I've been reading up on how to get the Broadcom BCM4312 802.11b/g on my Dell Inspiron 1525 to work with OpenSUSE and I've tried everything, I've even re-installed the OS 3 times as I seemed to keep screwing something up. I've tried doing what it says in this thread
Install Broadcom Drivers from Packman
I thought I'd installed the write drivers with this code:
Code:
zypper in broadcom-wl broadcom-wl-kmp-default
Wifi works on 11.3 with installed the broadcom-wi & broadcom-wl-kmp-desktop,but this trick doesn't work on this new 11.4.
View 9 Replies View RelatedI recently installed Suse 11.4 on my Dell Latitude 2110 netbook using the KDE live distribution, and, after that, the Broadcom wireless ceased to work. To enable the wireless connection, I have to press Fn + F6. If I do it now, the wireless led indicator turns on for a couple of seconds, then turns off again. Moreover, the option to enable the wireless connection in the network manager is greyed out
lspci output:
Code:
0c:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01)
iwconfig output:
Code:
wlan0 IEEE 802.11abgn ESSID:off/any
Mode: Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit: 7 RTS thr: off Fragment thr:off
Encryption key: off
Power Management: off
dmesg output:
Code:
[8.330963] brcm80211: module is from the staging directory, the quality is unknown, you have been warned.
[8.362403] brcm80211 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[8.362422] brcm80211 0000:0c:00.0: setting latency timer to 64
output of rpm -qa | grep broadcom:
Code:
broadcom-wl-kmp-desktop-5.100.82.38_k2.6.37.1_1.2-7.pm.8.1.x86_64
broadcom-wl-5.100.82.38-7.pm.8.1.x86_64
I've installed new drivers and when I go to connect the MAC address shows up on the router but only for a few seconds and then disappears and I can't access wifi. I've even attempted opening up the router and still can't connect.
View 2 Replies View RelatedI am having a problem while connecting to a D-Link Access Point with Multiple ESSID. It keeps saying activating but in the end nothing. I am using KnetworkManager & there is no Encryption on the Access Point.I am able to get connected with another machine using windows.Here is my hardware info:
0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01)
Subsystem: Dell Wireless 1397 WLAN Mini-Card [1028:000c]
Kernel driver in use: b43-pci-bridge
& the logs:
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.188245] wlan0: authenticate with f0:7d:68:17:e5:a4 (try 1)
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191262] wlan0: authenticated
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.191501] wlan0: associate with f0:7d:68:17:e5:a4 (try 1)
Feb 3 15:44:00 Shiraz-Suse kernel: [ 316.194008] wlan0: RX AssocResp from f0:7d:68:17:e5:a4 (capab=0x421 status=0 aid=1)
[Code]...
I recently installed suse 11.4 x64 onto my hp tx2000 tablet. everything has been working great including the wifi card. It's a broadcom 4328 a/b/g/n/bluetooth card and it was using the broadcom-wl driver. Earlier today i plugged in an usb wifi adapter to test whether it worked on suse plug and play. Well after plugging in and using this wireless adapter, my internal wifi card is no longer visible to the system. I've tried lspci and its not displayed. I booted into a different suse install and it wont work there. My bios does not seem to have a disable feature and the killswitch is in the correct position. The bluetooth is working but the wifi is not. In lspci i used to see "hp integrated (wireless+bluetooth)" and "broadcom 4328..." but now only the former.
View 9 Replies View RelatedFor those of you that prefer open-source solutions, the b43 code to drive BCM432X 802.11n devices has just come to life. It can now scan and associate. Tests for throughput will come soon. These revisions to the driver will be in kernel 2.6.38, thus not in openSUSE until the next release after 11.4.
View 1 Replies View RelatedI have been trying to get my Broadcom BCM4328 to work properly on openSUSE 11.2 (kernel 2.6.31.5). Finally, after installing the wl kernel module, I managed to get it working when a run the following commands after a reboot:
sudo /sbin/modprobe -r b43 b44 ssb wl
sudo /sbin/modprobe wl
sudo /sbin/modprobe b44
sudo /etc/init.d/network restart
My question is how can I automate the above commands, i.e. create a startup script to initialise the wireless adapter properly without the need to manually reload the kernel modules?
Well I see there is a lot of people which have problems with BCM4312 I read that topics but my problem kind of different..I installed 11.3 few day ago at my job. Everything was just fine...First of all I'm installed firmware
Code:
install_bcm43xx_firmware
Wireless worked fine...
[code]...
I have an Acer Aspire 3003LMi and BCM4318 card and installed opensuse 11.3 on the laptop.Please if someone does or knows how to make wifi work.
View 9 Replies View Relatedi'm having a lot of trouble getting my wifi to work on my dell inspiron e1405 laptop. I looked through the forums and tried a few solutions to no avail
View 9 Replies View RelatedI installed openSUSE 11.3 under 2 machines, one of them using a Linksys USB wireless N adapter (rt73usb) and another using an Atheros AR5001 Wireless Network Adapter (ath5k). I have a Belkin f5D8236-4 router, with the SSID "linksys". I also have an Ubuntu 10.04 machine which has working wireless internet. I know almost nothing about networking, but from what I can tell, openSUSE 11.3 seems to have trouble with DHCP, specifically setting the dynamic IP address. To try to go about fixing this, I attempted to set a static IP, but I am quite confused by all the settings.
I have tried both the graphical "Network Manager" (KDE, Gnome, and command line versions) and ifup, both with no luck.
Here is the information from the working Ubuntu machine code...
Last week used lxde11.3 and no problem connecting. Today I switched to xfce11.3
and the wifi card is registering fine as connected but it doesn't send the key out
apparently to register the connection to the modem so it is fully activated.
I think lxde had a network manager but in xfce here I'm using Yast. What mismatch
do I have here ? How do I start a network manager so the key will connect ?
After instalation of Suse 11.4, wifi worked totally correctly, until the first restart. Then it ceased to work. It looks like everything is working correctly until WPA authentication.
My wifi device
Code:
So until now it looks for me that everything works correctly, but after trying to connect the problems begin.
dmesg output:
Code:
So the wlan interface authenticates, and then disauthenticates by local choice? a bit about the reason points to wpa_supplicant. Many peoples report that they have multiple copies running, and killing them solves a problem. Sadly I've only one copy, and after being killed it restarts.
Here is wpa_supplicant.log on the first run after install(when it worked)
Code:
And here is log of what happens after restart:
Code:
I've no way to change from WPA authorization.
i have an Acer aspire 4920 laptop with opensuse11.3 installed and wifi card has identified home wifi, but for some reason when i enter the wpa-psk key it doesnt connect.i have been at this problem for several days and scanning the net for answers, without joy.i dont know about the command or terminal line, i have tried to type in commands but i get no joy.
View 4 Replies View RelatedI just installed 9.10 and I can't detect any wireless networks. Is the card compatible with 9.10? Do I need to install any drivers? If the card isn't compatible with 9.10 is it compatible with later versions of Ubuntu? Marking this as somewhat urgent as I need to get internet access for some coursework soon, and also because my parents will kill me if they find out I've done anything unusual with the laptop because it's new and they think anything non -MS is a virus.
View 9 Replies View RelatedCan't get my WiFi to work on my HP. My WiFi chip is bcm4303 (rev. 2) this is a new thread from http://ubuntuforums.org/showthread.php?t=1400427&page=4 ) So, I reinstalled Ubuntu (fresh install) Activated the Broadcom b43leagacy Wireless driver. When rebooting, the WiFi LED on the On/Off switch blinks.
[Code]...
I recently got a lenovo w510 laptop and I installed openSUSE 11.3 KDE on it. the wireless works fine at home (802.11g WPA2) when I go to work I have tried to set up the wifi for the 802.1X PEAP network but it doesn't look like it even tries to connect.
The work network set up is as follows. non-brodcasting SSID (do I need to tell network manager of this? I manually enter the SSID no problem)
Dynamic WEP 802.1X
PEAP
blank anonymous identity
no CA cert (I suspect this might be the problem)
PEAP v 1
MSCHAPv2
I have verified my username and pw several times, as well as the SSID. Just yesterday I helped a co-worker get on the network under ubuntu and it worked like a charm.
The Hardware profile displays the wifi card as a "WiFi Link 6000 Series" It is an intel card.
I decided to start of with Debian. I'm having trouble getting my wireless connection to work. I think i need drivers or something, i can't make a wireless connection. And it is a bit difficult for me, as i am new to Linux, and I'm not sure what I'm doing when i am writing these commands.
My wireless card is a Broadcom Corporation BCM43142 802.11b/g/n
I have been using Raspberry PI a little, so i am familiar with the terminal.
I'm working on Lucid, in HP Pavilion 9730us laptop.
My wireless broadcom card was working just fine until now as i installed it with the Hardware Devices manager, Today i put a new ALFA AWUS036H usb card to work with aircrack. both cards were working together for a while, but as i started playing around with aircrack the broadcom card of the HP has stopped working.
I made a mistake and followed the aircrack tutorial for R8187 / ieee80211 stacks driver, while i'm using RTL 8187 / mac80211 stack drivers, and blacklisted the RTL8187 , rebooted and then both card didn't work. I un-blacklisted it, and the ALFA is working but the broadcom not!
iwconfig shows me only one wireless card on wlan0 the blue light showing activity in the HP card doesn't go on.
Tried to uninstall and reinstall broadcom drivers, still no change.
I've just installed Ubuntu on 2 computers, and I'm new to it. However I'm not new to computers. The problem I'm currently running into on one of the computers is that the wireless will not detect any connections, despite there being many. The computer is a HP Compaq v6203AU using the wireless card Broadcom BCM4312 [14e4:4312]. I've went through dozens of walkthroughs, encountering errors in every single one of them, I've spent 8 hours on this one problem and extremely frustrated. It seem to be a problem with the driver that comes as default, and I'm lost at what to do.
The terminal command "lspci -nn | grep 14e4" returns the following:
03:00.0 Network Controller [0280]: Broadcom Corporation BCM4312 802.11a/b/g [14e4:4312]
ifconfig returns the following:
eth0 Link encap:Ethernet HWaddr 00:23:8b:b2:ab:d3
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:20 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:96 errors:0 dropped:0 overruns:0 frame:0
TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:7072 (7.0 KB) TX bytes:7072 (7.0 KB)
The computer has no internet access as there is nowhere to connect except through wireless.
I regret updating to 11.04. It broke everything during the update. I cannot get the broadcom wireless chipset to work more than 10 seconds, No matter how much research I do here. I have not been able to work within my GDocs for the last three days. Can I restore back to my 10.10 settings? I have an acer laptop.
View 3 Replies View Relatedwhen it comes to openSUSE but I am earnestly trying. I installed the openSUSE OS on my HP dv6000 laptop, but it does not seem to recognize my wireless card (which is a Broadcom 4311).
View 7 Replies View RelatedI'm happily using OpenSuse 11.2/KDE on my laptop equipped with a Broadcom BCM4311 WLAN chip, but today, after a restart, WLAN ceased to work. I mean that Network Connection doesn't show anymore available WLANs. Two things that seem strange to me are that the
[Code]...
I have this problem with my wifi for 2 weeks now.It used to work great and after some updates the Network Manager keeps rejecting my wpa passwords. The wifi card is working (tested with other OS's) and the wifi light on my HP laptop is on. I have installed broadcom drivers.The problem is similar with this one here but changing from default kernel to desktop didn't work in my case. have already read through Getting your Wireless to work and Broadcom instructions
View 7 Replies View Relateddell laptop and went out on thenet looking for a solution for my failed wireless interface. i downloaded the firmware but then my interface still fails to come on after a reboot.
wlan0 IEEE 802.11bg ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
[code]...
I recently bought Dell Studio 15 laptop, installed OpenSUSE11.2/64 in addition to Win7 64 bit. I am trying to connect it to my wireless network at home and at work, but without much luck.
1)Found out that Dell 1520 WLAN adapter has Broadcom 4353 chipset.
2)saw that b43-fwcutter installed
3)installed broadcom-wl and broadcom-wl-kmp-desktop
After that can see many wireless Access Points at home,selected one via NetworkManager (eth1), configured it (incl. security same as in Win7), it goes from Activating to Active, but I still can not connect - I mean, in the FireFox - "page not found"
iwlist scan (for my desired AP):
Cell 03 - Address: 00:E0:98:FA:5D:1A
ESSID:"Blackhawk"
Mode:Managed
[code]....
I can easily connect to WLAN at home and at work in Win7.
I can't get the wireless to work on my laptop its a hp Pavilion dv9700 it has a Broadcom 4321AG 802.11a/b/ g/draft-n Wi-Fi Adapter i cant seem to get it set up.
View 6 Replies View RelatedWhen I installed openSuse 11.4 it doesn't see my wireless card Broadcom. How can I install Broadcom wireless driver ?
View 9 Replies View Relatedget WIFI working on my Dell D600 with Ubuntu 11.04 freshly installed. I some limited sucched following the this post t=1621331 this got the card working but it was very very slow over 70% packet loss to the WIFIrouter. 1. Machine details Dell Latitude D6002 Wireless Broadband and Chip setlspci -nn | grep Broadcom - 02:03.0 Network controller [0280]: Broadcom Corporation BCM4309 802.11a/b/g [14e4:4324] (rev 02)3. Check interfaces
eth0 Link encap:Ethernet HWaddr 00:0b:db:e0:1c:5b
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[code]...