I just upgraded to karmic the other week and now my webcam isn't working anymore. here is my dmesg output
[Code]....
the last two lines are added whenever I try to run mplayer or skype on the webcam. We are currently using uname -r: 2.6.31-19-generic (64 bit), but the problem was the same on 2.6.31-17-generic
My Dell Latitude 2100 worked fine with the pre-installed Ubuntu 9.04. I upgraded to 9.10 and the touchpad stopped working. Restored to factory condition and it again worked fine. I re-did the upgrade, this time asking it not to delete the obsolete items.
View 3 Replies View RelatedI'm using the 10.04 Netbook Edition on an ASUS EeePC 1005HA. Earlier, I had 9.10 Netbook Remix installed. Under 9.10NR, the webcam worked wonderfully in Cheese. Once I upgraded to 10.04NE, the webcam became sluggish to the point where it is now unusable. In video mode it captures about 1 frame per five seconds. Under 9.10NR, it regularly captured 60 fps.
Did the driver package for webcams change significantly between 9.10 and 10.04? I can't think of anything else that would cause this issue due to an OS upgrade.
I tried upgrading from Jaunty to Karmic, which borked booting on that partition. I made a fresh install of Karmic on another partition which is booting fine, but I can't get Audio CDs to work, period. They worked in Jaunty and every release before that I had installed. Data CDs work fine in Karmic. I'm using plain ol' Ubuntu 32bit. I'm not sure where to start. There have been other threads where other people had identical symptoms. Either the problem went away mysteriously on its own, or they gave up because nobody believed them. In any case, I'm beginning to wish I had stuck with Jaunty.
View 2 Replies View RelatedI bought a Dell Inspiron with pre-installed ubuntu. All has been working for the last year and recently my integrated webcam stopped working. I was trying to use it on skype and it did nothing, although the program recognises I have a webcam, I tried cheese and the power light on my webcam comes on but again the screen does nothing.
View 9 Replies View RelatedI just upgraded from 8.10 to 9.10 and now my sound doesn't work (note: I don't know if sound was working on 9.4, since I only ran that long enough to upgrade again) Sound was working just fine under 8.10, and I just tried booting up with a livecd I had handy, which is 8.04.1 and sound worked right off the bat, no problems.I've checked the volumes on everything, including the master volume which WAS initially set to 0.Sadly, turning that up did nothing.The Pulseaudio Volume Control app seems to think nothing's wrong- it's picking up the sound from various applications just fine, the volumes are all on, etc. (aplay lists my soundcard fine:
**** List of PLAYBACK Hardware Devices ****
card 0: NVidia [HDA NVidia], device 0: VT1708B Analog [VT1708B Analog]
Subdevices: 2/2
[code]....
The problem i'm having is that my microphone stopped working after the upgrade to 10.10. Ubuntu doesn't seen any sort of input device any more, no line-in , no mic ( front as back ).Own on to the specs of my machine:It has a realtek ALC861-VD audio chip.2 mic jacks, 1 line-in , 2 out (front and back) and a coaxial port thing .The os is a upgraded from 10.04 to 10.10 and everything except this and my tv card sound works.I have pulse audio tools and alsa mixer ( although it broke during upgrade ) installed.alsa info is available upon request, so is any other info may you need it.
View 7 Replies View RelatedSummary: a long-working config involving a 1st-generation Ipod Touch with v1 firmware, Ubuntu, and Amarok 1.4 stopped working when I upgraded to Lucid.
A few years ago I was given a 1st-generation Ipod Touch, running the original v1 firmware (I never upgraded to the v2 firmware because v2 wasn't jailbroken at the time). I took it to a friend's place to activate and jailbreak it with her Mac laptop (I didn't have a Mac or Windows machine to install Itunes on; have been Linux-only for many years). Once jailbroken, I was happily able to use it with Hardy, Amarok 1.4, and ipod-convenience (which supply ipod-touch-mount/ipod-touch-umount).
This continued through upgrades to Intrepid and Jaunty. I didn't care for Amarok 2 in Jaunty, so I installed Amarok 1.4 from the ppa someone else made available. I continued to use it through Jaunty and Karmic, without any problems.
Last week I upgraded to Lucid. Syncing Amarok 1.4 to the Ipod Touch no longer appears to work; the Ipod fails to recognize any music transferred onto it (standard "No Music - you can buy music at Itunes" error screen), so I presume this is a libgpod/hash error. I have the FirewireGuid properly set in the .../Device/SysInfo file, as I always have.
Every time I use the Amarok Ipod "connect" function (which runs ipod-touch-mount) it tells me no valid Itunes db was found, and asks to initialize the db. I can then transfer music to the Ipod, and successfully disconnect, but it's not recognized on the Ipod after a respring or reboot.
I've tried RhythmBox and gtkpod briefly with no luck either.
Relevant installed packages:
Code:
ii amarok14 2:1.4.10-0ubuntu3~ppa5 Amarok 1.4 series
ii amarok14-common 2:1.4.10-0ubuntu3~ppa5 architecture independent files for Amarok
[Code]....
Edit: a little more info: after I let Amarok initialize the Ipod Touch and transfer a song to it, the iTunes.db that gets created on the Ipod is 0 bytes long. I presume this is the source of the problem, and indicates something is going wrong with libgpod's creation/editing of the db.
what I should do from here? I've tried removing the DB by hand, but it makes no difference - the subsequent operation to initialize the db results in the same 0-byte file.
I have used a quite obscure device called Cideko AK0b [URL] .... for quite some time now and it has worked perfectly for almost 2 years now, both in Wheezy and in Jessie. However since I made an dist-upgrade a while back the mouse has totally stopped working. The system works through wifi - strangely enough - but everything else works. Keyboard and gamepad buttons. The manufacture says the things doesn't work on linux and so far I have proved them wrong.
But now the mouse is just out right dead no matter what I do. Have looked into mouse autosuspend but no avail so far. My suspicion is systemd but that is as good as any guess.
Running 3.14-2-amd64.
This is my dmesg.
Code:
Select allroot@cryptserv:/home/dencrypt# dmesg | grep Cideko
[ 3.158099] usb 6-3: Manufacturer: Cideko Inc.
[ 3.469194] input: Cideko Inc. AK08b Device as /devices/pci0000:00/0000:00:12.1/usb6/6-3/6-3:1.0/0003:20E8:5860.0001/input/input2
[ 3.469329] hid-generic 0003:20E8:5860.0001: input,hidraw0: USB HID v1.10 Keyboard [Cideko Inc. AK08b Device] on usb-0000:00:12.1-3/input0
[Code] ....
Logitech webcam:
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[code]....
I've upgraded to 10.10. Before I did in 10.04 my webcam stopped working. I have an Acer AspireOne netbook ZG5 model. I want to use mousetrap with my webcam, so I would really like to have it back.
View 7 Replies View RelatedSuspend in Karmic has stopped working. It freezes the computer and I hard reboot is needed. Does anyone know of a solution?
View 1 Replies View RelatedToday my wireless has stopped working. I have a laptop hp6720s with network controller: Intel corporation PRO/Wireless 3945 ABG [Golan] Network connection (rev 02), dual boot vista/ubuntu 9.10, fully updated (kernel 2.6.31-17). I use a router edimax BR-6204 wg to use the net with other laptop. Till now i have using wicd for controll wireless without any problem, internet was quick and responsive. (Quick connection without any failure).
But today the internet was very slow and wireless starts to connect and disconnects intermitently, doing it unusable. This was what occured when i upgraded from jaunty to karmic and used the network manager from gnome, but then i fix the problem installing wicd. Now wicd behaves in the same way as gnome-network-manager. If i connect directly the computer to the router by wire, i have internet and everything works perfectly. How i can fix the wireless?. How i can do it works with ubuntu 9.10 and?.
I'm interested in buying a webcam for laptop/desktop computer. I'm using Karmic Koala and I will be using Skype. webcam that works out of the box with Karmic Koala and Skype.
View 2 Replies View RelatedI could play the particular DVD in the output below without problems yesterday. Today, totem just sits there and outputs these messages to a terminal:Quote:
~$ totem
libdvdread: Using libdvdcss version 1.2.9 for DVD access
libdvdnav: Using dvdnav version 4.1.3
[code]...
I'm currently running Ubuntu 9.10.After I updated to 9.10, my wireless connection stoppped working. I can access the network but I get no response or what so ever in my browser.Downloading language support or any software doesn't work either.Haven't changed anything to my settings and checked the router. Router works just fine.
View 7 Replies View RelatedI upgraded from 9.10 to 10.04 and my VMware stopped working. I got a message to recompile into the kernel. I followed the prompts and it was unsuccessful. I tried to uninstall and reinstall VMware getting the same error. See below an extract from the log file.Before you can run VMware, serveral moduels must be compiled and loaded into the running kernel.
stopped vmware services - ok
Error in log:
Nov 09 07:59:34.560: app-3077531328| Trying to find a suitable PBM set for kernel 2.6.32-25-generic.
Nov 09 07:59:34.560: app-3077531328| Building module vmnet.
Nov 09 07:59:34.560: app-3077531328| Extracting the sources of the vmnet module.
[code]....
On a fully updated Ubuntu 9.04 system, I had successfully configured wvdial to connect using a USB modem ("Update" brand) with an ID of 067b:0611 (uses the pl2303 driver module). In considering an upgrade to Ubuntu 9.10, I tried a LiveCD and was unable to connect using wvdial. However, because I had made the CD a couple months before, I went ahead with the upgrade (via the internet; not a fresh install) in the hopes that it would end up working or I would be able to find a solution for it.
The Problem: The upgrade was a success as far as I could tell, but when I tried to connect to the internet with wvdial, I was not able to. I checked the wvdial.conf settings to make sure they were the same as before, added some new ones I thought it might need, unplugged the modem and replugged it, restarted my system, etc., but all to no avail. Whenever I would try to run wvdial to connect, I would get the following output:
Code:
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
[code]....
This was different than the output I used to get with wvdial, but when I went over to my browser (Firefox) the internet worked fine. I'm assuming my email client and other things will work okay as well, but have not tested them as of yet.
A final touch I did to make connecting a bit less 'painful' was to right-click on the panel (at the top of the default Ubuntu screen), and click on 'Add to Panel'. Then I selected 'Custom Application Launcher', chose 'Application in Terminal' for 'Type', gave the launcher a name, pasted in that 'horrifically' long command line above, gave a brief description in the 'comment' box, then pressed 'OK'. Voila! I now have a launcher on my panel that with a single-click will bring up a terminal screen where I enter my sudo password and it connects. Then when I want to disconnect I just go back to that terminal, press Ctrl+C, which promptly disconnects me and causes the terminal to vanish into thin air.
Now, I don't know enough about this stuff to know why this command worked and wvdial didn't, but if you know, feel free to post a reply. Or if you'd like to see what settings I had for wvdial that worked in 9.04 but not in 9.10, let me know. Or if you think it's worth checking to see if this should be posted as a bug in either wvdial or Ubuntu, you can mention that as well.
I'm an Ubuntu/Kubuntu user for a while now and i hav Kubuntu 9.10 with ubuntu-desktop installed.
I have two hard disks and i had one of the partitions mounted automatically while startup. I did that by reading the first method posted here
HTML Code: [URL]
It was working good till i did the distribution update to Kubuntu 10.04. After the upgrade while startup, a message is displayed on the screen saying
Quote:
"Disk to be mounted at /media/miscellaneous is not ready or is not there. Continue waiting or press S to skip mounting or M for manual recovery"
I dont know what to do. I have to skip and then mount the partition manually. I think the entry i added in
Quote:
/etc/fstab
is still there.
Like many others it seems, my wireless has stopped working since a recent upgrade The answer does not lie in analysis of logs, settings etc. but surely with those who did it - they should provide a fix. I cannot believe everyone expects each individual users to go into their own analysis of why this is no longer working as it is clearly widespread. I have been using Ubuntu for 18 months without this problem on the same dual-boot laptop, and it still works on Windows as before, only Ubuntu 10.4 has recently stopped my network card from working.
I need to know when this will be fixed. I have been embarrassed by promoting Ubuntu to many colleagues who now also cannot work at home on their wireless networks. Seriously disillusioned I may start looking for a more stable alternative to Windows.
I updated my Ubuntu to Meerkat last night. everything seems to be working fine, except when i went to iplayer, it told me flash wasn't installed. I followed the link, and installed flash from APT source. In the software centre it is listed as installed. However, still cannot view flash videos.i have tried rebooting too.
View 2 Replies View RelatedI've just upgraded my Ubuntu version a week ago and got a problem that the Unity UI won't running after upgrade. My laptop is Dell Inspiron 14R which is i think is more than capable for running Unity 3D. When I rebooted after upgrade there was just a blank wallpaper screen, without Unity interface at all.
View 7 Replies View Relatedi have a dell 1501 that has been upgraded from 10.10 to 11.04. everything was working okay. and then the user ran an upgrade recently. subsequently the wifi has mysteriously stopped working. it connects okay if one plugs it directly into the router but the wifi seems to have just stopped working.my mini 9 connects fine to the netgear wifi router using wireless.when i run the system tests for networking i get the errors..."root could not find def gateway info /proc""root could not find default gateway by running route"here is the output from some diagnostic commands.NOTE:this is similar to a post titled "wi-fi dead?" but the output is not quite the same...
lauren@lauren-Inspiron-1501:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[code]....
After i upgraded to karmic i experienced that the sound of spotify was at times strange. When i started a new song there was some strange plucking sounds, can most be understood as the sound a old LP-player makes when there is dust on the record. Not much but more than enough that I can hear it and wish it wasn't there. After some time of playing the songs sometimes was totally distorted by "disturbance" and it became impossible to even hear that there was a song there. Like when you are out of reception of a radio channel.
I did some research and upgraded to the wine1.2 with "custom" pulsaudio drivers. Then the total distortion was gone, but the, always present, plocking sound still was there. I have tested adjusting PCM volume, have some volume on mono, upgrading to newer pulsaudio drivers. The same problem is when ever my dear computer i producing sound. Spotify,firefox, rythmbox and mplayer. I can't see any answers after spending some time on google. I hoped i could fix this without deleting and removing pulsaudio.
Dell Vostro 230 with integrated Broadcom NIC.
Wakeonlan was working just fine with Wheezy on this machine. After upgrade, wakeonlan will resume from suspend but not from shutdown.
I have no problem with other machines (same software setup) after upgrade. None of my other machines have a broadcom NIC.
No BIOS settings were changed during the upgrade. If I enter the BIOS on boot and make sure settings are correct then 'save' and shutdown, without booting to debian, I can then successfully wakeonlan. Then, if I do not boot debian, but shutdown before debian starts, I can wakeonlan successfully again.
If I boot debian and then shutdown, game over: wakeonlan nolonger works.
$ ethtool eth0 | grep -i wake
Supports Wake-on: g
Wake-on: g
A bit of research found the suggestion:
$ lspci -tv | grep -i ether
+-1c.2-[02]----00.0 Broadcom Corporation NetLink BCM57788 Gigabit Ethernet PCIe
$ cat /proc/acpi/wakeup
Device S-state Status Sysfs node
P0P2 S4 *disabled
P0P3 S4 *disabled
[Code] ....
How to get wakeonlan working under Jessie with a Broadcom BCM57788?
I had my Canon DV camcorder working well with Kino for capture in Fedora 11. I upgraded to F12 recently and tried to capture some video tonight. It does not seem to even recognize my camera.My card: 02:08.0 FireWire (IEEE 1394): Agere Systems FW322/323 (rev 04)My kernel: 2.6.31.12-174.2.22.fc12.i686.PAEI read somewhere about installing ieee1394 kernel modules from ATRPMs and rebuilding the kernel but
View 1 Replies View RelatedWell I guess the topic says it all. I've recently upgraded to Maverick from Lucid all went smoothly until i restarted and realized that the remote desktop server included stopped functioning all of a sudden. tried other vnc servers with no luck.
View 9 Replies View RelatedI reinstalled Ubuntu on my HP pc-40 computer. I used to run Hardy Heron and am now running Karmic Koala. The cd drive which had had issues for a while, broke after finishing the install, when I tried to get the cd out.I dont know if this has anything to do with it, or if my computer is too old for Karmic Koala, or if possibly the harddrive didn't appreciate being overwritten a second time - but the graphics are not working well (small squares of previous windows linger in my present browser window*)everythin is much slower, and many applications come up without a border, or their windows cant be moved with the mouse.
To top it off, while I tried to fix a bug with the terminal (no border) and uninstalled it, I couldnt install it back. So no terminal, which really makes even a newbie like me sad.If I cant solve it in a few days I will probably try to install a smaller distro via USB - I think Slax can be installed straight to USB without a live cd?
The title pretty much says it all, the sound on this system was working fine until I ran the upgrade to Lucid. I've tried everything in the standard troubleshooting guide, the sticky threads and plenty of forum searches but so far I've come up with nada. For some reason Ubuntu refuses to see my soundcard, no matter how much I twist and tweak it. It's an Asus M3A78 motherboard with an on-board Realtek ALC1200 chip (snd-hda-intel). Here's most of the relevant output, hopefully someone can easily spot what's going on because I'm getting snow-blind staring at the monitor. code...
View 4 Replies View RelatedI have a Broadcom wireless card in my hp dv6500z laptop, I had it all working properly in FC9 thanks to bbfuller and his post on the subject. After I upgraded to FC11 I have been unable to get it to connect.
I can see my neighbor's sites and suppose I could see my own if the SSID was allowed to broadcast but I keep that turned off. I put in all of the setting, including the network security key, but it won't connect, then when I go back and look again, the security key is not even close to what I put in; it gets changed to a huge string of characters.
I redownloaded broadcom-wl-4.150.10.5.tar.bz2.tar and followed the instruction on the post once again but no luck, which, after I thought about it, was a waste of time because if I can see other's wireless, then the card must be working. I have tried using Network Manager and not using Network Manager and still no luck...