I just put 10.10 on my D830 and I love it except for a delay when I'm using the internet. When I click on a link while surfing the web it takes about 13 seconds before it responds. After that it works just fine.
My Windows 7 PC and my Macbook Pro don't do that so I'm guessing it has something to do with Ubuntu.
I've already got the b43-fwcutter package and a driver called 'b43' appears in System > Administration > Hardware Drivers but it does not seem to enable. Another, Broadcom STA wireless driver, does enable, but I'm not picking up the wireless signal.
Code:
$lspci 05:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 01)
08:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Code:
$ sudo lshw -C network
SCSI
[Code]...
I have a DEll Mini 9 - it has worked fine even though it has a limited memory. But Husband only uses to have a surf. It now wont connect to net. The Broadcom4312 Wireless Card is not working on Obunto. It has a Dell 802.11b/g Wireless LAN Mini card installed and Obunto Edition Version 8.04 Have phoned Dell and after several calls on Hold for over 15 mins each time and getting nowhere fast i am coming to you guys/girls. I am not a very good comp person, but i do get by and i am trying, so be gentle with me. in simplistic terms.
View 2 Replies View RelatedI have installed CentOS 5 just downloaded yesterday on a Dell D620. Everything but the wireless card works. So I found this article:
http://wiki.centos.org/HowTos/Laptops/Wireless/Broadcom
and followed it step by step and was able to complete all of the tasks. The problem is that obviously it still won't start. It is not even recognized as an adapter but when I run lspci -v it is there sure enough. When I look under the networking GUI it is listed there but it has no MAC assigned to it. Please let me know what command output you need to see and I'll get here asap. I have searched this forum and other sites and nothing so far has worked.
Wifi works on 11.3 with installed the broadcom-wi & broadcom-wl-kmp-desktop,but this trick doesn't work on this new 11.4.
View 9 Replies View RelatedIm having problems making my wireless card "Broadcom 4312" work on centos 5.4 X64 , i have installed and built the driver from their official site and inserted its module successfully, but whenever i try to avtivate the interface "called eth1" i get the following
Error for wireless request "Set Encode" (8B2A) :
SET failed on device eth1 ; Invalid argument.
Error for wireless request "Set Encode" (8B2A) :
SET failed on device eth1 ; Invalid argument.
ok basically i have a new dell inspiron n5010 with a broadcom 4313 wifi card. it doesnt work with ubuntu studio 10.10. I have the drivers all installed and it works on ethernet with the broadcom STA proprietry driver. if i disable this driver the eth doesnt work. but the driver shows its working (screenshot-1).
There is no pop up or anything in the task bar for detected wifi. i open the network settings and it shows up with a wifi option but i have to go into properties and manually type in what i have "the_den_meribel". which didn't work. (screenshot-2).
i have tried the other driver broadcom-sta-common and that doesnt make it work either. screenshot-3. i did try to install the "lp-pphhy" or whatever it is (seacrh for firmware-b43 in synaptic).
i have a list of results from what i have typed into the terminal: dell inspiron n5010
Code:
sam@drytopubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18)
[Code]....
I just installed the 64-bit Kubuntu 11.04 and i've been having some issues getting the wifi to work. At first I went to additional drivers and activated the STA driver and restarted. After restarting when I went into the network manager and any option for wireless was disabled.
[Code]....
After some serious trouble with Plasma, I decided to re-install 9.10. When booting up, I noticed that the wireless indicator light stayed on orange which usually means that the driver is not loaded.
I have a Broadcom 4312 in a HP Pavilion dv6. I checked the repository but no driver shows up. I seem to remember that it used to be there. Or am I mistaken and do I need to install the vendor driver from the Broadcom site?
I've added the output of lspci and dmesg | gre b43
HTML Code:
HTML Code:
I have an HP 2133 Mini-Note [KX869AT] with a Broadcom 4312 wireless card. I've had Ubuntu 10.04 on my machine for a few weeks now and everything was great until my wireless card abruptly stopped working. It doesn't detect any wireless networks,uch less connect to them. I tried reinstalling the proprietary driver, but that hasn't worked.
View 1 Replies View RelatedI've been stalking the forums for the past few days trying various fixes to no avail. I'm sorry for more clutter of this issue.
Here's what I have:
emachines e725 laptop, dual core T4400 Pentium, 64bit, running Windows 7 and just installed Ubuntu 10.04.
My ethernet port works for cat internet but wireless does not. My wireless appears but when I open browser no connection.
Here is my ifconfig:
i just got ubuntu yesterday and had to play around with some settings and the fw-cutter tool to get my wireless working and it was...although i upgraded the kernel to 2.6.32-25-eneric...and it stopped working. the simple solution is to use the previous kernelersion...the wireless works there, but thats just not good enough for me ... it recognizes my card is there it just wont connect. originally i was using b43 driver and now it does not show in the system>hardware drivers list only the sta driver does, although when i try to install and activate it i get the error message "sorry, installation of this driver failed.please have a look at the log file for details: /var/log/jockey.log"
View 5 Replies View RelatedI'm trying to start using Debian Squeeze 64b on my laptop, which is Dell Latitude D830 with Intel i965GM.
After Debian installation, when system should display some nice background and window which please me to log in, I see my screen gets blank, fuzzy, blank again, ...and after several times finaly all hangs. Surprisingly mouse pointer is displayed nicely and works. I can't use network on Debian becouse of windows authorization program which i can run in wine on KDE. This works on Kubuntu.
What I did already:
I installed KUBUNTU 10.04 LTS and it's doing job well.
I installed Debian Squeeze with options:
- enabled:base system, laptop
- disabled:graphical environment
After instalation I logged in on root account and did:
1. aptitude install xserver-xorg xbase-clients xfonts-base xterm
2. aptitude install kdebase kde-i18n-pl
3. aptitude install kdm
4. reboot
5. problem occurs
@2: Googling everywhere i found several installation guides pointing to instal pure KDE by installing kde-core package, but it seems Squeeze does not have it.
@3: Unfortunately this command did not install nor update anything.
All I want to do is to install pure Debian with xorg and kde core (not full kde package) for later customization.
I tried to:
- generate xorg.conf (X -configure) and place it at /etc/X11/
- use xorg.conf working for other people in web.
- dpkg-reconfigure xserver-xorg
- googling & forum search for my specific problem and for errors found in syslog; with no working solution.
The card uses a momentary switch to turn on at and off and it doesn't work. I read that there is a way to have the card turn on by default on boot but I can't figure out how to do it.
View 1 Replies View Relatedget WIFI working on my Dell D600 with Ubuntu 11.04 freshly installed. I some limited sucched following the this post t=1621331 this got the card working but it was very very slow over 70% packet loss to the WIFIrouter. 1. Machine details Dell Latitude D6002 Wireless Broadband and Chip setlspci -nn | grep Broadcom - 02:03.0 Network controller [0280]: Broadcom Corporation BCM4309 802.11a/b/g [14e4:4324] (rev 02)3. Check interfaces
eth0 Link encap:Ethernet HWaddr 00:0b:db:e0:1c:5b
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[code]...
How do you enable repos? Namely RPMFusion set? I have 2 repo's that are currently in stalled:
[root@dv5-1235 Joe]# yum repolist
Loaded plugins: presto, refresh-packagekit
repo id repo name status
fedora Fedora 12 - x86_64 enabled: 19,122
updates Fedora 12 - x86_64 - Updates enabled: 755
repolist: 19,877
I'm trying to get my Broadcom 4312 working again since FC10. I noticed that RPMFusion isn't listed. This would answer why I can not install Broadcom -wl.
I've been having some trouble with my recently bought laptop.
Type: Dell Vostro 1015.
You can see the full specification by following the link in my signature.
What's important is this code..
The system freezes randomly and all I can do is to push the power button and force-turn it off.
I'm not sure, but I think it's the wireless. It's my second Fedora install on this machine, and the second was all right until I set the wireless drivers (or I had luck to have no stops).
When I first had partitioned, and formatted appropriately, I installed the newest version of Ubuntu available (Time of posting 10.4), on the partition made with bootcamp, rebooted into Linux with rEFIt Now once I booted into 10.4 I got to the desktop, it started asking me about restricted hardware drivers, so I went into System > Administration > Hardware Drivers, It then searched for the drivers, it found the STA driver, and the B43 driver, I am unable to allow both. So I went on to try ndiswrapper, I downloaded it off another pc, compiled and installed on the iMac. then I got the driver off the Leopard install disk, put that on my flash drive, extracted the files from the installer, put that on the flash drive, then I went back over to the machine in question, copied the file to the desktop, I used the cd command to navigate to the folder, then ran ndiswrapper -i bmcwl6.inf, I made sure that the inf and sys files were in there, so I didn't know what was going on exactly.
So then I went into the software sources, and enabled the cd as a software source, then went into Synaptic, and installed the drivers, it said the install was successful, however when I go back to enable it, will still refuse to activate, I have looked all around for solutions, I have even checked out other threads on this matter. The funny thing seems to be, is that everyone, or almost everyone who has this card on their computer, are upgrading to 10.04, when it worked on a previous version.
Well I see there is a lot of people which have problems with BCM4312 I read that topics but my problem kind of different..I installed 11.3 few day ago at my job. Everything was just fine...First of all I'm installed firmware
Code:
install_bcm43xx_firmware
Wireless worked fine...
[code]...
I'm finding a hard time getting my wireless card to work, my laptop is a Dell Inspiron 1525 and this is all the info:
0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
0b:00.0 0280: 14e4:4315 (rev 01)
[ 8.375610] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
[ 8.390374] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 6, Type 5, Revision 1)
[ 8.390436] b43: probe of ssb0:0 failed with error -95
I'm reinstalling opensuse 11.3 with KDE. In previous setup I got it working. It is a fresh x64 install. Update all is done. Pacman repo added. code...
View 4 Replies View Relatedafter finally installing 11.3, I found that my wireless NIC had stopped working. I've spent about 4 hours trying various online tutorials to get the card working, but I'm still right where I was when I began. The card as reported by lspci:
[Code]....
I am running (K)Ubuntu Lucid 10.04 64bit on a Dell Latitude E6400, WiFi Card Intel 5100. Never had any problems with networking. Up to about 2 weeks ago. I do realize there have been quite a few posts with this network adaptor, but non really described the problem I have here.
What happens is that suddenly the WiFi LED on the computer stops blinking, the WiFi connection gets disrupted, and the device is not recognized anymore when checking ifconfig. Only cold restarting the machine helps then... it will work for a while (between 1 and 20 minutes) and then crash again.
On Windows 7 the card works perfectly fine. With Ubuntu 11.04 in Live CD mode I have the same effects (connection crashes after a while). Also tried booting an older kernel, no success.
My exact hardware:
Code:
I notived the following problems in /var/log/kern.log
Code:
I tried Ubuntu before and because the wireless kept giving me error i stopped using linux for a while and now i'm back to give it another try and hopefully stay with linux, so help me out please. thanks in advance.
lspci & lsusb
Code:
ahmad@ubuntu:~$ lspci -nn | grep Broadcom
0b:00.0 Network controller [0280]: Broadcom Corporation BCM4328 802.11a/b/g/n [14e4:4328] (rev 03)
ahmad@ubuntu:~$ lsusb
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[Code]...
I was praying a standard install of Ubuntu 10.04 would work out of the gate and I was wrong:- Looks like everything is working except for my wireless adapter, Dell E4300
@nix-laptop:~$ lspci | grep "Wireless"
0c:00.0 Network controller: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller (rev 01)
@nix-laptop:~$ lsusb | grep "Wireless"
@nix-laptop:~$ lspci -nn | grep "Wireless"
0c:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01)
[Code]...
When I freshly installed my Ubuntu 10.04, broadcom wireless worked after I installed the driver using hardware manager. But somehow it got de-activated, and not its not working. I need help related to that. Here is some output which might help you to understand the problem.
Code:
paras@ubuntu:~$ sudo lshw -C network
[sudo] password for paras:
*-network DISABLED
description: Wireless interface
[code].....
I just got a new laptop...Dell Vostro 3500. Took off Win put on Ubuntu...all went fine. I did all updates and app downloads using my WIRED NETWORK as wireless wasnt working. However I was more interested in setting up the new computer. Anyway so after all is installed up pops "Broadcom STA Wireless driver" Proprietary driver do you want to install. Obviously I said yes...
Well now My wireless is working great but for some reason my Wired (auto eth0) no longer works. It just says disconnected and its grayed in. I'm pretty much a newbie but did try a few things like:
apt-get update
apt-get "something" essential (thats not a command just from memory it was something like that)
However I've had no luck. This Broadcom driver seems to have knocked out my wired network.
Im using natty in lenovo b460. After installation was not able to connect to wifi. Ethernet is working alright. So searched for additional drivers and installed the Broadcom 43xx drivers. After restart the network applet says the wireless is disabled by hardware switch, even after it is switched on/off several times.
Lenovo B460
kernel:2.6.38-8-generic 32-bit
Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
ubuntu 11.04
[Code]...
I have a Dell Studio XPS 1640. The wireless card is a Broadcom Corporation Device 4353, and I'm using the Broadcom STA driver suggested in System>Administration>Hardware Drivers. Every couple of minutes, it disconnects from my network and then it spends several minutes reconnecting and gives me the "Authentication required by wireless network" prompt several times. The problem only exists in Lucid: it goes away when I use a Karmic live CD, and a similar XPS computer with perfect wireless performance in Karmic has the same problem when I run Lucid on that one. Aside from downgrading to Karmic, how can I fix this?
View 9 Replies View RelatedI have an emachines D620 laptop running Ubuntu 10.10 with a Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01). I havent done anything with it and cant seem to get it to work. I know this because when I had visto on it the card worked, but know it says that its firmware is not enabled and ive tried installing the drivers using the Additional Drivers under Administration. I would like it to be working so I can use my laptop's internet.
View 5 Replies View Related