttyS0 and so on while I have setting in wvdial.conf ttyUSB0 so it does not support.
chitra@chitra:~$ sudo wvdial
[sudo] password for chitra:
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATE0
--> Sending: ATQ0
OK
--> Re-Sending: ATE0
OK
--> Cannot get information for serial port .....
--> Initializing modem.
My internet is provided by a 3g modem usb. I am sharing the internet connection through my desktop into a router and then to the rest of my Ubunut machines. Currently if I want to file share I have to go into the network manager and change the eth0 settings from shared to dchp automatic and then unplug the cable from the internet port on the router to one of the network ports. Is it possible to add another network card to the main machine and use that exclusively for either internet or file sharing.
View 2 Replies View RelatedI have a Toshiba Satellite L645D-S4030 running on Ubuntu 10.04. When I plug an ethernet cable into the ethernet port, simply nothing happens, and when I try to connect to my wireless network, it connects but there is no actual internet available. I'm sure the wireless works as I'm on an older model Toshiba Satellite and it connects fine (running Ubuntu 10.04 as well.) I tried to follow the procedure in the stickied thread, so when I type in these commands, here's what shows up:
Lspci
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge Alternate
00:01.0 PCI bridge: Toshiba America Info Systems Device 9602
00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0)
[code].....
how can i connect to the internet using modem card?
Intel d915,3GHz pinless,Lucent Modem
I am using samsung mobile (sgh-b220) in order to connect to the internet. I can easily connect on windows system , using PC studio software. I tried KPPP, wvidial none solved the problem. (It successfully dials the number. Put pppd connection will be terminated)
Some how I managed to scan modem communication taking place on the windows system, and tried exact commands on linux system still I am not able connect.
I have attached log files from windows machine. wvidial.conf, wvidial out put file along with this post.
I am unable to connect to internet using my cell phone(sony ericsson X1i xperia). When i connect from wired internet it connects without a problem. What settings should i change/ programmes to execute? Thank u in unticipation
View 3 Replies View Related