How do I setup Wifi on my labtop. When I run linux live cd on my desktop which is connected to my router, linux's pickup ethernet connection and connects fine to the internet. but on my labtop which is wireless to my router linux will not see my wireless connection. How do I configure linux to connect through wifi.
View 2 Repliesi installed Ubuntu 11.4 on a hp pavilion g6 and all seemed good until i realized the wireless on/off toggle switch( that is integrated into f12) wouldn't toggle so it is stuck on off. so now i have been fores to the basement to use an Ethernet cable.
View 1 Replies View RelatedThis laptop arrived in the post yesterday and everything on f15 works out of the box except wireless.Digging out an old ethernet cable I was finally able to get wireless working by doing the following: First install ndiswrapper. We'll be using rpmfusion for this so you'll need to
[Code]...
After a reboot it all loaded and worked fine, just remember to make sure the little light on the f12 button is blue, not red. This guide should work for other laptops and other distros as well (though obviously you'll likely need a different driver file to start off with).
I recently upgraded from 9.04 to 10.04 and can no longer connect to the internet, even after enabling wireless networking in the Network Manager. This happened to me on a different laptop recently, but someone here linked me to the proper drivers and solved my problem.
lspci
Code:
00:00.0 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP67 ISA Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP67 SMBus (rev a2)
00:01.2 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
[Code]....
I downloaded ubuntu 11.04 on my HP Pavilion dv6000 laptop and the wifi on it doesn't work. I'm running it in parallel with windows xp and the wifi works find on windows (as it has always done) but once I boot the laptop in ubuntu, it doesn't recognise anything, no driver, nothing.
get the wifi working in ubuntu on my laptop. Ubuntu is pretty much useless to me if I can't get the wifi to work on it.
Can't get my WiFi to work on my HP. My WiFi chip is bcm4303 (rev. 2) this is a new thread from http://ubuntuforums.org/showthread.php?t=1400427&page=4 ) So, I reinstalled Ubuntu (fresh install) Activated the Broadcom b43leagacy Wireless driver. When rebooting, the WiFi LED on the On/Off switch blinks.
[Code]...
I'm not 100% sure as to where exactly to post this, but I've been wanting to set up a second computer for a while, and I finally put together a computer using the original motherboard and CPU from an HP Pavilion 7905, 1.6 GHz. I put in 512 MB of RAM, and I burned a Slackware DVD using my main computer. But when I boot up the DVD, I had an issue booting to the "normal" kernel, the hugesmp.s one. So, I tried the huge.s kernel, and it's still not working for me. I got the following output out of it when it crashed // froze:
View 4 Replies View RelatedI have an LM Technologies 54Mbps wifi usb adapter.This is because my wireless section on my motherboard does not work.The drivers on the installation disk do not automatically install for linux. Looking at the manual I have to build the device driver. On the page is computer programing formulie that looks like a foreign language. I do not know computer programing. At the bottom of the page it says:-
Install individual driver
If you only need driver of ZD1211 or ZD1211B you can issue:
make clean
make ZD1211REV_B=0(0 for ZD1211,1 for ZD1211b)
make ZD1211REV_B=0 install(o for ZD1211,1 for ZD1211B
to install the driver.
Then it says:- Build the debugging tool. There are two debugging tools in this package,"apdbg" and "menudbg". Run"make debug" to complete them both. If you do not have ncurse library, you may get some error messages while compiling meudbg. you can ignore it and get apdbg only. It goes on and on about network interface, configure wireless settings.
setting up the lan and wifi settings
View 3 Replies View RelatedI just installed ubuntu server 10.04. I want to connect to my wireless router(192.168.123.254). My router normally has wpa but I turned off encryption until I can get the server working. my router has MAC flitering which it has my servers MAC address and the dhcp server on my router is configured to assigned an ip address of 192.168.123.123 to my server.
On the server I do see wlan0 when I do sudo ifconfig -a. HOw do I setup the rest? I 'm very new with command line and linux so please bear with me.
I just got a new desktop (the client) and hooked my "old" computer (the server) up to it with a crossover cable & NFS while I set up the new system.Unfortunately, while nfsd is running firefox cannot access the internet through ath0 -- the wifi card (NFS/rpc is on the ethernet card). Do I have to set up a proxy server (eg. squid) or is there a simpler solution?I don't need direct access to the net on the client. I just want to be able to use the wifi's IP in the server while it has a NFS client on eth0, so that firefox can work online.
View 2 Replies View RelatedYesterday, I did a clean install of Lucid on a T42 thinkpad, with wireless card as identified by lshw below. I did the installation from within a live CD session, with wifi enabled.
Code:
description: Wireless interface
product: PRO/Wireless LAN 2100 3B Mini PCI Adapter
vendor: Intel Corporation
On reboot into the fresh system and update I had the issues that others have seen with network manager not connecting, repeatedly asking for password and so on. Oddly enough, using a Netgear usb wifi dongle worked perfectly, so I thought there might be a driver issue. Updates did not help. The network manager icon would not appear in the notification area at all when attempting to connect to wifi in a cafe locally. Today, I did a fresh re-install from the same CD with the home wifi switched off and no internet connection on the laptop. No issues. Wifi is working perfectly at present. I had to make the home connection available to all users to stop the keyring password request (I use autologin). I'll be trying to connect at local cafes tomorrow (one has no security, one uses an ascii wep password, and a third has a WPA encryption)
Is it possible that the settings from the live session are carried over in some way and interfering with network manager in some way? (This all started because my minimal install (see signature) reached a state where it would not show the network manager icon when attempting to connect to wifis in cafes and colleges, which I need to do. I decided to reinstall to return to a known state. I may try a minimal installation and manual wifi connection from the command line next...)
I've got an Ubuntu box set up as a router and wifi hotspot. I can access the internet and any website using this box. I can connect a laptop to my wifi access point, and connect to both the router box and the internet. I'm writing this message from it. If I access either hsbc Hong Kong internet banking or speedtest.net from my laptop I can't connect. Every other site I've tried is fine. What could be causing this? I don't know where to start. I've set up the firewall rules and routing tables, so I vaguely know what I'm doing... but clearly not enough to debug this issue.
View 3 Replies View RelatedI have an old dell desktop with a belkin wifi dongle that connects to the internet right away when i boot in live cd mode but when i try while its installed/installing i get the connecting animation on the wifi, thing, on the top bar.it connects then loses connection and cannot reconnect 5-10 minutes later. this is driving me crazy, i have homework and i just need this thing on the internet already so i dont have to stress my macbook with a minecraft server
View 2 Replies View RelatedI have installed and un-installed 3 different versions of Ubuntu. My fourth is a re-install of v9.10. During all these installs I have had difficulty getting my wifi to work. During my last install I left the ISO in the drive by mistake so when the system rebooted it loaded from the disc in demo.... This was interesting because in the demo the program manager showed 2 drives for wireless, 1 Broadcom STA and 2 Broadcom b43xx. I tried loading the STA and it worked! (sorry it could have been the b43xx, for the time being it's insignificant) Upon my excitement I restarted the computer and removed the disk went to my Ubuntu set up and ...what the Broadcom choices weren't there Why?
Now I am running Win 7 Home 32bit on my main drive and have Ubuntu loaded on its own drive. I have a Netgear WN311b wireless N card installed. Again my confusion is why it worked in demo (off the cd) but doesn't from full install. I read on the web to try inserting my supplied disc from Netgear and then search program manager. It now showed the two for-mentioned Broadcom programs, but this time wouldn't install them. On the b43 I got an error message and on the STA it searched extracting and loading this continued for a 1/2 hour with no progression. I couldn't close the PM or the extracting and loading box, so I had to restart the computer.
I've had 8.04 for almost a year & a half now, but the one thing that seems to confuse me after getting the rest of ubuntu is how to get wifi working. Before you say "read XXX FAQ, wiki, page", etc, I've read so many and despite understanding every normal thing about ubuntu, and all the customization I have, I haven't seen a single, up-to-date guide for making sense of wifi.
Here's what I know:
My wireless card is Network controller: Intel Corporation PRO/Wireless 2915ABG Network Connection (rev 05), supported in linux only by using a windows driver, ipw2200, which I do have running and installed somehow.
Code:
shogun@Valhalla:~$ sudo lsmod | grep ipw2200
[sudo] password for shogun:
ipw2200 146248 0
ieee80211 35528 1 ipw2200
I also realized I needed ndiswrapper, so I installed that. Beyond this, I'll just admit it- I'm very confused. I have always had a working connection over ethernet cable plugged in, but I really need wireless lately, and found an old Netgear WGR614v7 G band wireless rounter in my basement, hooked it up, and have a wired connection from it right now.
So how do I set-up/get my wireless working with all this thus far? How do I set up the router's network through Ubuntu as well, so I can create a named network to connect to? I'm reading every guide I can, and am just coming up more confused.
I got two issues with my wifi usb adapter:
1) it cannot see any networks around
2) i cannot setup it in master mode to use my PC as a router
As far as i can see, the device is recognized and the correct driver (rt73usb) is loaded. I was able to connect to a laptop somehow (the laptop could see other networks and the adapter's PC-to-PC network). I'd like to make it work as a router, i.e. share my internet connection (eth0) via wlan0. Here is what i have:
Code:
Ubuntu 10.04
Linux 2.6.32-22-generic #36-Ubuntu SMP Thu Jun 3 19:31:57 UTC 2010 x86_64 GNU/Linux
TP-Link TL-WN321G wifi usb adapter as seen as
Bus 001 Device 006: ID 148f:2573 Ralink Technology, Corp. RT2501USB Wireless Adapter
$ iwconfig wlan0
wlan0 IEEE 802.11bg ESSID:off/any
[Code]....
ok so the router works in windows and i know the config details of it.i can see other wifi access points in the area but not my one. i have tried joining it as a "hidden network" to no avail.is there any reason why fedora would not detect my own wifi when it detects substantially weaker signals instead??
View 2 Replies View Relatedi have windows 7 installed on my samsung labtop . i want to install opensuse so it be dual OS on same laptop when i come to the disk part in installation is suggests formatting the whole hard disk including the hidden recovery partition as it don't see win7 at all while i have 22gb unformated space for installing opensuse.
View 2 Replies View RelatedI am dual booting with windows xp on a dell computer I recently acquired. I am running Ubuntu 10.10. The computer didn't have a wireless connection so I installed a wireless pci adapter from a company called ZONET. I installed it perfectly on windows xp, however, I cannot install the driver and the "Ralink Wireless LAN" on Ubuntu. I inserted the cd, and opened the setup.exe file with Wine Windows Program Loader (I have installed Wine 1.3 by following the instructions on http://www.winehq.org/download/deb and clicking on the link that says "click here".
I am currently temporarily connected to the internet by borrowing my main computers ethernet cable). I followed the instructions on the InstallShield Wizard only to have two windows pop up saying there is an error (see attached image).
New to these boards and thought I'd try my luck w/ Ubuntu for a strictly school/work labtop. I created an install disc and booted from it. But nothing appears it's just a black screen, I have to restart everything to get anything done.
Labtop is a Acer Aspire 5736z-4427 with a Intel T4500 processor. Now I know it is not 'officially' listed as a certified notebook, is that the reason why it's not running the disc? Or should I try re-burning a disc and try again? I'm trying to install Ubuntu's latest version btw.
I installed
Ubuntu-11.04-beta1-desktop-i386
Ubuntu-10.10-netbook-i386
From windows 7 i select to install on same windows7 partition after installation i select ubuntu and it start up to complete the installation put i get a message: "No root file system please correct this from the partitiong"
I reinstall again on a vartual machine with windows 7 it worked ok;
I installed it with other pc with windows xp it worked ok
I installed on another labtop the same problem occured.
I'm relatively new to Ubuntu and Linux OS in general, hope this hasn't already been solved but after trying for 24hrs+ I think it may be time for me to start my own thread (sorry if there is already one). I have been desperately trying to get my Broadcom BCM4312 wireless card to work and after searching about 100 sites and threads I still can't get it going Here are some of the problems Ive been having(I am running Ubuntu 8.04 by the way):
1. Tried installing "Broadcom STA Wireless Driver" under System->Administration->hardware drivers but after install it didn't show any signs of working.
2. I tried getting the Linux driver off the website [URL]... and followed the instructions in the readme to the letter, yet when i am asked to type in one of the final commands: # sudo insmod wl.ko
I get the output: # error inserting 'wl.ko': -1 File exists I have also looked at this website where a guy posts the same problem but no one posted anything back: [URL]...
I'm a newcomer in ubuntu 10.4, and with my HP Pavilion dv4000 can't see the wireless device pollo rodighieroI asked the terminal, and answers are:
lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 04)
[code]....
i'm realy new in all linux concern, and i dont really have to many problems with ubuntu. But the other day i strted using CDLinux, which is really amazing despite the fact i can't get it connect to the wireless, i know the pass of the signal, i'm not trying to hack it, is a WPA, and i don't really know what i'm doing wrong.
View 6 Replies View RelatedI just installed that latest version of Ubuntu on to my HP *a6750f Pavilion PC. I am using my wireless card on it. When i use the internet sometimes it will work for awhile but then it won't. So my internet keeps cutting in and out. I am not being diconnected from my router though. Internet is working prefectly fine on my other computers running windows seven and ubuntu.Here is my information
------------lspci code returned
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge
00:01.0 PCI bridge: Hewlett-Packard Company Device 9602
[code]....
I just installed ubuntu 9.10 on my HP Pavilion (dv7-3017). Problem is that I have no wireless connection.When pressing wireless button the light stays orange instead of turning blue. My paviion is using Atheros network card. I'm linux newbie so it would great if you could out solving this problem.
View 4 Replies View RelatedI just installed Ubunto 9.10 on my HP Pavilion ZE9400 laptop (more specifically a ze4930us) that was formerly running Windoze XP. Right now, I'm using my Win 7 desktop machine. The problem with the laptop is that Linux can't connect to my wireless network. It seems that it can't see the wireless card. When I tap the button on the laptop case, a little blue light normally switches on and off to indicate whether the wireless card is enabled or not, but that light doesn't come on. I suppose I need a HP/Ubuntu driver. Any advice, links, etc?
BTW, I also went to the HP site to download a driver, but Linux isn't one of the OSs that they support and have no drivers.
Installed 11.04 (64bit) on my HP Pavilion G6, in place of windows. ethernet works, however i cannot connect wirelessly. i have done much Google searching but to no avail.
[URL]
i have got an HP Pavilion g6-1142sl and i installed on it ubuntu 11.04. i have some problems with the wireless. i have already read a post on this forum wich explained how to get drivers here the link: [URL] i got them and the wireless started working (a month ago) now, a couple of days ago it stopped working when i did a restart due to an automatic update. and that is what i can see with terminal:
[Code]...
what can i do in order to have a working wireless? i am sorry if my english is not properly good but i am italian.