Can't get my WiFi to work on my HP. My WiFi chip is bcm4303 (rev. 2) this is a new thread from http://ubuntuforums.org/showthread.php?t=1400427&page=4 ) So, I reinstalled Ubuntu (fresh install) Activated the Broadcom b43leagacy Wireless driver. When rebooting, the WiFi LED on the On/Off switch blinks.
[Code]...
I'm relatively new to Ubuntu and Linux OS in general, hope this hasn't already been solved but after trying for 24hrs+ I think it may be time for me to start my own thread (sorry if there is already one). I have been desperately trying to get my Broadcom BCM4312 wireless card to work and after searching about 100 sites and threads I still can't get it going Here are some of the problems Ive been having(I am running Ubuntu 8.04 by the way):
1. Tried installing "Broadcom STA Wireless Driver" under System->Administration->hardware drivers but after install it didn't show any signs of working.
2. I tried getting the Linux driver off the website [URL]... and followed the instructions in the readme to the letter, yet when i am asked to type in one of the final commands: # sudo insmod wl.ko
I get the output: # error inserting 'wl.ko': -1 File exists I have also looked at this website where a guy posts the same problem but no one posted anything back: [URL]...
I am having problems making wireless work on my pc. I have searched the forums and tried several things (b43-fwcutter, among others) and I cannot get anything to work. My computer is an HP ze4900, broadcom wireless Quote:
*-network:1 UNCLAIMED
description: Network controller
product: BCM4306 802.11b/g Wireless LAN Controller
[code]....
get WIFI working on my Dell D600 with Ubuntu 11.04 freshly installed. I some limited sucched following the this post t=1621331 this got the card working but it was very very slow over 70% packet loss to the WIFIrouter. 1. Machine details Dell Latitude D6002 Wireless Broadband and Chip setlspci -nn | grep Broadcom - 02:03.0 Network controller [0280]: Broadcom Corporation BCM4309 802.11a/b/g [14e4:4324] (rev 02)3. Check interfaces
eth0 Link encap:Ethernet HWaddr 00:0b:db:e0:1c:5b
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[code]...
i installed Ubuntu 11.4 on a hp pavilion g6 and all seemed good until i realized the wireless on/off toggle switch( that is integrated into f12) wouldn't toggle so it is stuck on off. so now i have been fores to the basement to use an Ethernet cable.
View 1 Replies View RelatedI recently upgraded from 9.04 to 10.04 and can no longer connect to the internet, even after enabling wireless networking in the Network Manager. This happened to me on a different laptop recently, but someone here linked me to the proper drivers and solved my problem.
lspci
Code:
00:00.0 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP67 ISA Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP67 SMBus (rev a2)
00:01.2 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
[Code]....
I downloaded ubuntu 11.04 on my HP Pavilion dv6000 laptop and the wifi on it doesn't work. I'm running it in parallel with windows xp and the wifi works find on windows (as it has always done) but once I boot the laptop in ubuntu, it doesn't recognise anything, no driver, nothing.
get the wifi working in ubuntu on my laptop. Ubuntu is pretty much useless to me if I can't get the wifi to work on it.
i'm having a lot of trouble getting my wifi to work on my dell inspiron e1405 laptop. I looked through the forums and tried a few solutions to no avail
View 9 Replies View RelatedHow do I setup Wifi on my labtop. When I run linux live cd on my desktop which is connected to my router, linux's pickup ethernet connection and connects fine to the internet. but on my labtop which is wireless to my router linux will not see my wireless connection. How do I configure linux to connect through wifi.
View 2 Replies View RelatedI've been reading up on how to get the Broadcom BCM4312 802.11b/g on my Dell Inspiron 1525 to work with OpenSUSE and I've tried everything, I've even re-installed the OS 3 times as I seemed to keep screwing something up. I've tried doing what it says in this thread
Install Broadcom Drivers from Packman
I thought I'd installed the write drivers with this code:
Code:
zypper in broadcom-wl broadcom-wl-kmp-default
This laptop arrived in the post yesterday and everything on f15 works out of the box except wireless.Digging out an old ethernet cable I was finally able to get wireless working by doing the following: First install ndiswrapper. We'll be using rpmfusion for this so you'll need to
[Code]...
After a reboot it all loaded and worked fine, just remember to make sure the little light on the f12 button is blue, not red. This guide should work for other laptops and other distros as well (though obviously you'll likely need a different driver file to start off with).
Wifi works on 11.3 with installed the broadcom-wi & broadcom-wl-kmp-desktop,but this trick doesn't work on this new 11.4.
View 9 Replies View RelatedI recently installed Suse 11.4 on my Dell Latitude 2110 netbook using the KDE live distribution, and, after that, the Broadcom wireless ceased to work. To enable the wireless connection, I have to press Fn + F6. If I do it now, the wireless led indicator turns on for a couple of seconds, then turns off again. Moreover, the option to enable the wireless connection in the network manager is greyed out
lspci output:
Code:
0c:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01)
iwconfig output:
Code:
wlan0 IEEE 802.11abgn ESSID:off/any
Mode: Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit: 7 RTS thr: off Fragment thr:off
Encryption key: off
Power Management: off
dmesg output:
Code:
[8.330963] brcm80211: module is from the staging directory, the quality is unknown, you have been warned.
[8.362403] brcm80211 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[8.362422] brcm80211 0000:0c:00.0: setting latency timer to 64
output of rpm -qa | grep broadcom:
Code:
broadcom-wl-kmp-desktop-5.100.82.38_k2.6.37.1_1.2-7.pm.8.1.x86_64
broadcom-wl-5.100.82.38-7.pm.8.1.x86_64
Im using natty in lenovo b460. After installation was not able to connect to wifi. Ethernet is working alright. So searched for additional drivers and installed the Broadcom 43xx drivers. After restart the network applet says the wireless is disabled by hardware switch, even after it is switched on/off several times.
Lenovo B460
kernel:2.6.38-8-generic 32-bit
Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
ubuntu 11.04
[Code]...
I have an emachines D620 laptop running Ubuntu 10.10 with a Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01). I havent done anything with it and cant seem to get it to work. I know this because when I had visto on it the card worked, but know it says that its firmware is not enabled and ive tried installing the drivers using the Additional Drivers under Administration. I would like it to be working so I can use my laptop's internet.
View 5 Replies View Relatedi am using broadcom wireless (4312) on my laptop with FC15 and configured it using [URL]. initially it ran great without any problem (for a week). but from yesterday, every 15 minutes or so, my wifi started getting disconnected, showing the wireless login screen . I can reconnect only by rebooting or restarting network manager service.
View 6 Replies View Relatedi have a broadcom BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) wireless adapter on a dell 1501 run by ubuntu 10.10.this particular model and revision is suppose to be absolutely supported by linux and indeed it did work perfectly before the user ran a upgrade from ubuntu 10.10 to 11.04.subsequently i have reinstalled 10.10. as i recall when i installed ubuntu 10.10 the first time i simply ran the System>Admin>Additional Driver installation tool to make the wireless work. i cannot recall if i ran the b43 or the sta driver but i have tried both this time and had no luck.
i am aware that the broadcom adapters are notoriously troublesome and i have tried the two workarounds here URL... as well as their third alternate workaround with no success.
I have a HP Pavilion dv6-2155dx Entertainment Notebook with Broadcom Wireless Lan Driver.
I didn't want to bother anyone with this, but I just could't find a solution. I was happy using Ubuntu 10.04 LTS Desktop Edition, because the wifi was working fine, but I messed everything up dealing with networking in terminal.
So formated and now I have Ubuntu 10.10 Netbook Edition, but that didn't solved my problem at all, because my wifi driver still unfunctional.
Before anything, I tried commands like "dbus restart" and "network restart".
So after reading that I can install by getting ndisgtk and the .inf file, I downloaded the right driver from HP Support's page of my notebook. Extracted the package with Wine (got some error because I wasn't running Win7, of course, but that doesn't matter.).
I did this: [url]
And this is my final result:[url]
Technical informations:
Quote:
I just installed 9.10 and I can't detect any wireless networks. Is the card compatible with 9.10? Do I need to install any drivers? If the card isn't compatible with 9.10 is it compatible with later versions of Ubuntu? Marking this as somewhat urgent as I need to get internet access for some coursework soon, and also because my parents will kill me if they find out I've done anything unusual with the laptop because it's new and they think anything non -MS is a virus.
View 9 Replies View RelatedI have had a search around, any cannot find any thing I can make sense of as to how I go about getting the above card to work with Fedora 11. Just done a fresh install (need Linux for some development) but have no wifi. My chipset is this Broadcom BCM4310. There seems to be a whole load of options, and I don't know which works and which don't:
kmod-wl
broadcom-wl
ndiswrapper
I can sit with an Ethernet cable to install/update as necessary, but really could do with wireless.
I am succesfully installed a Dell wireless card with Broadcom 4328 shipset using ndiswrapper and rpm sources on Fedora 12 2.6.32.14-127.fc12.i686.PAE. Now I am using original Win drivers but the wifi conection is very slow and unstable.
The wifi card runs perfectly on win 7.
This is the lspci -vvnn outpput
03:00.0 Network controller [0280]: Broadcom Corporation BCM4328 802.11a/b/g/n [14e4:4328] (rev 03)
Subsystem: Dell Wireless 1500 Draft 802.11n WLAN Mini-card [1028:000a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
[Code].....
I still try update my broadcom drivers, because when I try use airodump-ng i receive error.
This error:
Interface Chipset Driver
eth1 Unknown wl (monitor mode enabled)[code]....
I dont know why receive this error WARNING: modpost: missing MODULE_LICENSE() in /home/mobile/Desktop/wdriver/wl.o
see include/linux/module.h for more information
I installed Ubuntu 10.10 amd64 online today. I was using 10.04 32-bit before, and the network drivers were easy to find and install. Ubuntu did the job for me and they worked flawlessly. It was a relief I didn't need to search around.
Even though 10.10 (64bit) found the drivers for me, both ethernet and wireless, they do not seem to be working alright. I installed both, made a restart. I found that the WiFi light on my laptop stays on, even if the wireless network is turned off using either the key combination (Fn+F2), or manually turning it off.
Issues with the ethernet? I am right now using ethernet but it does not care to detect the connection. Empathy won't connect automatically as a result- says no network connection. But here I am, posting this. Evidently, there is a connection, right?
Issues with the wireless? The WiFi light stays on all the time, and it isn't able to get hang of the connection I have at home. It just won't show any wireless connections available. When I tried to connect by giving it the SSID and the encryption type and password, it didn't work. Just kept asking for the password again and again (I have checked with the router- the password is correct).
ok basically i have a new dell inspiron n5010 with a broadcom 4313 wifi card. it doesnt work with ubuntu studio 10.10. I have the drivers all installed and it works on ethernet with the broadcom STA proprietry driver. if i disable this driver the eth doesnt work. but the driver shows its working (screenshot-1).
There is no pop up or anything in the task bar for detected wifi. i open the network settings and it shows up with a wifi option but i have to go into properties and manually type in what i have "the_den_meribel". which didn't work. (screenshot-2).
i have tried the other driver broadcom-sta-common and that doesnt make it work either. screenshot-3. i did try to install the "lp-pphhy" or whatever it is (seacrh for firmware-b43 in synaptic).
i have a list of results from what i have typed into the terminal: dell inspiron n5010
Code:
sam@drytopubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18)
[Code]....
I just put 10.10 on my D830 and I love it except for a delay when I'm using the internet. When I click on a link while surfing the web it takes about 13 seconds before it responds. After that it works just fine.
My Windows 7 PC and my Macbook Pro don't do that so I'm guessing it has something to do with Ubuntu.
I just installed the 64-bit Kubuntu 11.04 and i've been having some issues getting the wifi to work. At first I went to additional drivers and activated the STA driver and restarted. After restarting when I went into the network manager and any option for wireless was disabled.
[Code]....
I'm new to Ubuntu as of yesterday, and know very little of Linux in general. I tried RedHat for a while about 10 years ago and remember almost nothing from the experience. I'm up and running with everything working great with one exception -- my wireless. The error: Contents of jockey.log as suggested: -Sorry, it's long. Not sure what (if anything) is relevant.
[Code]....
I have a compaq Presario C500 windows vista and I installed Ubuntu natty Ubuntu 11.04 by using Wubi.What I really need right now is an executable b43-fwcutter, and I don't know how to get it. When I boot up in Ubuntu, I've got no wireless. There's an access point I can connect to (if not using Ubuntu), but Ubuntu isn't activating the interface card. I've got no wired interface nor hope of one.
I slogged through countless webpages and came to the instruction [URL].. that I should install b43-fwcutter and use it on wl_apsta_mimo.o. It tells me to install using command `sudo apt-get install b43-fwcutter' (sorry if that's not the proper etiquette for posting a command) but I can't install with that command because apt-get wants to use the Internet. (err msg: "E: Unable to locate package b43-cutter") So, I have wl_apsta_mimo.o and the other files that come with it in directory broadcom-wl-4.150.10.5. But I don't have b43-fwcutter and I can't figure out how to get it.
[URL].....ernet%20access tells me "b43-fwcutter is located on the Ubuntu install media under ../pool/main/b/b43-fwcutter/ " but I can't find that directory. Where is it?
I did a full install of 9.10 on my Dell Inspirion 1200 laptop & use a Dell 1350 card, after several posts and replies I went to [URL]and followed the instructions for Ubuntu/Debian. This is the result I get....
mike@mike-laptop:~$ sudo apt-get install b43-fwcutter
[sudo] password for mike:
Reading package lists... Done
Building dependency tree
[code]....
I followed this procedure before installation (live CD) and it successfully found and installed the firmware. Apparently it was saved in live CD. What do I need to do?
I have an LM Technologies 54Mbps wifi usb adapter.This is because my wireless section on my motherboard does not work.The drivers on the installation disk do not automatically install for linux. Looking at the manual I have to build the device driver. On the page is computer programing formulie that looks like a foreign language. I do not know computer programing. At the bottom of the page it says:-
Install individual driver
If you only need driver of ZD1211 or ZD1211B you can issue:
make clean
make ZD1211REV_B=0(0 for ZD1211,1 for ZD1211b)
make ZD1211REV_B=0 install(o for ZD1211,1 for ZD1211B
to install the driver.
Then it says:- Build the debugging tool. There are two debugging tools in this package,"apdbg" and "menudbg". Run"make debug" to complete them both. If you do not have ncurse library, you may get some error messages while compiling meudbg. you can ignore it and get apdbg only. It goes on and on about network interface, configure wireless settings.