Ubuntu Networking :: Broadcom Laptop Wifi Card Driver?
Mar 9, 2011
I have an emachines D620 laptop running Ubuntu 10.10 with a Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01). I havent done anything with it and cant seem to get it to work. I know this because when I had visto on it the card worked, but know it says that its firmware is not enabled and ive tried installing the drivers using the Additional Drivers under Administration. I would like it to be working so I can use my laptop's internet.
View 5 Replies
ADVERTISEMENT
May 12, 2011
get WIFI working on my Dell D600 with Ubuntu 11.04 freshly installed. I some limited sucched following the this post t=1621331 this got the card working but it was very very slow over 70% packet loss to the WIFIrouter. 1. Machine details Dell Latitude D6002 Wireless Broadband and Chip setlspci -nn | grep Broadcom - 02:03.0 Network controller [0280]: Broadcom Corporation BCM4309 802.11a/b/g [14e4:4324] (rev 02)3. Check interfaces
eth0 Link encap:Ethernet HWaddr 00:0b:db:e0:1c:5b
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[code]...
View 5 Replies
View Related
Sep 16, 2010
I cant seam to find out how to get my card to work i cant find out how to install the driver or finding the wifi card on the system.
View 9 Replies
View Related
Mar 3, 2011
I have a HP Pavilion dv6-2155dx Entertainment Notebook with Broadcom Wireless Lan Driver.
I didn't want to bother anyone with this, but I just could't find a solution. I was happy using Ubuntu 10.04 LTS Desktop Edition, because the wifi was working fine, but I messed everything up dealing with networking in terminal.
So formated and now I have Ubuntu 10.10 Netbook Edition, but that didn't solved my problem at all, because my wifi driver still unfunctional.
Before anything, I tried commands like "dbus restart" and "network restart".
So after reading that I can install by getting ndisgtk and the .inf file, I downloaded the right driver from HP Support's page of my notebook. Extracted the package with Wine (got some error because I wasn't running Win7, of course, but that doesn't matter.).
I did this: [url]
And this is my final result:[url]
Technical informations:
Quote:
View 1 Replies
View Related
Jun 16, 2011
I just installed 9.10 and I can't detect any wireless networks. Is the card compatible with 9.10? Do I need to install any drivers? If the card isn't compatible with 9.10 is it compatible with later versions of Ubuntu? Marking this as somewhat urgent as I need to get internet access for some coursework soon, and also because my parents will kill me if they find out I've done anything unusual with the laptop because it's new and they think anything non -MS is a virus.
View 9 Replies
View Related
Dec 13, 2010
I installed Ubuntu 10.10 amd64 online today. I was using 10.04 32-bit before, and the network drivers were easy to find and install. Ubuntu did the job for me and they worked flawlessly. It was a relief I didn't need to search around.
Even though 10.10 (64bit) found the drivers for me, both ethernet and wireless, they do not seem to be working alright. I installed both, made a restart. I found that the WiFi light on my laptop stays on, even if the wireless network is turned off using either the key combination (Fn+F2), or manually turning it off.
Issues with the ethernet? I am right now using ethernet but it does not care to detect the connection. Empathy won't connect automatically as a result- says no network connection. But here I am, posting this. Evidently, there is a connection, right?
Issues with the wireless? The WiFi light stays on all the time, and it isn't able to get hang of the connection I have at home. It just won't show any wireless connections available. When I tried to connect by giving it the SSID and the encryption type and password, it didn't work. Just kept asking for the password again and again (I have checked with the router- the password is correct).
View 2 Replies
View Related
Feb 24, 2010
I am using a Fujitsu Amilo pi3560 with a Realtek rtl8172 wireless card, and running the latest driver (rtl8192se_linux_2.6.0014.0115.2010). The OS is Ubuntu 9.10.
Everything runs perfectly - when my laptop is connected with the power cord. But when I go battery the wireless disconnects after a few minutes. It then asks for the wpa password, searches for the router, asks again, and so on indefinitely, until I reboot and it all replays once more.
View 2 Replies
View Related
Apr 29, 2011
I recently bought a HP g62x laptop for myself. It sports a decent Core i3 processor, 4 gigs of RAM and a 500GB HDD. It also came with Wireless-N, a real bonus because I am using a Wireless-N router. The chipset is a Ralink 5390. It came preinstalled with Windows 7, and everything works fine in there (obviously).
I then proceeded to install Ubuntu 10.10 x64 a few days ago (this is before Natty came out) and everything worked . . . except WLAN. So I plugged in via Ethernet and went looking and found that I clearly wasn't the first to discover this issue. I found a guide here that I followed to download the Ralink Linux driver (which is stated to support my chipset), configure, compile, and install. Everything went perfectly, I restarted; lo and behold, I have a list of access points. I went to connect to mine, entered the password, and now the animated "WiFi wave" logo keeps going indefinitely until you click it, and it freezes for a few minutes. It will unfreeze if you let it sit but clicking it causes the same freeze again.
I couldn't really care less about a WiFi icon freezing, but a.) it freezes everything else in the system up, not just the icon, and b.) it never actually completes the WiFi connection. I really, really don't want to be forced to use Windows because of a crappy WiFi driver!
Since Natty came out I installed that and I can't even compile the driver without fatal errors, so I reverted to 10.10 and everything is the same as it was before. Note that this is a clean Ubuntu 10.10 Desktop Edition 64-bit install, nothing updated/modified/changed besides (attempting) to install this driver.
View 1 Replies
View Related
Jul 13, 2010
I'm sure you've seen this question before -- I tried searching but I can't find a clear answer. All I need is to get my wifi up and running in Ubuntu 10.04. I'm currently double-booted with XP on a Dell Latitude E5400 laptop. I'm in Windows right now. I can't post my lpsci readout because I can't access the internet from Ubuntu -- no access to wired connection.
I worked on this problem for a long time last night and fixed it somehow by installing a driver program -- it had "cutter" in the name. Today, however, I try to log in and Ubuntu won't connect to an open wifi point. Boot #1 it recognized it but wouldn't connect. Boot #2 it wouldn't recognize it at all (said "wireless is disabled" even though it wasn't. Boot #3 it would recognize the wifi point but wouldn't connect.) I can mantain a constant connection to this wifi in Windows XP and also on my Android phone.
I just want someone to please tell me how to get my wifi working reliably. I'm excited to switch over to Ubuntu, all I need is for the wifi to work. My wifi card is a Broadcom 43xx (4312?). Something like that.
View 10 Replies
View Related
May 2, 2010
I've been using Ubuntu for a few years now and in general am very pleased with it; it's Achilles Heel is however WiFi.My daughter has an older HP laptop with built in Broadcom wifi, Lucid did not recognise this, neither did it recognise a Netgear PCI card or a Netgear USB adapter.Network manager showes wifi greyed out.lspci -vnn shows BCM4303 802.11b [14E4:4301] (rev 02)lshw shows *-network:1 UNCLAIMED and shows product as BCM4303 802.11b wireless LAN controller.Wifi is the most popular connection method for the average user, until it is made simpler to resolve problems a lot of potential Linux users
View 3 Replies
View Related
Jan 24, 2011
I just bought a Lenovo B560, everything working except the Broadcom 4727 wireless (only in terminal it works)
View 4 Replies
View Related
Jan 12, 2010
I just got my new ubuntu 9.10 os desktop version installed into my lenovo laptop but then my WiFi is not working. Previously I had a broadcom driver which currently is not functioning with the ubuntu 9.10.
View 2 Replies
View Related
Mar 14, 2011
As a part of my final project,i am beginner and this is the first one that i have the opportunity to work under linux fedora,my task consist to develop with C a driver of wifi by using the SDIO Wifi card as an interface. This driver will be included in a digital receiver TV.
View 2 Replies
View Related
Oct 29, 2014
I am having a problem with the driver, I do lspci | grep -i net and this is my driver: Broadcom Corporation BCM4321 802.11a/b/g/n...I have tried this: URL.. (I have debian squeeze) and it created a eth1 interface.I do ip link set eth1 up and after that I do : iwlist scan and it works, but when for example I try iw dev eth1 scan it doesn't work it says nl80211 not found.And when I try to run hostapd (which is my final goal) it also says nl80211 not found.
View 1 Replies
View Related
Mar 28, 2011
i am using fedora 14 in my lenovo z560 laptop. It contains broadcom wifi card. The configuration is.Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g LP-PHY [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] I want to inject monitor mode in my laptop to run kismet . But i can't. I installed broadcom-wl driver in my laptop but i think its not compatible to run monitor mode..
when i run kismet it show me error that :------ try some other open source kernel driver And the other is :- kismet find only binary value eth1 port. It isn't detecting wlan0 port
View 10 Replies
View Related
Apr 5, 2011
I recently installed Suse 11.4 on my Dell Latitude 2110 netbook using the KDE live distribution, and, after that, the Broadcom wireless ceased to work. To enable the wireless connection, I have to press Fn + F6. If I do it now, the wireless led indicator turns on for a couple of seconds, then turns off again. Moreover, the option to enable the wireless connection in the network manager is greyed out
lspci output:
Code:
0c:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01)
iwconfig output:
Code:
wlan0 IEEE 802.11abgn ESSID:off/any
Mode: Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit: 7 RTS thr: off Fragment thr:off
Encryption key: off
Power Management: off
dmesg output:
Code:
[8.330963] brcm80211: module is from the staging directory, the quality is unknown, you have been warned.
[8.362403] brcm80211 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[8.362422] brcm80211 0000:0c:00.0: setting latency timer to 64
output of rpm -qa | grep broadcom:
Code:
broadcom-wl-kmp-desktop-5.100.82.38_k2.6.37.1_1.2-7.pm.8.1.x86_64
broadcom-wl-5.100.82.38-7.pm.8.1.x86_64
View 9 Replies
View Related
Nov 29, 2010
Here are the specs for the computer in question:
Distro: Mint 10 Julia Gnome
Dell Inspiron 1100
2.40 ghz Intel Pentium 4
8 kilobytes primary memory cache
512 kilobytes secondary memory cache
20 GB HDD
1 Gig MB RAM (2 512mb sticks)
Linksys Wireless-G Notebook Adapter WPC54G V3
CDRW/DVD Optical Drive
From the title of this post, you can see that I am having some trouble getting the Linksys Wireless-G broadcom card working. I have been doing some research and have heard that getting a broadcom card to work in Linux can be a real pain.
I have verified that Mint 10 recognized PCMCIA so I am good there. I installed Wifi-Radar to see if maybe it would recognize it but it did not.
When I type iwconfig, it does not show any wireless signals available. When I originally set up the partitions for this laptop, I used PartedMagic and was able to quickly set up the network on that with vertually no problem what so ever.
View 6 Replies
View Related
Sep 28, 2010
I'm about to install OpenSuse 11.3 gnome on my laptop with ubuntu & vista in a dualboot, and wanted to make sure that the Broadcom 4322AG wireless card would be compatible with my laptop.
View 2 Replies
View Related
Mar 27, 2011
I recently installed suse 11.4 x64 onto my hp tx2000 tablet. everything has been working great including the wifi card. It's a broadcom 4328 a/b/g/n/bluetooth card and it was using the broadcom-wl driver. Earlier today i plugged in an usb wifi adapter to test whether it worked on suse plug and play. Well after plugging in and using this wireless adapter, my internal wifi card is no longer visible to the system. I've tried lspci and its not displayed. I booted into a different suse install and it wont work there. My bios does not seem to have a disable feature and the killswitch is in the correct position. The bluetooth is working but the wifi is not. In lspci i used to see "hp integrated (wireless+bluetooth)" and "broadcom 4328..." but now only the former.
View 9 Replies
View Related
May 27, 2011
How to use the BRCM driver for this following wireless cards?
BCM4313
BCM43224
BCM43225
Seems the since the 2.6.37 kernels it would be included. And wouldn't be necessary to use Broadcom STA linux driver anymore.
View 2 Replies
View Related
Aug 21, 2011
I need to install b43 driver for my bcm4315 wifi card. I herd that bcm4315 need a firmware called firmware-b43legacy-installer is needed to do this.So how can i install the driver...I have installed it once and when i am trying to activate it using ubuntu drivers and install it shows error system error:archives failed().
View 4 Replies
View Related
Aug 29, 2010
I'm very new to Debian (and Linux in general), and am currently taking a Linux course at college... I'm trying to get Debian running on my MacBook Pro (late 2009 model) and it's been complicated but I've got the operating system installed on it... I'm just having a few problems, the biggest right now of which is my wireless card, which doesn't work. So, I found instructions on the Debian Wiki for getting the driver for it, but it's not compiled already and I have little knowledge of manually installing stuff through Linux...
View 2 Replies
View Related
Dec 4, 2010
Just installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
View 6 Replies
View Related
Feb 20, 2010
I have Centos5.4 loaded on a late 2008 MACBOOK Pro and would like to get wireless working. I've attempted to download the broadcom driver and create a driver module with no luck.
Using these instructions....
[url]
When I make the WLAN driver, I get this:
View 2 Replies
View Related
Sep 12, 2014
I'm a brand new user of Debian, and I just bought a (too much?) new laptop, the HP 430 G2. It seems to work great for almost everything, except that I don't have any wifi available.
I tried so many different things (without any success) that it would be hard to resume. But for now, all I have is a new installation (to avoid parasite installations of weird things), and a kernel updated to 3.16. I don't know if it's useful though...
Some information from my system :
Code: Select allbonyhoax@bonybook:~$ sudo ifconfig
[sudo] password for bonyhoax:
eth0 Link encap:Ethernet HWaddr 14:58:d0:09:72:bd
inet adr:130.125.57.144 Bcast:130.125.57.255 Masque:255.255.255.0
adr inet6: fe80::1658:d0ff:fe09:72bd/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:27329 errors:0 dropped:0 overruns:0 frame:0
TX packets:3491 errors:0 dropped:0 overruns:0 carrier:0
[Code] ....
The first element I notice is that I don't have the line with "Kernel driver in use...". Which seems to indicate that there's a problem with the kernel module (is that right?). But I don't know how to fix it...
The other thing that puzzles me with these last two commands is that according to this page, my wifi card is a Broadcom BCM43142. But it's not the result I get with the lspci command.
Anyway, I'm really lost, I don't know what to do, what to check, what to install. I don't want to go by random, testing all the different solutions I see on the web blindely. This is the reason why I ask it here.
View 7 Replies
View Related
Apr 17, 2011
I have just moved to fedora from ubuntu.i am trying to install wifi netword driver on my laptop but its not helping me.I have Dell inspiron 1545 with Broadcom Corporation BCM4312 802.11b netword card.i'm unable to find firmware package for my network card. what should i do to use wifi netword on my laptop? where to find and install the driver to activate wifi on my laptop?
View 10 Replies
View Related
Jun 27, 2011
Im using natty in lenovo b460. After installation was not able to connect to wifi. Ethernet is working alright. So searched for additional drivers and installed the Broadcom 43xx drivers. After restart the network applet says the wireless is disabled by hardware switch, even after it is switched on/off several times.
Lenovo B460
kernel:2.6.38-8-generic 32-bit
Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
ubuntu 11.04
[Code]...
View 1 Replies
View Related
Jan 14, 2010
I have a Laptop PC Acer Aspire 1710 and OpenSuse 11.2 installed on it I tried to setup my wifi card but it doesn't workI checked the log system log file.Apparently the driver cannot be loaded :
<6>[ 8.556483] b43-pci-bridge 0000:03:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
<6>[ 8.560204] ssb: Sonics Silicon Backplane found on PCI device 0000:03:03.0
<6>[ 8.581966] cfg80211: Calling CRDA to update world regulatory domain
[code]...
View 4 Replies
View Related
May 4, 2011
I am running (K)Ubuntu Lucid 10.04 64bit on a Dell Latitude E6400, WiFi Card Intel 5100. Never had any problems with networking. Up to about 2 weeks ago. I do realize there have been quite a few posts with this network adaptor, but non really described the problem I have here.
What happens is that suddenly the WiFi LED on the computer stops blinking, the WiFi connection gets disrupted, and the device is not recognized anymore when checking ifconfig. Only cold restarting the machine helps then... it will work for a while (between 1 and 20 minutes) and then crash again.
On Windows 7 the card works perfectly fine. With Ubuntu 11.04 in Live CD mode I have the same effects (connection crashes after a while). Also tried booting an older kernel, no success.
My exact hardware:
Code:
I notived the following problems in /var/log/kern.log
Code:
View 4 Replies
View Related
Jan 17, 2011
anyone tried to run wifi-card based on this chip? In coming days I will build myself a proprietary driver for 2.6.27.7 kernel. I mostly aware about patches for wpa_supplicant. Should I use a source for wpa_supplicant from slackware 12.2 distro or a new version? Do you know about any other prerequisities (requirements, dependencies) for building this proprietary driver?
View 2 Replies
View Related
