I just bought a new 24inch monitor that supports the resolution 1920x1200. Unfortunately, the nvidia-settings dialog does not have this resolution as an option (currently running on 1920x1080). The graphics card is Geforce 6200 (should support the wanted resolution), and the monitor is connected with the VGA cable (if that matters).
View 7 Repliesin my media pc i have a geforce 8400, attached to a 32" 720p lcd using a dvi to vga adapter, and it is miss detecting the resolution it detects the resolution as 1080p, so when i try to enable full gpu scaling it gets the resolution wrong resulting no image on the screen. how do i manualy set the "back end resolution"
View 6 Replies View RelatedI have the same problem where i cant switch to my 1920x1200 anymore it says 1600x1200 is the highest which sucks because i have no idea why or how it switched back to 1600x1200 when i had 1920x1200.
View 1 Replies View RelatedI recently installed Ubuntu, 10.4
My problem is that when i log in, the resolution isnt what i want. So i change it via the Nvidia x server settings, and press Save to x config file
Yet when i log in again, it defaults back to what it was before i changed it?
Iv looked all over the internet for the past 2 days and nothing seems to work.
After installing some (much needed) upgrades, I am stuck being unable to install nvidia-settings after screen-resolution-extra upgraded from .11 to .13. Nvidia-settings, supposedly, requires .11. I can, of course, downgrade to .11, but I do not know if this is recommended. Is there anyway to get nvidia-settings back without downgrading? What is a good course of action?
View 1 Replies View Relatedi'm having a problem with nvidia-settings is that my resolution is not listed in. the only resolutions available are 640x480 and 320x240, the "detect display" doesn't work either.by the way i'm using the driver from nvidia site.other point is that i couldn't change resolution on kde before i installed the nvidia driver, it just showed the same two resolutions, i thought it was because i hadn't install the nvidia drivers but i got the same problem.
View 4 Replies View RelatedI've been using Ubuntu on and off for the past few years, however since the release of Ubuntu 10.04 I have decided to dedicate my Dell laptop to Ubuntu. Everything is up and running smoothly with one exception: my screen resolution. My graphics card is an NVidia Geforce Go 7300, and as such I am using the "NVidia accelerated graphics driver (version current)." Compiz is working properly and the only issue I'm having with this setup is that my screen resolution is way too large for me to be able to see it. The screen is a 15.4 inch and the native resolution of 1680x1050 is exceptionally difficult to read. In the NVidia settings I am looking for a resolution of 1280x800, a resolution which I have used before on this laptop in a different operating system, however the closest I can come without stretching the image is 1440x900. I have searched both this forum and google religiously in search of an answer to this problem - not just today, but many times in the past; once for each version of Ubuntu that was released. Each attempt mutilating the xorg.conf file in a different manner, yet all to no avail. I have spent a woeful amount of my life trying to fix this issue, however I have succumb to failure and futility each time. I am willing to try a vast number of things that I have not already attempted in order to fix this, as well as a few tried methods that I may have executed incorrectly; as I would like to have a readable screen with which to use my laptop. Below is the contents of my laptop's current xorg.conf file.
Code:
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildd@palmer) Fri Apr 9 10:35:18 UTC 2010
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
[Code]...
Just got an HP dv6-2150 laptop. Dual boot with Windows 7 and 9.04 (9.10 will not work but that's a different story). The screen resolution is too low and is set at the highest option available (1024x768 which is a 4:3 aspect ratio). The HP uses the new Intel i3-330m chipset with on-board Intel HD graphics. The system is capable of 1366x768 resolution (16:9) - so how do I get it there? xorg.conf looks real generic - nothing specific to Intel.
View 7 Replies View RelatedI'm running dual-screen. On 24" at 1920x1080 and one 19" at 1440x900. After installing Mint 9 I can't set the resolution any higher than 640x480 in nvidia-settings. I've installed the "recommended" nvidia-driver that Mint suggests.
[Code]...
What could be the problem? Why can't I set the res higher than 640 in nvidia-settings? Everything worked in Mint 8 (10.04). During installation the res was higher than 640.
I'm using Ubuntu 9.10 64-bit with a GTS 250. After installing the restricted driver from NVIDIA's website I get stuck at a 640x320 resolution. The only other option I get is 320x240. The resolution I need is 1680x1050.
I've also encountered this problem with a 9600GT.
I have 2 monitors, a 22 inch samsung as my main and an acer as my alt. I am trying to get the samsung monitor to display, but is is disabled. So I enable it as a separate x display, then save, but when I restart x, the settings didn't save. I save the config under under /etc/X11/xorg.conf. What am I doing wrong?
View 4 Replies View RelatedI'm a relatively new Debian user, having come from Ubuntu. I recently bought a Dell micro-server to function as my Kodi media player. I installed an nVidia GeForce 210 to output to my Pioneer home theatre amplifier. The amp takes all my inputs (eg. Satellite set-top decoder, PS3, Kodi etc) and outputs to the TV. I installed XFCE as my desktop environment so that I could still interact with it via VNC.
Everything is working great except for one exceptionally annoying problem! Every day, I find that I am having to VNC into the desktop, load up nVidia X Settings, and change my screen resolution from Auto to 1920x1080 because it has lost the display configuration and the screen is blank. I presume this happens when the amplifier switches from one input to the next. It doesn't matter if I save the configuration to my X11.conf file or not - it still resets itself.
Before, this setup would run for months without any intervention (Same amplifier + HP microserver + Ubuntu + LXDE + ATI video card), so I'm pretty confident that the issue is either Debian, XFCE, or the nVidia card.
I have connected my computer to my LCD-TV (HDMI-cable) to enjoy my movies and such, on a big screen. I have nVidia GeForce 7050 so in nvidia-settings I've been using the TwinView configuration which allows me to see both the monitor and the TV.
There was a bit of trouble-shooting but it worked just fine until yesterday when I changed my monitor to a new one and on the way probably messed up in nvidia-settings. I thought it would be easy to fix it but the configuration (in nvidia-settings) is stuck on "separete x-screen" and doesn't allow any changes at all. When I hit the "Detect display" nothing happens although I have the TV connected!
Maybe my xorg.config could tell somebody what is wrong. I've been messing around with the file and made lots of changes acc to different advices but I really don't understand the options and settings so I'm afraid I'll soon do something inreperable.
[Code]...
Yesterday I played a little with a Bitcoin miner and discovered today that I must have scambled my 3D settings. My Intel graphics card doesn't seem to work, instead I must have added a nVidia Settings Manager to my menu.
I already removed the package I mistakenly installed (something concerning OpenCL) but nothing happens. The xorg.conf file seems to be okay.
Gnome now only starts in 2D mode and Unity refuses to work at all. how I might get my Intel card back working?
Since I upgraded to 9.04 a while back I have had this annoying screen resolution issue. Every time I log into my Ubuntu system the screen resolution defaults to 1280x1024. My preferred desktop resolution is normally set at 1680x1050. So each time I log in I have to open the Nvidia control panel and manually set the screen resolution to 1680x1050. Even after logging out it will still go right back to 1280x1024 when I log back in.
But the funny this is I am almost positive the login screen resolution is 1680x1050 because the picture is crisp unlike the blurry and distorted picture at 1028x1024. I have tried everything from manually editing the x.org conf file to running the Nvidia control panel as root. Nothing saves my preferred resolution of 1680x1050. My Nvidia driver is version 190.42 and Ubuntu version is 9.04. The monitor is an ASUS VW192T+ which is detected by the Nvidia driver.
Ubuntu 10.04, nVidia GeForce 9400, driver ver 195.36.15.When I log in, the system always comes up in 800x600 mode. I went into the NVIDIA X Server Settings page and changed it to my preferred setting of 1152x864. I hit Apply, then Save to X Configuration File (with correct root password).All is well until restarting. Then it reverts back. The update doesn't stick. How can I make this the permenant setting?
View 3 Replies View RelatedI'm a first timer on Ubuntu and I have a little problem with my Nvidia graphic card. After lots of attempts I can't get the 1280x1024 resolution that both of my monitors have. Instead I'm running on 1024x768.Is this a way to fix it?
View 8 Replies View RelatedRecently I encountered a problem with a triple-monitor setup where the EDID was rejected by the nvidia driver (version 195.36.0, claiming that the EDID checksum was invalid. The maximum resolution that the driver would allow was 640x480. Searching through the X logs (/var/log/Xorg.0.log), I found the following message:
Code:
(WW) Jul 26 21:37:57 NVIDIA(GPU-0): The EDID read for display device DFP-0 is invalid: the
(WW) Jul 26 21:37:57 NVIDIA(GPU-0): checksum for EDID version 1 extension is invalid.
[Code].....
Running Ubuntu 10.04 with an Acer wide monitor, 1600x900. The graphics card is a Gefoce 6200. When I run nvidia-settings I can select 1600-900 and it looks fine. I can "Save to X configuration file" and get no errors. However if I log out and back in, the resolution changes to 1360x768 which causes the tool bar at the top to be mostly somewhere to the left of and above the monitor. It makes life rather difficult when you can't get to the Applications and Places menus. I also tried nvidia-configure but it created essentially the same xorg.conf file.
This is the xorg.conf file generated:
Quote:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder75) Sun Nov 8 21:50:38 PST 2009
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildd@palmer) Fri Apr 9 10:35:18 UTC 2010
[Code]....
1600x900 is the native mode of this monitor so the driver shouldn't be getting any errors if it trys to set that resolution.
I have a Dell E6500 laptop (1280x800 screen), which I frequently dock.The dock as two Dell 1908FP 20" monitors connected by DVI. I can move between the laptop display and the twins by manually changing display configuration in NVIDIA X Server settings, but this is a pain requiring about 15 clicks each time.
I have tried using the "Save to X Configuration File" option in the Nvidia server settings, but this seems to screw everything up. I need to dynamically change between the setups... anyone have advice on getting that done?Can the xorg.conf file be configured to do it?My xorg.conf looks like this:
Section "Screen"
Identifier"Default Screen"
DefaultDepth24[code]......
I had Ubuntu 10.04 running fine. Then I got curious about NVIDIA XServer.
"ATI Technologies Inc RV380 [Radeon X600 (PCIE)]" - Video Card
I opened it up, clicked a settings change, and said OK.
It said you need to update your blah blah blah.
Then it said blah blah blah doesn't exist.
Then it said it would create it for me.
Then I said REBOOT!
Now I get a black screen of death.
The only way I can get anything to happen on my monitor that comes from this computer is to boot into the Install Disk and say "TRY UBUNTU".
I know there are a lot of threads out there for same or similar issues, but nothing I found was working for me until, by sheer chance, I found this very simple solution on the Fedora forums. Too elegant not to share.Environment:Ubuntu 10.10nVidia GeForce 5500Samsung SyncMaster 225BWUsing DVI cable (in case it matters)Issue:After installing the proprietary nVidia drivers, the screen resolution was no longer the correct native resolution of the display. In my case specifically, the nVidia X Server Settings utility was detecting the maximum supported screen resolution was 1280x1024 while my display's native resolution is 1680x1050.Solution:Open a Terminal window.Make a backup copy of the original xorg.conf file. This is just good form any time you are making config file customizations.
Code:
sudo cp -p /etc/X11/xorg.conf /etc/X11/xorg.conf_backup
Open 'xorg.conf' in a text editor.
[code]....
My screen displays everything in a very wide but also very short way. When i click on (X Server Display Configuration) NVIDIA X Server Settings
I get this:
Having been using squeeze on my primary system for some time, I decided to install it on my media center PC. After doing a clean install I lost sound (another post) and my maximum video resolution dropped to 1280x1024. I was previously getting 1920x1080 (native) resolution under lenny on this box. So it's a mystery to me why I'm not getting that now. As you can see, the nvidia module is loaded:
# lsmod | grep nvidia
nvidia 9821382 0
i2c_core 12570 2 i2c_piix4,nvidia
PS--This was installed the "debian way" via module assistant.
I run Ubuntu 9.04 on with proprietary NVidia driver 180.44.When I change anything in the nvidia-settings, e.g. screen resolution, brightness, second screen etc, everything works fine - except for the fact that I can't play any video files in any player. Sound is there, players don't display any error messages, but the image is black. Flash video within browsers is fine, though.Things go back to normal with the new settings kept after restarting X. However, having to restart X and lose my desktop set up every time when I just want to connect my laptop to my office screen is highly inconvenient.Is this a bug or expected behaviour that I have to live with?
View 3 Replies View RelatedI am stuck at 1024x768 in Ubuntu 10.04 with the nVidia GeForce 7100. I installed the drivers suggested by nVidia on their website, but it doesn't seem to heighten my resolution any. 1024x768 is the highest which appears in nVidia X Server Settings.
Xorg.conf:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 256.53 (buildmeister@builder101) Fri Aug 27 21:34:01 PDT 2010
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen" 0 0
InputDevice "Configured Keyboard" "CoreKeyboard"
[Code]...
Is there a way to fix this without having to buy a new card? I've read that the GeForce 7100 is pretty crappy, but I've got no money to space at the moment.
I recently purchased a cheap computer to use for everyday tasks. It came pre-loaded with Windows 7. The monitor I am using is a Vizio VX20L. It's native resolution is 1366X768. I have no problem with the screen resolution in Windows 7 but in Ubuntu, I am having some issues. I have the propriatary Nvidia driver installed in Ubuntu but for some reason I cannot get the screen resolution right. I am currently using a resolution of 1360x768 and the right part of my desktop is not on the screen.
I have tried to adjust the screen size using the monitor settings, but I still cannot get the whole screen to show up. If I set the resolution to Auto in the NVIDIA X Server Settings, it defaults to 1280X1024 and I can see my whole desktop, but it is streeeeetched. Here is some relevant information pertaining to my system:
I'm using Ubuntu 10.04
Integrated Video chip is NVIDIA GeForce 6150SE
The driver I'm using is NVIDIA accelerated graphic driver (version current)[Recommended]
screen is a Vizio VX20LHD
I had some issues with nvidia drivers, and removed all of the packages using
Code: Select allrm /etc/X11/xorg.conf and Code: Select allapt-get purge nvidia*
Upon reboot, I was back with nouveau drivers and proceeded to reinstall nvidia drivers according to [URL] .....
Code: Select allapt-get install nvidia-driver
apt-get install nvidia-xconfig
I can then change my refresh rate using
Code: Select allnvidia-settings
but when I hit "Save to X configuration file", I get the following output in terminal:
Code: Select allroot@debian:/home/anon# nvidia-settings
Package xorg-server was not found in the pkg-config search path.
Perhaps you should add the directory containing `xorg-server.pc'
to the PKG_CONFIG_PATH environment variable
No package 'xorg-server' found
As a result, my nvidia preferences aren't saved across reboot.
Here are all of my sources:
Code: Select alldeb [arch=amd64,i386] http://repo.steampowered.com/steam/ precise steam
deb-src [arch=amd64,i386] http://repo.steampowered.com/steam/ precise steam
deb http://ftp.ca.debian.org/debian/ jessie non-free contrib main
deb-src http://ftp.ca.debian.org/debian/ jessie non-free contrib main
[Code] ....
System Specs:
Debian GNU/Linux 8 (jessie) 64-bit
Gnome Version 3.14.1
Processor: Intel® Core™ i7-4770K CPU @ 3.50GHz × 8
Graphics: GeForce GTX 780/PCIe/SSE2
Unable to get high res, colour or 3-D acceleration working with 8.04 Hardy. Not a hardware problem as it works perfectly in dual-boot XP.
[Code]...
I am using Fedora 13 x86_64 on a Acer Aspire 7730ZG laptop with: 01:00.0 VGA compatible controller: nVidia Corporation G98 [GeForce 9300M GS] (rev a1) I have kmod-nvidia-2.6.33.6-147.2.4.fc13.x86_64-195.36.31-1.fc13.2.x86_64 installed from rpmfuison when I plug in the hdmi cable to the tv, my tv says the resoultion is at 720p, and I can not get any of the resolutions settings to look right on seperate x screen with the nvidia X server settings gui. my tv is a vizo 42inch. also another question is their a way to set the video card to output at 1080? this might be part of my problem?
View 14 Replies View Related