Ubuntu Networking :: Can't Get Squid3 To Work With 10.10
Mar 12, 2011
My home LAN (6 computers) is connected to a Dlink 624 router (192.168.0.1). All machines have DHCP addresses exception of the Ubuntu 10.10 box which has 2 NICs (192.168.0.198 and 192.168.0.199) with static IPs.
I've been spending hours reading stuff on Squid3 and I can't make it work, the client computers won't connect to the Internet.
What I'd like to do is a simple Squid proxy to cache the websites I access the most.
Would someone have in hand a squid.conf file compatible with my needs or suggest me another proxy product (with a GUI if possible,)?
I can't figure out how to get Calamaris to work. I'm using squid3, so I understand that there could be a problem with that, however I installed links for the logs, so that even though it uses "squid" it should work for squid3...
I even tried going into the /etc/cron.daily/calamaris file, and changing squid to squid3... But when I run the crontask, it gives no output and there's no file in /var/www/calamaris. What's going on? I need a program to analyze computer bandwidth.
I installed SQUID3 on a Linux machine with two ethernet interfaces (eth0 and eth1). I used the default settings in the squid.conf file and uncommented the two lines
Code:
And
Code:
eth0 is connected to a router, which provides Internet access. It is assigned an IP 192.168.1.2 by the router. I manually configured eth1 to have an IP address 192.168.5.1. It is connected to a switch. Systems having IP addresses 192.168.5.x are connected to this switch. I ran these two commands for NAT:
Code:
Code:
But when I try to access internet from a system having IP 192.168.5.2 through the proxy I get an error that says "Access denied". What is wrong with my configuration?
I have Squid3 running and SARG for producing report. I would like to see the hostname being logged in the access.log file instead of the client IP address. I have already set the option log_fqdn=on and it doesn't do it. I still see the client IPs in access.log files...
i'am trying to configure Squid3 et SquidGuard on ubuntu Server 10.04 for a school. I'm new in linux, before i post this thread, I searched in the french forum and www. I found nothing to help me to resolve this issue. You can see below to configuration file from Squid3. which is stored in /etc/squid3/
I haven't found any updated instructions for adding squidguard to the new squid3 server. I tried following the old instructions for doing this, making changes to the text to point to the new squid3 locations, but this didn't work.
I got squid3 installed on ubuntu server 10.4. I believe it is up and running as I can browse the internet on my other computers.I followed one of the tutorials on the net and looked at others for guide as well. Everyone of them did not mentioned that we have to create the swap files. Are we suppose too? I couldn't find the location of the swap file anywhere on the server.
i configured Squid3 server in my Ubuntu 10.04.Now the ip based and content based blocking is working fine.Now i want to configured bandwidth allocation of ip address and group ip address..pls give the solution
I'm kind of new to squid. I've looked at the proxy server using squidclient and am getting
Seems like a lot of cache misses is this normal?
I know there is stuff in the cache
Internal Data Structures:
It's wierd because misses looks like more than requests. I don't know if I'm reading this right.This is just a proxy on a home network with about 6 clients connected.
New to opensuse, trying to set up cache proxy and webfilter at a highschool. I have a new install of opensuse11.2 64bit installed as server. Installed squid3 stable. Trying to configure it in yast2. Now in yast2-->networkservices-->squid I get the message squid needs to be installed, continuing with Next I get message unresolved dependencies then another that squid3 conflicts with squid-2.7. Solutions offered are deinstall squid3 or don't install squid-2. I select the latter and get messages that yast might not function etc. Isn't squid3 the newer version of squid-2? Should yast2 recognize that?
I installed squid on my machine, and for a while it was starting up automatically when the computer would turn on, and I would only have to reconfigure on ip-up for the new dns, etc.Now for some reason, I notice that squid isn't even started.To fix this, I wrote a start up script in /etc/rcS.d/ that runs:/etc/init.d/squid3 startAnd I notice it still isn't starting.So I write "/etc/init.d/squid3 start" and put it in my ip-up.d/ script.Everything in the script is being executed, but the squid server.I've tried reinstalling squid... what am I missing? where does the computer start these services?
I run a Squid 3 server that is acting as a web filter. It worked fine on Etch. The system stopped working properly due to two of the three SATA cables being bad. Before I figured that out, I tried doing updates. Since Etch updates were no longer available, I did a distupgrade to Lenny. Immediately, Squid stopped working properly. It would take up to two and a half minutes for it to respond to a web request and add it to the access.log. This was using the same configuration file that it was using before the update.
After I found the hardware problem, I did a clean install of Lenny. I used the basic squid.conf like I did on the previous system, only changing it to add my ACLs and because it wasn't saving an access.log to the default location unless I uncommented the path directive. Now, it won't respond to a request at all. Forwarding is enabled and the firewall seems to be set up correctly.
I've setup Squid3 running on Ubuntu 9.04 64-bit server, and configured it to act as a transparent proxy and setup my router following these instructions: [URL]
Everything works great as far as browsing, but my main goal was to cache large downloads (usually executables) that I download frequently. So I set the minimum to 300KB and the max to 100MB. The problem, though, is the cache is not being used. I can download a file at regular speed on one computer, and then try and download it again and it downloads from the internet again, rather than the cache, so the speed is no faster.
i have successfully set up squid3 with squeeze using guide on this forum viewtopic.php?f=16&t=59301 . The only problem that i have is the size of /var/log/access.log is too big and keep increasing so i run out of free space. The size of it always the same size as my free space hard disk (so it make me run out of free space in just one day, it can have size to 30 Gb ) right now , the only workaround i make is using crontab to rm access.log every hour . I'm sure this is not the right solution . Does anybody know the correct workaround about this ? I have searching in google but seems havent yet have luck with this .
I am trying to set up my squid3 proxy as a transparent proxy - right now, I have to manually configure browsers to access via proxy. I understand that I have to put some rules into Iptables and also some further directives in the squid.conf.
I have a couple of specific questions. The proxy server is running on a Ubuntu 10.04 workstation and this machine also acts as a dhcp server for the network. I have just one subnet , namely 192.168.0.1-254 There is only 1 network card. Is it much easier to put in a second network card or is it just as easy to configure the existing lan card as a dual IP?
Is it necessary to configure these 2 IP's ( whether they are via 2 lan cards or dual IP on single card ) to be on different subnets. i.e ETH0 192.168.0.1 and ETH1 192.168.1.1 or is ok to have something like ETH0 192.168.0.1 and ETH1 192.168.0.254 ( where ETH0 is the one facing the LAN and ETH1 points to the modem router / switch i.e The Internet ) Where specifically do I save the Iptables rule configuration file and what must I call it ?
I actually have a server and a client.The client must connect to the server (via internet) to access to external websites. (You can see the attachment, maybe it's more clear )My actual problem is, I have configure Squid on my server, but I want to force SSL for the connection between the client and the server.I didn't really find nice tutorials about on that, maybe someone have an idea ? Or maybe some indications ?
I have this annoying problem since day one.I am testing out Red Hat RHEL5, everything is fine except DNS look up.If I ping www.google.com, it doesn't work, ping ip address it all works;if I bring up browser, put www.google.com it doesn't work, can't find the name, however, simply put ip address there it works.My DNS seeting seems ok, and the DNS works from Windows box.
I am trying to set up an unused machine as a web server for my students.
I originaly tried with Redhat 9 and had the same problems. I am using an HP Pentium 4 system with 2 network cards.
1) The built in Realtek RTL8139 configured as eth0.
2) An add in Broadcom BCM5782 Gigabit card that was added I presume when the built in card failed (we have a number of machines like this around the school), configured as eth1.
I did not realize the second card was installed when I had Red hat 9 on the system, but I discovered it after installing centos 5.5. I have tried to configure the system to use DHCP with and without getting the DNS from the provider, and both ways the system complains that there is no connection, check the cable, so it will not activate the device.
When I configure the device to use a fixed IP, I can configure the device, but I can't ping anything on the network other than myself. I suppose it is possible that both network cards have failed, but I get green link lights with both cards, when I connect them to my router, so I am at a loss as to why neither board seems to work. I don't have a spare network card to slide in because the computer takes a special mini card. Is there an easy way to test the board to see if the board is a problem?
I just started having a problem with my 10.04 laptop a few days ago, maybe Thursday, last week. When the computer is plugged into my home network (standard 192.168.1.1 sort of IPs) it works fine, but when I try to connect to my work network (130.15.90.XX) I am unable to pick up an IP. The router in my office is working fine, all the windows boxes can connect.
I've also noticed that when the computer is plugged in at work the notification icon for the networking indicates it is looking for a wireless connection (rather than the normal up/down arrows), even if wireless is deactivated
I can set a static IP in /etc/network/interfaces and everything works, so it seems to be a DHCP problem?
I've been experiencing a problem with Fedora in which when I enable Wireless in Fedora, Wireless networking does not work in windows. HOwever, when disabled, it works correctly. Windows claims it is "not able to find any networks to connect to"
EDIT: It seems that when wireless is disabled manually on fedora before shutdown, there are no problems in windows.
Networking on Fedora 11 doesn't work for me on various machines. Fedora 10 does, but only if you don't do an update.Why does Fedora get worse the more you keep it up-to-date?
I've been trying to set up an SSH key on my server and laptop. I generate the key on the laptop, copy the id_rsa.pub file over into '/home/server/.ssh/authorized_keys', and try restarting the SSH server on the remote machine (server). Every time I try to ssh into the server from the laptop, I get a password prompt.
When I created the key, I left the password blank. It is asking me for PASSWORD, not PASSPHRASE when I try to login. So, I would assume the key is not working/being recognized at all. I have tried changing the permissions of the ssh folder and authorized_keys file on the server per various posts I have found on the web. Nothing works.
i am using ubuntu 8.04. i have installed ns-2.34. i extracted it in the directory /home/bambos. i then wrote the following lines of code at the end of the bash file.
How to get my wireless to work. I'm currently running Ubuntu 9.10 on a Dell Inspiron 2200. The wireless adapter I'm currently using is a Linksys WPC54G ver. 3.
When I enter iwconfig lo, eth0 and wmaster0 have no wireless extensions. wlan0 says
I tried following the instructions here:[url]
But when I enter sudo ifdown eth0 it says internet eth0 not configured. then wlan0 it acts like it doesn't even exist.
I have a Compaq Presario with an Atheros AR5002 wireless card. I just installed Karmic and the wifi is the only thing not working. Wireless does work in 9.04. Here's what I get with iwconf
lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions.
