Networking :: Setup VMware's Network Configuration For Red Hat Can Access Internet?
Apr 7, 2010
I installed and tested both Windows server 2003 and Red Hat 9.0 with vmware workstation7. After installing 2003 can access internet but Red Hat can't. I want to test squid proxy server, send mail server, webserver etc. So, I would like to know how to setup WMware's network configuration for Red hat can access internet.
Below link is the configuration of VMware network setup both Server 2003 and Red Hat.
Here is Red Hat Configuration:
http://i64.servimg.com/u/f64/11/74/16/17/linux10.jpg
Here is Windows Server 2003 configuration:
[url]
I am using wireless connection to access internet.
MY OS IS (Widnows XP ) I'm Using VMware Workstation 7 to run My BT4-Beta (backtrack 4)
in my OS Windows XP I have Internet I'm in big network our administrator using Cyberoam Client for Corporate to allow people using Internet.. so if any people connect this network they should has id in Cyberoam if they don't has id will can't connect to the internet.. they will redirect automatically to the log in page in Cyberoam.
So ! in VMware Workstation 7 i configure network adapter to Bridged and i see internet icon with green color but dose not browse internet and also i can't ping my computer this is mean network dose not appear to backtrack my computer is in the network when i try to do ping this is what happened.
And this output to try run network!
PHP Code:
And this is my ifconfig
How to do Step by Step to connect the network using VMware WorkStation!
I have a WindowsXP virtual machine which I need to isolate from the host machine completely (have the host act as a bridge but not be visible on the IP layer at all.) It still needs to have Internet access. Obviously it has to be able to contact the router but I would like to be able to block port 80 (or even just block all SYN packets addressed to the router.) I also want to allow port forwarding from the router to the virtual machine. I can use basic iptables but this is way beyond me.
The host OS is probably going to be Debian Lenny but this is not built yet so if someone can recommend a different distro which is as lightweight as possible but will support VMWare, iptables and tcpdump then that would be great. I was thinking of Slackware but I have not used it in ages and from what I can remember their is no real package management.
Today, I have an ADSL box which is my gateway to internet (192.168.0.1).
I have a Raspberry pi (RPI) which I use as a dhcp & dns server (192.168.0.2).
Recently my mobile phone operator installed a 4G antenna beside my home, and the bandwidth and latency are much better with my mobile phone than with my internet provider (ADSL).
I would like to install a wifi dongle on my RPI (I would get wlan0 & eth0 interfaces)
When RPI detect my shared phone connection (tethering) I would like RPI to automatically route internet:
- from authorized devices on my network to my mobile connexion (wlan0 -> mobile phone). - from other devices to the standard ADSL internet (eth0 -> ADSL box).
I don't want any device to use the shared 4G connexion, best would be authorized devices to be selected by MAC address. How I should properly setup such a network ?
I'm trying to setup a wireless AP with my old asus eeepc, so it can act as a repeater to connect my android device on the other end of the apartment. I've already created the Wireless Access Point using hostapd. It took very little configuring, just changed from mode 'a' to 'g' and changed the channel from 60 to 1 and It was all set. Next I setup a dhcp server. Also simple enough using yast.
Up to this point, I was able to connect my android device to the newly created wireless network. However It doesn't have internet access. I guess I have to configure iptables for this, but I find it incredibly confusing! Here are a few specs to help with any examples: The laptop is connected to the internet through eth0 with IP 192.168.2.120 Hostapd is using wlan0, and I'm pretty sure it created mon.wlan0 So, to sum up, when I connect my android device to the network I can, for instance, see what ever pages apache is currently serving on the laptop, but can't access the internet.
Cannot activate network device eth0!"device eth0 does not seem to be present, delaying initialization".i cannot find my network card while i set up network configuration Now I use dual boot window 7 and fedora 9,I cannot find my network card in select network adapter while network configuration ,i have a network card Atheros AR8132 PCI-E fast Ethernet controller NDIS(620)and for wired in Accer laptop .
Running Ubuntu 9.10 Ive just got my wireless connection working after first having got the wired eth0 connection working.
With the wired connection I could SSH into my server through my firewall/router (via a forward). I can run up VNC, from there firefox, browse the web - all is well.
I have now setup the wireless connection, using a static IP, and I can likewise SSH into my server. I can run up VNC. I can ping my router. I can log onto it via VNC. I can browse to my router. But I cant browse the internet.
But I cant ping google.com. The reason is there is no host lookup service. Nslookup eventually says no servers could be reached.
So specifically, if I ping www.google.com Im told "unknown host". If I do an NSlookup on it I get timeout, no servers could be reached. However if I ping 66.102.11.104 I get responses.
I see no relevant entries in my firewall log.
Unfortunately I cant traceroute because the package isnt found - and of course I cant install it because I have no internet !
Strangely (to me at least !) if I then tunnel through SSH and browse the web, I have no problems. It works ? I know I am browsing through my SSH tunnel because whatsmyip gives the IP of my router at home, not where Ive SSHd in from. I can surf just fine.
why I cant do host lookups any more (and this did work with my wired connection, but whether its related to my change to wireless, or static IPs or both I cant be sure - it certainly appeared to happen at the same time). And, more to the point, what I need to look for/do to rectify it ?
As a bonus Id be interested in why I can SSH and browse via tunnelling but not direct from my server (via VNC). Just for interests sake !
if config reports :
wlan0 Link encap:Ethernet HWaddr 00:90:4b:27:ae:17 inet addr:192.168.1.69 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::290:4bff:fe27:ae17/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
I would like to set up a user account with no network access. Reason is that sometimes my little daughter plays with the computer (for example watching movies on dvd's) and I want to prevent internet access in case she plays unattended. Is there a simple way to do that? I am using ubuntu 10.04.
I have 1 root-server with 2 NICs, both having their own internet IP addresses:
Code: eth0 = 8x.x.x.183 eth2 = 8x.x.x.205 We only have one gateway on that network: Code: gateway = 8x.x.x.1 We want to use eth2 for postfix + http, and eth0 for all the other stuff.
How can this be setup ? With route / ip route / iptables ?
I can connect to my access point to surf internet. I setup my Dlink access point (password, network name, etc) in Vista by visiting "http://dlinkap/" in my web browser.
In ubuntu, I can connect and surf the web/internet but i cannot access the setup page.
When I try to type the "http://dlinkap/" to my browser then the browser will redirect it to google search.
I try 192.168.1.1, I can access my linksys router. but my dlink access point, i cannot access the setup page.
There is 2 networks that I would like to be part of
a) Through my wlan0 --> Internet DSL
and
b) Through my eth0 --> WUG - PTAWUG
I can only get one of the networks to work at 'n time. The wlan0 works fine when I start my PC, but when I want to access the WUG I need to do the following command:
with the above command, I can then access the WUG but not the internet through my wlan anymore.all data goes to my wlan as standard unless its on the 172.16.0.0 network
I want sound and internet access thru Linux using VMware. It will give me confidence to add it as a dual boot to my hard drive. I have sound and internet access thru Windows 7. I have sound thru the sound card test but I'm not able to hear cd's. I see the time elapsing thru the cd player but no sound.
I'm having problems with the network configuration, I get the message, "cannot activate the device etho:1 no link found". I have a DSL connect thru windows. Shouldn't I be able to get the internet thru VMware? If so how?
I want to connect to a wireless open ad-hoc network to have internet access. It worked a while ago (1/2 year or something) but some update must have messed something up so it doesn't work any longer. Situation: There is a laptop that is running windows 7 and is connected to the internet via cabel. A open ad-hoc network is configuered with sharing of internet connection, status of the ad-hoc network is "waiting for users to connect". I want to connect with a second laptop that is running ubuntu 11.04. I can find the network and connect to it.
Problem: I cannot get any internet access while being connected to the ad-hoc network. So my questions are: how can i find out if what causes the Problem? I suspect a driver issue, but I'm not sure. required information from Howto post a wireless issue:
I am attempting to connect Ubuntu 9.10 to the Internet.I have a network connection, and Karmic detects it fine. I can ping addresses within our network (e.g. the Windows computer in the next room), and I can ping the router, but if I ping, say www.google.com, it says "Destination Net Unreachable". Previously, in Jaunty, I had a similar problem.I found a workaround: launch Pidgin. Somehow, launching Pidgin temporarily edits my configuration. However, in Karmic, I have no access to Pidgin, however, and Empathy does not do the same thing. Since I have no Internet, I cannot "sudo apt-get install" anything.How can I get the Internet working?
if i'm connected to my wireless network it only gives me internet acces for a few minutes. The connection with my network stays but i have to close it back of and reconnect before i get back online.
I set my Network Adapter to the NAT setting, and ran an ifconfig for my machine. All the I got back was eth0 and lo. eth0 has the static IP configured I configured back in the days where I was running my VM Bridged with DHCP. Do I need to reconfigure my eth0 settings now and if so how?
We are in the process for Integration Network with our Government Network. Let say that our network are 192.168.0.0/24 And the Government network are 10.0.0.0/8 I want to know if the local network can resolve the internet names in Government Network. I am using Bind for DNS.
Background infoMy laptop (MySN MG6.c) is dual-booted with Windows 7 and Ubuntu 9.10, and connected to the internet through a router (Digitus DN-11004-O), which is set-up to use DHCP. The internet connection works fine under Windows, and my previous laptop, which also ran Ubuntu 9.10, had no problems connecting to the internet through that router.The network adapter is an Atheros AR8131 PCI-E (also detected as Attansic under Ubuntu)stem infoResults from running various diagnostics (I have removed the output that relate to the wireless connection, as I don't use it):
Code: $ uname -a Linux valyria 2.6.31-14-generic-pae #48-Ubuntu SMP Fri Oct 16 15:22:42 UTC 2009 i686
I'm trying to configure internet access using KDE network manager. Added new VPN pptp connection, set gateway and other options but manager tries to connect for about a minute and breaks then. Here is /var/log/daemon.log
Code: Jul 1 17:35:22 dvinokurov-desktop NetworkManager: <info> Starting VPN service 'org.freedesktop.NetworkManager.pptp'... Jul 1 17:35:22 dvinokurov-desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' started
[Code]....
As I understand the main problem is in "(IP Config Get) timeout exceeded".
Configuration: Kubuntu 10.04 x86, VPN server with MSCHAPV2 auth, no compression, no encrypting.
I have had a heck of a time trying to get my laptop running ubuntu to connect to my home network. I have managed to get it to work at my university which would seemingly be more difficult than getting it to work at home, so I know for a fact it isn't a hardware or driver issue. If I try to connect via ethernet cable from my router, it detects that I connected the cable but says "disconnected" and never lets me connect. If I SKIP the router and go from my modem directly to my laptop via ethernet cable it works great.
Using the wireless network tool I can see all of the wireless connections in my area. When I go to connect to my network it prompts me for the WEP key and when I enter it and hit connect it just keeps cycling and eventually times out and finally again prompts me for my WEP key. I know this network works as it works just fine on my Windows 7 partition. Another interesting note - both my wireless and ethernet connections both worked flawlessly and stoopid easily on the live cd but don't after the full install.
If I manually enter in the information for my wireless through IPv4 settings and enter in the Address,Netmask and gateway I can connect to my network - but then I have no active internet connection. Same deal with my wired connection. Is this because choosing this manual method grays out the DHCP?
I am trying to connect to the college campus wifi network, but having difficulties in Linux.I am dual-booting Windows 7 and Ubuntu 10.10, and I use Google Chrome web browser on both. When I boot into Windows, my laptop connects to the network (as I can see from the taskbar icon) and I can (and currently am) connect in Chrome.However, in Ubuntu, it connects (or so the icon indicates) but Chrome doesn't load any pages.The campus network is unsecured, but once you open the browser, you are prompted with a log-in page (student ID and password) to actually connect.Here is my output for iwconfig:
Code:
wlan0 IEEE 802.11bgn ESSID:"sjsu_campus" Mode:Managed Frequency:2.412 GHz Access Point: 00:24:6C:BC:D3:E0 Bit Rate=54 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off
Okay, a couple of weeks ago I was running 10.04, got an auto update that needed a firefox restart, so rather than restart, I just shutdown the computer for the weekend. When I booted the computer on Monday it would find sites (www.google.com, start.ubuntu.com) but it wouldn't download the necessary items to load the page. Now I have a windows laptop sitting next to the ubuntu box and it was online with no issues, so I know it wasn't the connection itself. So I decided that the update messed up the system so I downloaded 10.10 and installed that and ran that all last week.
On Friday I got a system update that required a firefox restart, so I ran firefox for the day and decided that since it was friday, I would just shutdown the computer and reboot on Monday.Well now Monday is here and now I again have sloooowww internet, to the point that URL.. times out and won't come up. I have tried doing a traceroute on both machines and the windows box gets all the way to www.google.com, but the ubuntu box gets about halfway there and then gets no response. I am at a loss, I don't want to reinstall every week. I did try to reboot and run the previous version of 10.10 that shows in the boot menu, but that does the same thing. One thing I did notice is that the broadcast ip is different than the machine IP, don't know enough to know if this is a problem.
I have installed Fedora 8 on an old PC to use as a home network and I am having trouble getting a Windows PC running XP to get through to the internet, but I am able to access the internet from the Linux box with no issues. I can ping the gateway on eth0 from the Linux box, but I can't ping it from the windows PC. I am able to ping the IP address for eth0 from the Windows PC. My internet gateway is a modem/router from Hughes net. I also have a Netgear router between the Linux box and the Windows PC, but there doesn't appear to be any issues because I can ping both NICs from the Windows PC. I have pasted my Linux NIC config below. code...
I have installed VirtualBox on Ubuntu 9.04.Two Guest Machine Fedora 9 and Fedora 11 is installed on the same. I selected NAT as Ethernet Interface and now I can see 10.0.2.15 and 10.0.2.15 as the both interface address in eth0 respectively.I can ping google.com and working.Now I need to make fedora 9 as server and fedora 11 as Client. How Can I make them in same network.I cant see Bridge Network anywhere only NAT, Host Interface, Internal Network..are available.
I have annoying problem. My setup is the following: debian Linux, 64 bits, VMWare workstation 7 host, with Windows XP running as guest. From Firefox, or Internet Explorer, I am unable to access few sites, for example nvidia.com, osdir. Basically get connection timed out, on the other hand ping works to those sites. Moreover, Slashdot loads very very slow and sometimes gets horrible text-only version.
everything works fine on Linux host
I suspect it has something to do with routing on Linux, I recall having similar problem long time ago, which was fixed by setting something in /proc.
I tried setting MTU and TCP window size on Windows lower, but did not help
I have a fedora 10 box with two network card on eth0 I have a pppoe connection to the internet, on second card eth1 I share my internet connection end I set up a samba server but I don't know if the settings are good. How to do this settings right to work fine, the ip are assigned by dhcp I don't use any static ip .When I try to browse the internet from the other computers some site's like {.com ; .org ; .info} are block, other site from {.ro} are working. Someone tell me something about turn off all my filters, but I don't know where to find this filter to turn it off. And when I use samba I can't have and internet access or vice versa. My network look like that:
I have a wired lan at home with 2 XP boxes connecting to a router to a DSL modem. I want to network my laptop, running only fedora os, for file sharing, printing and internet access. I will be using the laptop probably exclusively for creating/maintaining a Drupal-based (LAMP) e-commerce site to replace our old one for our small family business.
can't access internet. The up and down icon appears by the network connection (upper right hand corner). When I review connection properties, I see that the computer has a valid address, subnet, gatway, dns, etc... But it still can't connect to the internet. I can't ping external addresses either. But I can access internal addresses (local router).
