Red Hat / Fedora - Setup Lan And Wan Etho Cards
Apr 22, 2010
Wan (mail) is by way of wireless internet into a linksys (PPPoE) 192.168.1.1 router and then only to the mailserver into etho0 192.168.1.3. Mailserver also has etho2 192.168.1.2 connected to a switch that has 3 pc's attached and an adsl router for pc internet access. Server does not provide proxy for pc's. Just mail. Linksys is 192.168.1.1 and can be seen by the isp provider. The server wan is 192.168.1.1 and can ping to 192.168.1.1 and can browse the net via linksys. The lan connection is 192.168.1.2 and this should be visible to the pc's but it doesn't appear to be and can't ping a pc although the switch lights show it is connected.
etho0 192.168.1.3, 255.255.255.0 & default gateway 192.168.1.1
etho2 192.168.1.2, 255.255.255.0 & nothing for default gateway.
DNS is blank for hostname and primary dns is 192.168.1.1. secondary, tertiary and dns search path are all blank. Should there be a default gateway for etho2 even though it only has a lan connection ? If I gave it the adsl gateway then how would the server know which card to use for outside access?
View 6 Replies
ADVERTISEMENT
Dec 10, 2010
I'm not able to set up eth0 with a static ip adress.service network restart and it was okkay but when I try to turn off and turn on, the ip adress is set up with dhcp.
View 7 Replies
View Related
Oct 8, 2010
I am trying to setup a 5 monitors setup using 3 cards, but I am stuck at 3 monitors for now. The third card is not plugged yet, so the current setup is:
NVIDIA 8800GT (binary driver 195.***)
--->1680x1050 LCD (VGA)
--->1680x1050 LCD (DVI)
ATI HD5450 (3 output, but I think the OSS driver only support 2, corrdct me if I am wrong) (OSS driver)
--->1280x1024 LCD (DVI)
---> 1366x768 TV (VGA)
[Code]...
View 2 Replies
View Related
Sep 6, 2010
How to setup two Ethernet cards ,one with public ip address and the other with local ip address.
View 4 Replies
View Related
Mar 11, 2010
The project is to setup a corporate server that will bond 5 pci lan cards into one! The scope is to connect 5 ADSL routers and compine the speeds of all of them.
So i would have 5 routers each 2mbit ADSL would result on a 10mbit connection.
The problem is not only that.
Because this is a corporate network the server MUST also act as a router. This is necessary because people are remotely connecting from e.g. their homes to the network.
if this can be done with a Linux server or it is not feasilbe at all?
View 5 Replies
View Related
May 18, 2011
I have just bought 2 monitors to be used as a x3 multi setup and 2 graphics cards the same make and model (ATI Sapphire Radeon HD5450). This all works in Windows 7 but I have just booted into Ubuntu and removed the old nVidia drivers and got the supported driver. The problem is only 2 monitors are detected as it would seem that it's only picking up 1 card.
View 1 Replies
View Related
Jan 30, 2010
I want to buy a laptop with gma 4500hd WHAT I WANT IS
1. 2D AND 3D full support eg compiz, full functional kde4+effects (not to be slow)
2. full hd support
3. oss driver
4. ability for dual head monitor setup
searching in google find out that as fa as it concern the dual head setup there is a limitation on virtual desktop for older gma cards
View 1 Replies
View Related
Dec 1, 2010
I have a dns server started with 2 NIC Cards in it. The bios sees both cards but they both dont show in ifconfig. is there a way to activate the second card?
View 1 Replies
View Related
Feb 7, 2011
Have a couple of very annoying problems. I recently did a re-install of Kubuntu Maverick on my HTPC/fileserver box.It has an onboard (Realtek?) audio card, recognized as... I think, ALC888... Yeah, not sure, KInfoCenter lists a bunch:ALSA Sequencer DeviceUSB 2881 Device ALSA Control Device (my DVB-T stick)ALSA Timer Device
HDA Intel ALSA hardware specific Device
ALC888 Analog ALSA Capture Device
ALC888 Analog ALSA Capture Device
[code]....
View 1 Replies
View Related
Mar 1, 2011
i earlier had windows xp installed on my personal computer..
when i plugged in my LAN cable..
it always showed "limited connectivity"..
then i had to repair it..
but now..
when i have installed Ubuntu 10.10..
it seemed to work fine for around 2-3 days..
but now..auto etho does not connect..
View 7 Replies
View Related
Jan 3, 2011
I'm running Ubuntu 10.10 on Macbook Pro 2,2 hardware. It stills picks up wireless internet (but cannot connect when the networks only have one or two bars...) but the ethernet won't accept a cord. It registers that a cord has been plugged into the computer, but will not connect to the internet via it.
I'm currently running on a live CD of Ubuntu 9.04, and the ethernet cord works fine, so it's not my hardware I'm worried about. (The change in registering cords came about after I re-installed Ubuntu after I wanted to switch to pure Ubuntu rather than running a dual-boot system.) It's something to do with the networking program I have on the system.
View 4 Replies
View Related
Mar 23, 2011
Just installed win7 next to ubuntu 10.10. on a newly purchased Dell inspiron N5030. Win 7 wire and wireless both work. In ubuntu , my wireless works. but cannot get the wire to work.I just ran ifconfig and found out i have nothing in the ethO at all.How do i put it in.
View 1 Replies
View Related
May 21, 2010
Cannot activate network device eth0!" device eth0 does not seem to be present, delaying initialization". i cannot find my network card while i set up network configuration
View 8 Replies
View Related
Nov 18, 2009
I'm stumped here as it seems like after an update etho:0 has assigned itself 2 x IP Addresses. I don't understand how this happened or how to fix it so some help would be great as I cannot access cPanel while it's like this or my sub directories.Here is a print of ifconfig
-bash-3.2# ifconfig
eth0 Link encap:Ethernet HWaddr AA:01:5F:9A:FE:26
inet addr:95.154.254.38 Bcast:95.154.254.38 Mask:255.255.255.255
[code]....
View 4 Replies
View Related
Mar 7, 2010
I got a problem about network proxy setting. With the graphics setting interface, I set auto proxy with the URL address but it is weird that the setting only work with eth1(wireless), doesn't work with etho(wired). however my wireless driver is always a problem for Linux. i also tried export http_proxy= XXXXX:8080 it still doesn't work at all.
View 2 Replies
View Related
Jul 6, 2010
I've brought a friend over to linux from windows. He has some how deleted his "Wired Etho" connection. He said his computer would not shut down(Mint Linux 9), so he unplugged it. You guessed it right after restarting no internet. After checking under "Network Connection" his wired connection is gone. My question is? How to reconfigure a "Wired Etho" connection? He has a dsl connection running a Linksys router(sorry I don't know the model number). I have only talked with him on the phone, so I have not personally checked the system out. I just finished working on it this past sunday and everything was fine.
View 3 Replies
View Related
Jun 7, 2010
i have problem related nici am using a dell inspiron 1545 laptop outputs are following---(1) [root@localhost ~]#lspci |grep -i ethernet 09:00.0 Ethernet Controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 13)
(2) [root@localhost ~]#cat /etc/modprobe.conf
alias scsi_hostadapter ahci
alias scsi_hostadapter1 usb-storage
[code]....
View 1 Replies
View Related
Mar 9, 2010
What's the easiest way of formatting SD cards to FAT32 in Fedora linux?
Also, I'm having trouble when I try to unmount the volume of a SD card, there's 0.8 GB being used that I expect to be cleared when I choose to 'empty trash', everytime I select 'unmount volume' the SD card window just shuts down instead of clearing that space.
View 2 Replies
View Related
Mar 16, 2011
I've got a Dell Xeon with two video cards - an nVidia Quadro2 MXR/EX/Go and an ATI Radeon 7000/VE. Under Fedora 10 Xinerama worked just fine, but I recently upgraded to F14 and Xinerama no longer works.The X server tries repeatedly to start but fails, with gdm-binary eventually giving up in disgust. If I comment out the ''Option "Xinerama" "On"' line it starts up (see attached xorg.conf), albeit with a few quirks. I have two X screens (:0.0 and :0.1 - one for each monitor), where :0.0 works just fine but :0.1 has no window manager - I can bring up windows on it but they have no window border ( no min/max/close buttons, can't be resized, etc). The mouse moves freely from one monitor to the other, but windows don't.The error messages I get when I try to use Xinerama are as follows. In /var/log/messages I get:
Mar 10 10:32:41 valdez kernel: [60328.892005] [drm] nouveau 0000:01:00.0: Allocating FIFO number 1
Mar 10 10:32:41 valdez kernel: [60328.892477] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised FIFO 1
Mar 10 10:32:41 valdez kernel: [60328.907615] [drm] nouveau 0000:01:00.0: nouveau_channel_free: freeing fifo 1
Mar 10 10:32:41 valdez gdm-binary[21435]: WARNING: GdmDisplay: display lasted 0.457045 seconds
[code]....
I've tinkered around with xrandr a bit but have had no luck - mostly the screen flickers briefly and things continue on as they were before.
View 1 Replies
View Related
Feb 4, 2010
Last update: 8/25/2011 Table of Contents
Introduction
Step 1: Identify the chipset of the wireless device
Step 2: Choose the right driver
Step 3: Install the driver
How to install and use b43 and b43legacy How to install and use the Broadcom 802.11 Linux STA driver (broadcom-wl) How to install and use b43-openfwwf
[Code]...
View 14 Replies
View Related
Nov 18, 2009
Greets all and congrats on the developers on bringing us another great version of Fedora. My box has an Nvidia GForce4 MMX 440 SE 64MB SDRam. I downloaded and updated from F11 to F12 last night. Before I went to bed It booted to a blank screen, GDM didn't want to start. I decided to investigate in the morning and went to bed. The first problem I found was that the F11 Legacy Nvidia Drivers were causing a problem, so I had to remove those. I also did an update with yum to get everything 100% updated. Then rebooted, more problems. GDM did NOT want to start for anything. More investigating found that the culprit was this nouveau kernel mod. Well, I had the xorg nouveau driver installed and I thought that this might be one in the same so I removed the xorg one with no avail, the nouveau kernal mod still loading. Seems that they are different and one is used for the xorg server and the other is used for the framebuffer console. I had to pass nouveau.modset=0 to the kernel at boot time to rid myself of the framebuffer. GDM starts now and I have resinstalled the xorg Nvidia nouveau driver though I have not tested it as of yet. Is there a better way at disabling the framebuffer boot up then by passing things to the kernel?
Edit: I take all that back. Upon further tinkering, reading, and investigation. The problem seems to be two fold: 1) The legacy nvidia drivers pissed and moaned about permission so I removed them. 2). This one I over looked and was causing me most of my grief. I didn't change the xorg.conf video driver from nv to nouveau. I did this and it works fine now. It seems that the "Linva-config-display" And I am sorry that I do not know exactly what this is at the moment. But this would automatically change the video driver from nvidia to nv if I manually changed it in the xorg.conf file after I removed the nvidia drivers. So I ASSUMED(my big mistake) that it would automatically see the nouveau driver and replace the nv with that. I was very wrong. After I added it manually, I rebooted and it runs fine now.
View 1 Replies
View Related
Jan 31, 2010
Due to the miss of proprietary drivers from AMD for Fedora 12, I have installed a second video card in my system (a Nvidia one) for BOINC calculation. This card is not connected to a monitor.
So in the system I have this two cards:
ATI Shappire Radeon HD2600XT (256MB)
Asus Nvidia Geoforce 6600 (356MB)
The ATI is in the first PCI express device, the Nvidia to the second PCI express:
Code:
So I have used this Xorg configuration file (if I let Xorg to configure without the configuration file, it sets NVidia to default card and X files to start):
Code:
The Nvidia driver were installed as described in some forum:
1) disabling nouveau in grub configuration
Code:
2) Take SElinux to alow the driver:
Quote:
With this, the driver is correctly loaded in memory:
Code:
But the Xorg says that not Nvidia Driver where found (see the attack file).
These are the NVIDIA driver installed:
Code:
What can I do to make NVIDIA driver to work?
View 2 Replies
View Related
Oct 17, 2010
I am a bit overwhelmed with all the information out here, and can't get this to work properly after trying to for two days. I have a PCI ATI card(Sapphire Radeon 9250):
00:08.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 PRO] (rev 01)
00:08.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200 PRO] (Secondary) (rev 01)
of which I am only wanting to use the Primary, and my onboard video:
01:00.0 VGA compatible controller: VIA Technologies, Inc. KM400/KN400/P4M800 [S3 UniChrome] (rev 01)
right now my xorg.conf is empty and I only get a display off my ATI card. How can I get my onboard to display as well like it does in windows?
I've tried many ways that I found and nothing seems to work.
View 2 Replies
View Related
Nov 15, 2010
I just installed Fedora 13 on my desktop computer and ran into the same problems I did when I tried to install which was i could connect to a network but couldn't access the internet. I decided to install Fedora 14 since I already installed it on my laptop. I'm still running into the same issue, I can connect to my network but cannot connect to the internet using my PCI NIC or onboard NIC. Networking is enabled and I'm getting a IP address from my router. I ran "lspci" and it shows me both network cards which, please correct me if I'm wrong, makes me think that the drivers are installed.
I'm also curious if the VNC client/server could be used through a WAN. I would like to remote into my computer at home when I'm not there and see the gui. I had SSH installed at one point but it was just text. If there is better program please let me know. why I would have Services on my laptop but not on my desktop? Both computers are running the same version. Both cards are enabled and set to connect automatically. I can get a IP with both NICs. I only have one plugged in at a time.
View 14 Replies
View Related
Nov 17, 2010
I have just upgraded to Fedora 14, with some hope that a F13 kernel crash issue would be resolved. Alas, not, and I have lost audio in one of my sound cards. I am using 2 sound cards in my computer. The first one (VT 1708 on the M2V MX SE motherboard) is used for FLDIGI (ham radio program). The other one (Creative Labs SB Live!) is tied to a speaker/microphone. At some point in mid 2010, I started getting kernel crash reports (not sure which kernel version this started), and the VIA VT 1708 audio controller stopped working. The SB Live! card works fine.
From mesg, I get:
[9.181148] WARNING: at drivers/pci/pci.c:105 pci_ioremap_bar+0x2c/0x5b()
[9.181186] [<c05c36ad>] ? pci_ioremap_bar+0x2c/0x5b
[9.181194] [<c05c36ad>] pci_ioremap_bar+0x2c/0x5b
[9.181299] ALSA sound/pci/hda/hda_intel.c:2510: ioremap error
I've just pulled out the SB LIVE! card to see if it is causing the VT 1708 controller to fail...there appears to be no interaction.
From lspci -v, I get:
20:01.0 Audio device: VIA Technologies, Inc. VT1708/A [Azalia HDAC] (VIA High Definition Audio Controller) (rev 10)
Subsystem: ASUSTeK Computer Inc. Device 8290
Flags: fast devsel, IRQ 17
Memory at <ignored> (64-bit, non-prefetchable)
Capabilities: <access denied>
Kernel modules: snd-hda-intel
So it seems to know it's there. How to get my sound back (and get rid of this kernel crash every time I start my computer)?
View 1 Replies
View Related
Mar 17, 2011
I have onboard video card (GeForce 6150SE nForce 430) and I install one PCI-E video card (GeForce 7300 GT). In BIOS I set primary video cart to onboard. Is it possible to work simultaneously? lspci -v command showing both, but nvida-setting, nvidia-xconfig and system-config-display only show one, never both.
lspci -v
00:0d.0 VGA compatible controller: nVidia Corporation C61 [GeForce 6150SE nForce 430] (rev a2) (prog-if 00 [VGA controller])
Subsystem: ASRock Incorporation Device 03d0
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
[code]....
View 7 Replies
View Related
Apr 19, 2011
My laptop has these Broadcom chipsets (from lspci):
Code:
00:09.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 02)
02:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 01)
The 4321 is working fine with wl, but I can't figure out how to get the 4306 working. As I understand, I can't use wl for that one. I once had it working (in FC10 or so) with b43legacy, which is now blacklisted for wl. Unblacklisting it alone doesn't make the other card work. Is there some other configuration I need to do?
View 4 Replies
View Related
Oct 31, 2009
I have Installed Fedora 10 and I have assigned manual IP address to eth0 and trying to activate the eth0 but all buttons are disabled.
View 2 Replies
View Related
Jun 23, 2010
I have installed Ubuntu 10.04 LTS on my Compaq 767TU notebook. Everything is working fine except "Realtek RTL8139 PCI adapter". Although it is showing up in device list and installed but the LAN link indicator lights are off. No communication is possible with dhcp.
View 2 Replies
View Related
Aug 2, 2009
I have an M-Audio Delta 44 sound card, and a USB MIDIinterface device, both are recognized, and work. My problem is as each are seen by alsa as sound cards, sometimes the alsa card numbers switch between boots. Is there a way to set these devices to always have the same card number for alsa
View 1 Replies
View Related
