Fedora Networking :: Cannot Find Network Card While Setup Network Configuration?

May 25, 2010

Cannot activate network device eth0!"device eth0 does not seem to be present, delaying initialization".i cannot find my network card while i set up network configuration Now I use dual boot window 7 and fedora 9,I cannot find my network card in select network adapter while network configuration ,i have a network card Atheros AR8132 PCI-E fast Ethernet controller NDIS(620)and for wired in Accer laptop .

View 1 Replies


ADVERTISEMENT

Fedora Networking :: Can't Find The New Network Card

Apr 9, 2011

got a new MoBo today. dropped it in and powered it up to find no network connection. when I dig though network manager I find no network devices, same with "network configuration" lspci gives:

03:00.0 Ethernet contoller [0200]: Atheros Communication Device [1969:1083] (rev c0)

ifconfig gives just the "lo" device. is there a hardware detection step I'm missing? I should mention this is a swap of one onboard NIC for another.

View 6 Replies View Related

Fedora Networking :: Setup The Network Scripts To Create Two Network Interfaces For Vlan X And Y?

Apr 7, 2009

Using Fedora 10, can anyone tell me how to setup the network scripts to create two network interfaces for vlan x and y. Both interfaces should obtain an ip from dhcp and both interfaces should run over eth0.

View 2 Replies View Related

OpenSUSE Network :: Suse 10.2 Network Card ( DG41RQ ) Configuration?

Jun 19, 2010

i am using intel hardware on this working on suse linux 10.2 . i am not able to configure the network card IP address I have tryed using dhcp and static both way. Currently intel DG41RQ network card is assembled in my system. by using command ifconfig i can see only lo but eth0 is not displayed their.

View 4 Replies View Related

Ubuntu Networking :: 11.04 Management Of Network Card / Wired/wireless Setup?

May 1, 2011

I am facing a problem with the management of my network card after installing Ubuntu 11.04 32-bit Desktop edition.

There are two Network Cards and one USB adapter which I'd like to drive:

- Ethernet controller Broadcom Corporation NetXtreme BCM5703X Gigabit Ethernet (rev 02)
- Ethernet controller Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
- Realtek Semiconductor Corp. RTL8187 Wireless Adapter

Actually I need the wireless adapter to connect to the AP, so both of the ethernet card should be disabled. Infact, when I try to access to the AP I must disable the eth0 card by using (sudo ifconfig eth0 down), otherwise the route assigns the default gw (192.168.1.1) to the eth0 device and the network is useless.

View 2 Replies View Related

Networking :: Setup VMware's Network Configuration For Red Hat Can Access Internet?

Apr 7, 2010

I installed and tested both Windows server 2003 and Red Hat 9.0 with vmware workstation7. After installing 2003 can access internet but Red Hat can't. I want to test squid proxy server, send mail server, webserver etc. So, I would like to know how to setup WMware's network configuration for Red hat can access internet.

Below link is the configuration of VMware network setup both Server 2003 and Red Hat.

Here is Red Hat Configuration:
http://i64.servimg.com/u/f64/11/74/16/17/linux10.jpg

Here is Windows Server 2003 configuration:
[url]

I am using wireless connection to access internet.

View 1 Replies View Related

Ubuntu Networking :: Setup TFTP Server To Work On Secondary Network Card?

Dec 14, 2010

a machine with 2+ network cards, need to setup TFTP server on one card and use internet on another.

the tftpd server works on default routing network adaptor with following configuration.

How set the TFTP server on the secondary network adaptor?

TFTP server tftpd by xinetd configuration in: /etc/xinetd.d/tftp
{
protocol = udp
port = 69
socket_type = dgram

[Code]....

Could not find how to change the post <prefix> I remembered clearly I did before.

View 1 Replies View Related

Red Hat :: Networking - Setup Network Scripts To Create Two Network Interfaces For Vlan X And Y

Apr 7, 2009

Can anyone tell me how to setup the network scripts to create two network interfaces for vlan x and y. Both interfaces should obtain an ip from dhcp and both interfaces should run over eth0.

View 4 Replies View Related

CentOS 5 Networking :: Setup A Network To Network VPN Tunnel Between Our Main Office And A Temporary Location?

Aug 12, 2009

I am attempting to setup a network to network VPN tunnel between our main office and a temporary location. This location need full VPN access back to the main office's network.Anyhow we have spent about 3 solid days attempting to make this work without any great success. Here is our network scheme for these two devices.

Network A (Main Office) (OpenBSD using isakmpd)
Network: 172.16.8.0/24
External IP: 1.1.1.1 (obviously not the real IP)[code].....

View 2 Replies View Related

General :: Networking - Network Card - Connected To Network - Given Access Point - No Connection?

Apr 3, 2010

I installed the driver for my network card. iwconfig and ifconfig are all responsive to connecting to the network, I'm given an access point address. Then, I try to connect to a website and no dice. ping www.google.com yields no result. What gives?

View 2 Replies View Related

Networking :: Xen Network-route And Network-bridge Setup?

Aug 22, 2010

I've currently got a Xen box with 3 Virtual machines on it, in a routed setup. I'd like to put them all on a private internal network as well, which I'm assuming I'd do with a dummy network card and a xen bridge, but I can't find any information about setting up the xen Bridging setup on top of the existing network-route instlal.

View 1 Replies View Related

Ubuntu Networking :: Wireless Home Network Is Not Recognized By Network Card (RealTek RTL8190 Mini PCI)

Jul 12, 2010

my wireless home network is not recognized by my network card (RealTek RTL8190 mini PCI). The post was as follows: "I am using a new computer with Windows 7 , Athlon quad core 2.60 64 bit, 8GB RAM. Internet conection works fine with ethernet but ubuntu does not see my wireless network. card (RealTek RTL 8190 ID: 10ec:8190). Have searched this forum but unable to come up with a fix. I was looking for windows XP drivers to use Ndiswrapper but could not find a list of .inf files. My network is OK and works perfectly in windows and with my 2 laptops. Can anyone point me in the right direction? Additional info: install was done within Windows using WUBI to a separate partition on my HDD. I am new to this and thouroughly confused as to the procedure for installing the drivers if they are in fact available."

I am very frustrated in that I would like to use Ubuntu 10.04 but it is useless without internet connectability. I am new to linux and do not understand where to get the appropriate drivers or how to install them. I wish someone would answer this post and either give me a clue what to do or just say "give up" and uninstall ubunutu.

View 2 Replies View Related

Networking :: Cannot Find The Network Storage Drive On MS Network Using Ubuntu?

Dec 26, 2010

i can not find the network storage drive on my MS network using Ubuntu.i can find other computer using xSMBrowser but not the hard drive connected to my router (LAN)i have tried samba and a few others

View 5 Replies View Related

Networking :: Network Setup - Router - Wireless Router Card ?

Apr 24, 2010

I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.

Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.

Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).

The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.

Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).

Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.

Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).

My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?

Here is a link to (picture) my network diagram. Network Diagram

View 2 Replies View Related

Ubuntu Networking :: Broadcom Corporation NetXtreme BCM5721 Network Card Randomly The Network Connection On The Server Will Stop Working?

Jan 29, 2011

I have a Broadcom Corporation NetXtreme BCM5721 network card on my server at work.Everything works fine for a few weeks, then randomly the network connection on the server will stop working. After it stops working, I will try to reconnect with the network manager, it shows a wired connection available, it shows the "connection in progress"animation, then the "connection disabled" icon.

I uninstalled the network manager and used manual configuration, but do you think the network manager was the issue? I can't have the server disconnecting randomly every few weeks with no way to know what the real problem is. Was there an issue with the network manager with 10.04?

View 4 Replies View Related

Fedora Networking :: Network Print Setup

Jul 14, 2011

Fedora 15/Gnome3, latest updates as of 4pm EST 7/14/11.Trying to connect to a Canon inkjet printer, which is physically on a WindowsXP box via usb cable. Printer is made shared on the Windows machine.On the F15 machine, I can connect to all shared folders on the WinXP box via SMB.But trying to set up the printer connection from WinXP box to F15 is not working. I use Printing, then Network Printer, then enter the WinXP IP, then choose Find Network Printer. Note there's no CUPS or SMB printer choice - only AppSocket/JetDirect, IP, HTTPS/ and LPD. After a few minutes, I'm prompted to enter username and p/w for the WinXP machine, and the printer is located. Connection is verified.Connection is shown as Windows via SAMBA. I click OK and move to driver installation.

View 3 Replies View Related

General :: Pci Network Card Setup?

May 2, 2011

My name is Matt i've installed Redhat software on my PC using PCI network card.which command can i use to setup my PCI card to be the default network card?

View 1 Replies View Related

Fedora Security :: Switch Off The Network Interface But Light Of Network Card Plugged In The Router Stays On (green)

Dec 26, 2010

I have a laptop connected to the the net thru an adsl modem, when I switch off the laptop network interface,(thru system-config-network) the light of the laptop network card plugged in the router stays on ( green) where as in my pc, when i do the same thing , the light of my pc network card goes off in the modem

View 5 Replies View Related

Fedora Networking :: Two Network Card In One PC?

May 14, 2010

I just want know, how two network card in one PC working on fedora. I want try setup router + firewall on my PC. And i need tutorial how is working

View 1 Replies View Related

Fedora Networking :: Wireless-G USB Network Adapter Setup For 12

Jul 14, 2010

To setup a Compact Wireless-G USB Network Adapter (WUSB54GC) on Fedora 12 ?

View 1 Replies View Related

Debian Configuration :: How To Setup The Network

Sep 14, 2010

I've illustrated it on this picture, and hope to get the help i need to set it up... [URL]Thow it has to be furture secured, in that meaning it has to be abel to attach a eth2 on the main server, so i have 3 NIC's.Also, i want to have fully controll over ports, IP/MAC's and data overview (Such as a view of the files beeing downloadet/uploadet).

View 3 Replies View Related

Fedora Networking :: Two Network Interfaces - Setup Default Gw Route?

Mar 26, 2009

So I have two network Interfaces

eth0 - NAT behind a router
eth1 - Public IP

When ever I restart the machine, both interfaces pull a IP, but the it randomly chooses eth0 or eth1 to have the gateway. I want the gateway to be eth0 always.

[Code]...

Is there some file or setting I can modify in Fedora10 that will always choose 192.168.1.1 on eth0 as the default gateway?

View 2 Replies View Related

Fedora Networking :: Home Network - Setup One As Server And The Others As Client

Mar 29, 2009

how to setup a home network for learning purpose. i have two laptops and a desktop connected to a modem-router for broadband (wired connection), i want to setup one as server and the others as client.

View 2 Replies View Related

Fedora Networking :: Network Bridge Setup Disappears After Reboot

Nov 18, 2009

I am trying to set up bridge, and everything seems to be ok, except 1 thing, it disappears after reboot. So, what I am doing:

Code:
brctl addbr br0
brctl addif br0 eth0
and adding /etc/sysconfig/network-scripts/ifcfg-br0, here it is:

Code:
GATEWAY=192.168.1.1
DEVICE=br0
BOOTPROTO=none
NETMASK=255.255.255.0
DNS1=208.67.222.222
DNS2=208.67.220.220
TYPE=bridge
HWADDR=00:18:f3:75:18:78
IPADDR=192.168.1.3
IPV6INIT=no
ONBOOT=yes
USERCTL=no
and my ifcfg-eth0 is:

Code:
GATEWAY=192.168.1.1
DEVICE=eth0
BOOTPROTO=none
NETMASK=255.255.255.0
DNS1=208.67.222.222
DNS2=208.67.220.220
TYPE=bridge
HWADDR=00:18:f3:75:18:78
IPADDR=192.168.1.3
IPV6INIT=no
ONBOOT=yes
USERCTL=no

How to make it working after reboot?

View 1 Replies View Related

Fedora Networking :: F10 And Trendnet Wireless Network Card

Sep 8, 2010

I know that most people are using F12 and F13 but I just installed F10 on one of my machines. The Kernel is 2.6.27.5-117.fc10.i686 and the GUI is Gnome 2.24.1.I have a Trendnet wireless card already installed in the machine from when it ran XP which is in the tew-421pc/tew-423pi family. Is there a device manager/hardware installer that I can use to set up the wireless card or does anyone know of a driver install program for this card?

View 1 Replies View Related

Fedora Networking :: F14 - Can't Find Network (wired Or Wl)?

Feb 28, 2011

Issue: Using Fedora-14-x86_64-Live-Desktop.iso, I created a live usb and tried it on Dell M6400. I can boot into F14, see the internal hard-drive and other usb drives -- but F14 will not go on the network -- neither wired or wl networks.

I am not sure what additional information I need to provide to help resolve this issue. Perhaps some background info would help?: I am trying to move from XP to linux on the M6400. The latest Ubuntu live CD would not boot, the latest CentOS live CD could not find the internal drive; I got best results with the latest Fedora (and I am more comfortable with the F14 gnome interface than the F14 KDE, the Ubuntu, and the CentOS interfaces). I do not know how to investigate the inability of F14 to detect the ethernet cabled network. I was unsuccessful in my attempts to get the wireless to work: "lspci -nn" shows BCM4322 802.11a/b/g/n 14e4:4326 (rev01). I read [URL]../docs/linux_sta/README.txt and used what I learned in my attempts. Installing broadcom-wl-5.60.48.36-1.fc13.noarch.rpm, kmod-wl-2.6.35.6-48.fc14.x86_64-5.60.48.36-2.fc14.2.x86_64.rpm, and kmod-wl-5.60.48.36-2.fc14.2.x86_64.rpm (found at rpmfusion) did not help. I tried to build and install the sources from http://www.broadcom.com/support/802.11/linux_sta.php; the machines I had for building were 2.6.28-18-generic Ubuntu, fc5, and rhel5 -- attempts with these builds failed too.

View 5 Replies View Related

Fedora Networking :: Network Configuration In VirtualBox

Jan 27, 2011

I have Fedora 14 installed in VirtualBox, running in MS Server 2008.There is Oracle 10g software installed in Fedora 14.How can I configure connection to Fedora 14 from MS Server?Anything I've done is useless.I need to open port 1521.I can ping Fedora from MS Server. I can make connection "telnet localhost 1521" succesfuly in Fedora. But that's all.

View 1 Replies View Related

Fedora Networking :: Wireless PC Card Not Connected To Any Network - Driver

Dec 22, 2009

I have a Netgear WG511GE PCMCIA card, and a driver from the original installation disk. I used an ndiswrapper-utils gui called ndisgtk to install the driver. I then do the following to verify an installation:

[Code]....

Unfortunately, when I put the PCMCIA card in, nothing happens. On Windows, a green light flashes even if the card is not connected to any network. At first I thought this might be a hardware issue, so I did #lspci and got:

[Code]....

Lo and behold, when I put a different unbranded Wireless PC Card in it works. I'm no expert in Networks, but to me this suggests a driver problem (i.e. the card is physically detected it just won't work). However, the correct driver was installed with ndisgtk and this was verified with #ndiswrapper -l, hence the confusion.

I'd be grateful if anyone else has had this problem/knows of this problem and is willing to share the solution with me/point me in the right direction. So far, Google has returned a few posts from a few years ago talking about patching kernels and manually building files etc (just before Prism54 became integrated into the Linux kernel).

View 8 Replies View Related

OpenSUSE Network :: Can't Find Network Hard Driver On Network?

Oct 31, 2010

On Linux Mint (Gnome) i used to go to Network drive. that is on the right hand side of Nautilus there is a short cut for Network. in there i could see my network hard drive and other laptops connected to the network, and i could access my files. but on OpenSuse, when i open the network folder, nothing comes up. may be it needs some sort of configuration.

View 2 Replies View Related

Debian Configuration :: Setup A Bind9 Server For Home Network?

Mar 4, 2011

I'm trying to set up a bind9 server for my home network, I have all my IPs set to 10.0.0.X. I would like the forward and reverse to be simply "machinename", not "machinename.domain.com", as I don't want to type a domain everytime.

In my named.conf
zone "net.local" in {
type master;
file "/etc/bind/net.local.ns";
allow-update { none; };

[Code]...

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved