i configured my laptop (running UBUNTU 10.04 LTS) for my broadband (bridge mode). I did that using PPPOE CONF command. Everything goes ok but only prob is i have to run this command and configure my net every time i restart my system. What i need is it should connect to the net whenever i use the PON DSL-PROVIDER and must turn off by using POFF..
View 1 RepliesMy network is windows pppoe. How can I configure it for Fedora 11? Is there any graphical configuration tool available for that? Also, ubuntu 9.04 logs into pppoe network after restarting as I've made some changes in /etc/network/interfaces. Is there any option available for Fedora 11 to automatically log in to pppoe network after restarting?
View 4 Replies View RelatedI have wireless adapter USB rt1878 working fine.I have to setup pppoe to make internet connection?I need this help?
View 3 Replies View RelatedI have wireless adapter USB rt1878 working fine.I have to setup pppoe to make internet connection?I need this help?
View 1 Replies View RelatedI am deployed to Iraq and the Earthlink ISP here uses PPPoE to configure a connection to their wireless broadband. His english skills are pretty good and from what I gather, he's got a DSL connection that he's trying to connect me to. He showed me how he does it on a Windows machine but I can't figure it out on my ubuntu laptop. That windows machine didn't need any IP addresses or server names. It only used a username and password to connect. Of course a strong wireless signal detected was also pre-requisite.
I know my laptop works because I've had great success with it here lately, just not on the Earthlink service.I see their wireless is broadcast and I can connect to it. I just can't figure out how to post my credentials and authenticate.I don't see a way of entering my username and password because I don't know how to install (or configure) for PPPoE.I did use the pppoeconfig and got to the part where I add my username and password, but most of what's going on up to and after that, I do not have the knowledge base to use. So I figured that allowing the defaults and recommended settings would be acceptableYou'll have to forgive me if I've asked another dumb question here. I'm another one of those Linux enthusiasts who is learning and I'm just not willing to switch back to MS just to get internet while deployed.
I have an internet connection which requires pppoe setup to login with the specified username and password ip address is dynamic.Above are the screenshots for your reference for which I establish the internet connection.the pppoe settings can be done through "sudo pppoeconf" but for the screenshot No. 2.what is the procedure? I need to specify the service name for my internet connection.how to configure my internet connection.
View 8 Replies View RelatedI've been trying to use gnome-schedule to create a scheduled task that would dial my pppoe connection automatically. For this I used "sudo pon" command (after configuring the pppoe connection using pppoeconf ). Although the command gets executed, but then it waits for me to enter the password. I want it to be automatic & shouldn't require me/anyone to authorize it. Is there a way to enter this password automatically for the scheduled tasks?
Also, I'd like to use network manager, instead of pppoeconf, for the same purpose. How can I set network manager to dial a pppoe connection at scheduled time?
i can't get a pppoe conection working over a wireless network,in windows I have to connect to the router first, and then put in my user and password to get connected, but i don't know how to do this on fedora, i get connected to the router through network manager, and ping is ok, but when i try to make a new xDSL connection i don't know how to make it work through the wireless network that is established and working with my router.
View 9 Replies View RelatedI need to get my printer assigned to a hostname "myhost.dyndns.org". What do I need to configure in the cupsd.conf file to put it online?
View 1 Replies View Relatedi have a routed and a PPPoE type internet connection, recently i tried a thing in terminal with the pppoeconf option since the network manager has problems with connectiong to the internet with a pppoe DLS connection, or anyway in my case it does not work. Ok i did the pppoeconf thing i inserted my pass and my user and left the program to do its thing, ok it all worked fine but then i restarted my system and suddenly the network manager did not want to recognize my network it hat as options some weird ipupdown options for connection and when i tried the pppoeconf thing again it did not work. what could i do to reactivate at least one way my connection, if i understood correctly the terminal type connecting and the network manager are two different things. now i am using my router and it should connect but the network manager still does not see the connection.
View 3 Replies View RelatedI cant get my wired internet connection to work. The command 'dpkg -s pppoeconf' returns ' installed ok installed'. My connection is through a router which is probably in a semi-bridge mode and I need to dial a connection to get the net started. The connection Auto eth0 is setup properly with the correct cloned MAC Address (that of my laptop).
I've also executed 'sudo pppoeconf' and ran the whole series of steps which towards the end said that my connection will be set on boot. However, the net doesnt work directly and I dont know how to dial manually either. 'sudo ifup eth0' returns 'interface eth0 already configured'. I tried some 10-15 threads but none worked. Ubuntu is handicapped without internet.
ver: 9.10 how do I restart dhcp3 after changing dhcpd.conf?
View 3 Replies View RelatedI am trying to use SWAT to better configure Samba.conf I have swat installed and working but it is missing the GLOBAL button which is its main configuration tool?
View 3 Replies View RelatedI am using Squid server on my Red Hat Linux machine.Squid is functional and clients are access through proxy.I want to ask that if I want to open my squid.conf file for any changes should i first stop squid and then do the changes .
View 3 Replies View RelatedI would like to know how to configure a pppoe connexion? I am testing version 11.2 on live cd but I can't manage to connect my laptop. I used the "green plug software", I filled all the blanks (I am not a total beginner because I have been using Mandriva for a year) but afterwards I can't select pppoe instead of eth0 What should I do?
I read on this forum NET INSTALL PPPOE - Alionet, communaut francophone d'entraide openSUSE et SUSE Linux that the only reason that I can't configure a pppoe connexion is because I am using a live version of 11.2 as result that it only recognizes an ethernet connexion and a modem (everything I said, is said in the forum I linked, but you'll have to read it in french )
I try to configure a pppoe connexion to Tl2, my internet connexion provider. I live in France. My modem is a Bewan ADSL ethernet 100, no need to configure it.
I am having occasional internet connection problems on startup. 1 out of 5 times that I start my computer, I will have absolutely no internet connectivity, can't ping my router, obtain ip. nothing. Tried re-establishing connection with no luck. Status light on my router displays a slow flash. I restart, problem solved. Not so much a major problem, but irritating at times
View 1 Replies View RelatedDell atitude E6420. e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 Firstly, I installed 11.04, 64 bit, I have wired internet but can not restart; then I switched to 10.04 LTS 64 bit, I can restart but I lost my wired internet. For both situation, wireless internet works well. I update the "linux-image-generic-lts-backport-maverick", then the wired internet works, it is fine. But, I can not restart the system, just same as 11.04. How to fix it?
View 2 Replies View RelatedI am having a problem with my internet connection. It only works half the time. Usually when i start the computer it doesn't connect until i restart anywhere from 1 - 10 times. I did sudo ifconfig while it was not working here is the output:
eth0 Link encap:Ethernet HWaddr 00:19:d1:00:36:41
inet6 addr: fe80::219:d1ff:fe00:3641/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:11 errors:0 dropped:0 overruns:0 frame:0
[Code]...
Like the title says, is there a way to restart the computer if the internet connection is lost?Is this possible on ubuntu?
View 3 Replies View RelatedLast week I attempted to get "up to speed" with my Comcast cable connection... Ubuntu 9.10, Dell Vostro 400 desktop, Firefox 3.6.13... Comcast says I should have 12 Mbps connection... if I get 1.0 Mbps, I'm doing good... they just tested everything, and said everything is fine on their end. They use [URL] and connects to a server in Chicago, 60 miles away. That gets fantastic speeds, and it's a durn shame the internet doesn't store all its files there!! I use [URL] for my tests, and it uses a server in Dallas TX.
I go to my girlfriends house, and her AT&T DSL line has d/l speeds of 4.5 Mbps or better!!! She's running XP Pro on a Dell machine. So, started digging on the web and thru the forums, and found this:
[URL]
But, like ALL too many things, it's dated... it's from 2008... I've set my settings to what is there, and disabled ipv6 in Firefox. Hey, now, I'm sometimes up to 1.4 Mbps!! Also found this, but no date...
[URL]
Reading forums, I see that folks have said there is a network connection problem with 9.10... and then I see that others are saying the same thing about 10.04 and 10.10!! I have 10.10 on my laptop and had to fight to get its Atheos card to be recognized. Running some tests [URL] gives me weird results: Download 2.64 Mbps, Upload 4.12 Mbps. NOT what it should be. Similar results from testmy.net.
Dunno exactly what info is needed... Speedguide.net gives me results below, but I've tried changing numbers (says my RWIN is low) and nothing changes:
--------------------------------
TCP options string = 020405b40402080adf1dca100000000001030306
MTU = 1500
MTU is fully optimized for broadband.
[code]....
So, today, find, once again, that I'm d'ling in the range of 90/KB/s (719 Kbps)... disgustingly slow. I go on my HP laptop and run the test, and it says 1.6 Mbps. So, desktop directly connected to router is not even 1 Mbps, and wireless connection is faster? Neither of which is close to what I should be getting...
Since the upgrade from Lenny to Squeeze on my Notebook Toshiba Satellite Pro U200 with Intel Pro/Wireless 3945 ABG I have wireless connection problems.The connection breaks time to time and sometimes cannot connect automaticaly after restart. BTW I didn't change anything on the wireless or network configurations on the notebook and on the wiereless router.
View 8 Replies View RelatedI have a machine running Karmic sat in the corner of my office. I scp stuff from my mac to it quite a lot over my local wireless network.At the moment, it holds a .sparsebundle backup of my mac created by SuperDuper! (mac backup application) that I periodically transfer over. I'd like to make this system a little more sophisticated and use Apple's Time Machine to automatically backup to my Ubuntu box if possible.
Anyone have any experience of this? I'm kinda hoping for something a bit more straight forward than this: http:[url]....
I have problem to access the Internet, with Ubuntu 10.04. In Windows I access the Internet in this way: Create a PPPoE Connection (with username and password), after this connect to a Wireless Network called WebSTAR (I have Wireless modem in my family PC), and connect to PPPoE Connection. After these steps the Internet works fine. .But I have same problems with Ubuntu. First I see the Network named "WebSTAR" but I can`t connect to it. And I try many times to join the Internet with "sudo pppoeconf" command in Terminal, but didn't work.
View 2 Replies View RelatedI have a linux box (fedora) with two ethernet cards eth1 and eth2. On eth1 I successfully configured a PPPOE internet connection. Such that from the server I can browse the internet. On eth2 I wired it to a wireless router essentially to provide the wireless cloud. On eth2 I also configured dhcp, such that the Linux box is both PPPOE and DHCP server.However my clients on the LAN cannot access the Internet.
On passing the routing command I get
Destination Gateway Iface
196.44.x.y 0.0.0.0 ppp0
192.168.1.0 0.0.0.0 eth2 (my subnet)
0.0.0.0 0.0.0.0 ppp0.
The router (functioning as a wireless access point mainly) has a fixed IP address of 192.168.1.2 and eth2 has IP address 192.168.1.1. The dhcp file running on Linux has been set with option router (Gateway) 192.168.1.1. I cannot figure out how to correctly set the routing table such that my clients on wireless can access the internet cloud. I googled and googled but no solid solution. Any suggestions?
I finally managed to install pppoe and pppoeconf. When I type command 'pppoeconf' , it invokes some window and I put username, passwd etc. But my net connection won't start. I have posting the output of various commands related to networking.ifconfig
Code:
eth0 Link encap:Ethernet HWaddr 00:0f:b0:4a:54:a7
inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20f:b0ff:fe4a:54a7/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1388 errors:0 dropped:0 overruns:0 frame:0
[Code]...
I have trouble connecting to internet when connecting using pppoe-start, even though it says it's connected and the pppoe interface is there. I test the connection by sending a ping to a known IP address and got "destination unreachable".
View 2 Replies View Relatedi run into a very annoying thing, usually take less than a second to connect to the internet using pppoe-start but today after a new installation of slackware 13.1 take a couple of secs to connect.
now:
# pppoe-start
Connected!
usually:
# pppoe-start
. Connected!
i'm using kernel-generic-smp-2.6.33.4, i even rebuilt the rp-pppoe package but it's the same thing. same behaviour was also in the previous release using kernel 2.6.29.6 due the broken forcedeth in that version of kernel, but on ArchLinux using the same version of kernel works normally.
I have install ubuntu 9.10 on my Dell studio, I have local broadband connection with its user name and password which i use to connect internet everytime i need along with its IP Address, subnet mask, Default gateway, Preferred DNS server. Where should i put all this details to connect internet, i have already tried with Network connection in System -> Preference . It all work well in window
View 9 Replies View RelatedI m new to Linux and I wanna to configure DSL modem wired connection in Ubuntu Please help
View 2 Replies View RelatedI have a ppoe internet connection. I was easier and faster to configure it in Yast than in Windows XP. When
The provider here sometimes goes through some problems and the connection may disappear and return at any unexpected moment. In Windows there is a icon on system tray that dysplays such information and I know when the connection is gone. It also allows me to try to reconnect manually. Where do I find these information on Opensuse here do I manage to reconnect. In Windows it was also possible to set the connection to re-dial automatically when it was out. It was very useful if it failed in the middle of a download, the system reconnected and the download manager retried until download resumed. Is there some way to adjust opensuse to reconnect automatically when connection fails or some software that does it? Furthermore, is there a good download manager that works in Opensuse that pause, accelerates downloads and retries when connection fails?