Ubuntu Multimedia :: Changing Display Configuration In NVIDIA X Server Settings?
Feb 23, 2010
I have a Dell E6500 laptop (1280x800 screen), which I frequently dock.The dock as two Dell 1908FP 20" monitors connected by DVI. I can move between the laptop display and the twins by manually changing display configuration in NVIDIA X Server settings, but this is a pain requiring about 15 clicks each time.
I have tried using the "Save to X Configuration File" option in the Nvidia server settings, but this seems to screw everything up. I need to dynamically change between the setups... anyone have advice on getting that done?Can the xorg.conf file be configured to do it?My xorg.conf looks like this:
Section "Screen"
Identifier"Default Screen"
DefaultDepth24[code]......
View 5 Replies
ADVERTISEMENT
Jan 31, 2011
I have 2 monitors, a 22 inch samsung as my main and an acer as my alt. I am trying to get the samsung monitor to display, but is is disabled. So I enable it as a separate x display, then save, but when I restart x, the settings didn't save. I save the config under under /etc/X11/xorg.conf. What am I doing wrong?
View 4 Replies
View Related
Jan 4, 2010
Is it possible to have gnome's display settings recognise higher refresh rates than 56hz, as my nvidia is set to 85hz, but gnome display still thinks its 56hz, and I believe this is causing many programs I'm using to refresh at 56hz. Compiz works beautifully after overriding the refresh rate inside it, as it too thought I was using 56hz instead of 85 but many games aswell as CairoDock as jerky, which makes me think it is a refresh issue.
How can I make gnome know I'm using 85hz?
View 5 Replies
View Related
Aug 21, 2010
I am using Fedora 13 x86_64 on a Acer Aspire 7730ZG laptop with: 01:00.0 VGA compatible controller: nVidia Corporation G98 [GeForce 9300M GS] (rev a1) I have kmod-nvidia-2.6.33.6-147.2.4.fc13.x86_64-195.36.31-1.fc13.2.x86_64 installed from rpmfuison when I plug in the hdmi cable to the tv, my tv says the resoultion is at 720p, and I can not get any of the resolutions settings to look right on seperate x screen with the nvidia X server settings gui. my tv is a vizo 42inch. also another question is their a way to set the video card to output at 1080? this might be part of my problem?
View 14 Replies
View Related
Mar 9, 2010
I installed the nvidia proprietary drivers with click-install and everything perfect, I have desktop effects working but the problem is that when you open the config. screen settings to make sure everything was really good, I get to screen unknown April.
The maximum resolution is the correct 1440 * 900 for 19 "but the refresh rate by not recognizing the monitor down to 50hz me and gives me the option to 60hz as it was before installing the nvidia drivers.
How can I fix the display settings?
View 6 Replies
View Related
Sep 16, 2010
In nvidia-settings I see, alongwith Disabled and TwinView settings, "Separate X Server". I tried choosing the option for my LCD (connected via HDMI), but I get a blank screen, presumably since the LCD's X server has nothing to render.
How do I direct any application (say vlc) to use that X Server instead of the Monitor's X server?
View 1 Replies
View Related
Sep 18, 2015
I have a Dell 1505E with Debian 3.16.7 which is unable to connect to channels 12 and 13 even after changing wifi regional settings to different countries (using iw reg set).12 and 13 are legal to use in the UK. What should I do?
Code: Select allsudo lspci | grep -i wireless
02:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01)
Code: Select alllspci -vv -s 02:00.0
02:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01)
Subsystem: AzureWave Device 2047
[code]....
View 0 Replies
View Related
Sep 18, 2010
On a Dell 14n, 10.04. Mic problem: To use the mic jack/external mic, I need to have MIC 3 selected at SYSTEM/PREFERENCES/SOUND/INPUT To use the built in mic, I need to have MIC 1 selected
How can I get these mic's to work w/o having to change the settings each time I want to switch mic's.. so that if the mic jack is plugged in, then the external mic works. and if the mic jack is unplugged, then the built in mic works.
View 9 Replies
View Related
Aug 30, 2015
I've always used Debian with a single monitor and no need of proprietary drivers, because I usually don't do graphics or multimedia. Now I'm asked to set-up a machine with 3 nvidia video cards (770) and 4 monitors and everything went south. I started with just 2 monitors connected to 2 different video cards, not wanting to push my luck.
I installed a fresh Jessie and followed the instruction to install the nvidia drivers and tools from the Wiki. Everything went smooth. After reboot I executed (as root) nvidia-settings and I configured the two monitors to be one to the right to the other, with BaseMosaic option (at this point just one monitor was active) I saved the configuration to /etc/X11/xorg.conf , I even executed nvidia-xconfig as suggested, I rebooted and nothing happened, only one monitor was working, while the other -- looking again in the nvidia settings -- was still disabled.
I then tried with xinerama option and things are even worse, since now both monitors are black. I can login in one textual shell, but then I don't know what to do, since in my 10+ years of linux ... I never had to mess with X server. Is there a way to at least recover a working X without reinstalling everything?
View 0 Replies
View Related
Apr 8, 2011
Still pretty new to this, from what i have read, the more info i give the better, I am running ubuntu 11.04 with KDE installed via the terminal. I was trying to get my TV to work as another display, I don't know what I have done, after my earlier problems I have learnt to back up and restore my xorg.conf file but with no luck, I now can't change any settings as the title says the apply button is grayed out and when i try and save it to the xorg.conf file and restart the xserver it says that "Your current changes to the X server display configuration may no longer be applied due to changes made to the running X server.
You may either reload the current X server settings and lose any configuration setup in this page, or select "Cancel" and save your changes to the X configuration file (requires restarting X to take effect.)
If you select "Cancel", you will only be allowed to apply settings once you have reset the configuration.Your current changes to the X server display configuration may no longer be applied due to changes made to the running X server. You may either reload the current X server settings and lose any configuration setup in this page, or select "Cancel" and save your changes to the X configuration file (requires restarting X to take effect.)
If you select "Cancel", you will only be allowed to apply settings once you have reset the configuration. Your current changes to the X server display configuration may no longer be applied due to changes made to the running X server. You may either reload the current X server settings and lose any configuration setup in this page, or select "Cancel" and save your changes to the X configuration file (requires restarting X to take effect.)
If you select "Cancel", you will only be allowed to apply settings once you have reset the configuration."
when I booted last i got terminal with this showing, for the first time,
Xlib: extension "RANDR" missing on display ":0".
(orca:1984): Wnck-WARNING **: Property _NET_WM_NAME contained invalid UTF-8
My xorg.conf is
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 270.29 (buildd@roseapple) Fri Feb 25 14:43:24 UTC 2011
Section "ServerLayout"
[Code]...
View 5 Replies
View Related
Jan 26, 2010
Just got an HP dv6-2150 laptop. Dual boot with Windows 7 and 9.04 (9.10 will not work but that's a different story). The screen resolution is too low and is set at the highest option available (1024x768 which is a 4:3 aspect ratio). The HP uses the new Intel i3-330m chipset with on-board Intel HD graphics. The system is capable of 1366x768 resolution (16:9) - so how do I get it there? xorg.conf looks real generic - nothing specific to Intel.
View 7 Replies
View Related
Jul 31, 2011
I'd like to do something, but I don't seem to find the solution. Here is my problem: I have a laptop and I plugged in another monitor to it. What I want to do is when UserA logs in, both of the monitor is used, but when UserB logs in, only one of the monitor is used. When I change the display settings it applies to the other user too. I'd like to have different display settings for each user
View 7 Replies
View Related
Jun 12, 2010
I'm still working on ubuntu 9.10 with an acer aspire 1810tz. To use my microphone I found out that I have to change my microphone settings because it's mono and the default setting is thinking it's stereo: With the Volume Controller I setup one chancel to 5 and the other to 90 and the mic is working fine. Starting Skype and using it I see that the setting is reducing the volume for the mic below 20, so nobody can hear me. I tried closing first Volume Controller and then starting Skype, no matter the volume of the mic is reduced. How do I stop this behavior?
View 2 Replies
View Related
May 17, 2010
Using squeeze with a GeForce4 MX 440 video card (NVIDIA) I have a monitor (4/3 aspect ratio, 1024x768 usually), and a TV connected via S-video After installing the NVIDIA driver using the NVIDIA binaries I managed to have a cloned twin screen configuration working.
However, the monitor is (wrongly) detected as having size 1824x768 (aspect ratio is widescreen) Using system monitor, I can set the correct size, but only for one session; besides, the login screen too is messed up the xorg.conf file seems right: proper resolution modes are set; xorg.0.log too
View 2 Replies
View Related
Jun 30, 2010
I'm running dual-screen. On 24" at 1920x1080 and one 19" at 1440x900. After installing Mint 9 I can't set the resolution any higher than 640x480 in nvidia-settings. I've installed the "recommended" nvidia-driver that Mint suggests.
[Code]...
What could be the problem? Why can't I set the res higher than 640 in nvidia-settings? Everything worked in Mint 8 (10.04). During installation the res was higher than 640.
View 4 Replies
View Related
Jan 9, 2010
My display settings seem to have been corrupted after I upgraded from 9.04 to 9.10. I can only view my screen in 1280 x 1024 - no other resolutions work. Ubuntu is also not detecting my monitor, a Dell E193FP (19"). In reading some other posts, I see that the first question will be to post my xorg file, which follows.
View 1 Replies
View Related
Jul 19, 2010
How do I do this? You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server.
View 3 Replies
View Related
Jan 13, 2011
I plugged the usual 4-pin s-video cable into my TV and graphics card. I went to nvidia x server settings, nothing. I hit detect monitors, nothing. I changed the TV to the proper input channel, Nothing. It's a bit annoying,I used it with the old GeForce Ti4200.
View 1 Replies
View Related
Feb 5, 2011
I just bought a new 24inch monitor that supports the resolution 1920x1200. Unfortunately, the nvidia-settings dialog does not have this resolution as an option (currently running on 1920x1080). The graphics card is Geforce 6200 (should support the wanted resolution), and the monitor is connected with the VGA cable (if that matters).
View 7 Replies
View Related
Apr 23, 2011
we're running an Ubuntu 10.04 LTS network on our company, authenticating against an Openldap/heimdal-kerberos server.Previously, the clients were authenticating against a Windows 2003 Domain without any problems.After modifying the krb.conf, ldap.conf, nsswitch.conf and nscd.conf files to authenticate the machines against the openldap/heimdal setup, we started experiencing strange problems.
One issue is, for example, the polkit-agent-gnome not starting. This component integrates policykit into gnome. It looks like the agent is unable to start due to some kind of delay with DBUS. Starting the agent manually keeps giving errors until about 70 seconds after login, when the agent can be started without problems. During the delay it is also impossible, for instance, to open the "shut down" menu on the top right of gnome. You can click on the menu, but nothing appears.Trying to start the polkit-agent manually gives these errors (I'll be attaching detailed errors when at work!):
Code:
DBus error org.freedesktop.DBus.Error.NoReply: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken
GLIB ERROR ** default - Not enough memory to set up DBusConnection for use with GLib It really looks like DBus or something related to it is starting "too late" but I can't seem to find the reason. I'm pretty sure this has to do with some timings or whatever in the krb/ldap config files...
View 3 Replies
View Related
Feb 14, 2010
I have connected my computer to my LCD-TV (HDMI-cable) to enjoy my movies and such, on a big screen. I have nVidia GeForce 7050 so in nvidia-settings I've been using the TwinView configuration which allows me to see both the monitor and the TV.
There was a bit of trouble-shooting but it worked just fine until yesterday when I changed my monitor to a new one and on the way probably messed up in nvidia-settings. I thought it would be easy to fix it but the configuration (in nvidia-settings) is stuck on "separete x-screen" and doesn't allow any changes at all. When I hit the "Detect display" nothing happens although I have the TV connected!
Maybe my xorg.config could tell somebody what is wrong. I've been messing around with the file and made lots of changes acc to different advices but I really don't understand the options and settings so I'm afraid I'll soon do something inreperable.
[Code]...
View 5 Replies
View Related
Jun 19, 2011
Yesterday I played a little with a Bitcoin miner and discovered today that I must have scambled my 3D settings. My Intel graphics card doesn't seem to work, instead I must have added a nVidia Settings Manager to my menu.
I already removed the package I mistakenly installed (something concerning OpenCL) but nothing happens. The xorg.conf file seems to be okay.
Gnome now only starts in 2D mode and Unity refuses to work at all. how I might get my Intel card back working?
View 1 Replies
View Related
Dec 9, 2010
I searched the forums for a long time and could not found any relevant informationI am new to ubuntu (10.10 64bit) and I just want to know if it is possible, like it is in win7 (sorry!), if I can plug in my hdmi cord and have the laptop speakers and display disable, and have the external display and its spears enabled.
View 2 Replies
View Related
Sep 1, 2011
is everytime i reboot , my keyboard is reset to USA. im in canada & it pisses me off each time i need to change it also.all my options on EMESENE is the same issue always RESET.it's like if nothing keeps the changes once rebooted.
View 1 Replies
View Related
Jan 21, 2010
in my media pc i have a geforce 8400, attached to a 32" 720p lcd using a dvi to vga adapter, and it is miss detecting the resolution it detects the resolution as 1080p, so when i try to enable full gpu scaling it gets the resolution wrong resulting no image on the screen. how do i manualy set the "back end resolution"
View 6 Replies
View Related
Dec 11, 2010
I had Ubuntu 10.04 running fine. Then I got curious about NVIDIA XServer.
"ATI Technologies Inc RV380 [Radeon X600 (PCIE)]" - Video Card
I opened it up, clicked a settings change, and said OK.
It said you need to update your blah blah blah.
Then it said blah blah blah doesn't exist.
Then it said it would create it for me.
Then I said REBOOT!
Now I get a black screen of death.
The only way I can get anything to happen on my monitor that comes from this computer is to boot into the Install Disk and say "TRY UBUNTU".
View 6 Replies
View Related
Jan 5, 2010
I am new to Ubuntu (Karmic with GNOME). I have a Samsung LED UEB7020, with an Asrock ION 330 BD player feeding to a Onkyo TXSR607, AV rec. The other day I downloaded NVidia v180.25, which was very useful, because it immediately solved an earlier teething problem of no sound. However immediately upon re-booting and ever since, the screen size is too big for the TV, meaning that I can not see the top, bottom, side and left of the display by about 2 inches either way. I have checked the NVidia resolution settings and they are correct for the TV, ie 1920 by 1080.
My etc/X11/ xorg.conf file reads as follows:
Section "Screen"
Identifier "Default Screen"
DefaultDepth 24
EndSection
Section "Module"
Load "glx"
EndSection
Section "Device"
Identifier "Default Device"
Driver "nvidia"
Option "NoLogo" "True"
EndSection
View 9 Replies
View Related
Sep 1, 2010
I have ubuntu 10.4 32 bit. I have 2x gtx 285's in sli that work perfectly fine in sli in windows (so its not a hardware not properly physically installed issue). But in ubuntu in the x server settings only one of the cards shows up. I was wondering if this is a 32 bit issue as in the past running 64 bit they have both shown up fine.
View 6 Replies
View Related
Mar 8, 2011
My screen displays everything in a very wide but also very short way. When i click on (X Server Display Configuration) NVIDIA X Server Settings
I get this:
View 1 Replies
View Related
Apr 16, 2010
I run Ubuntu 9.04 on with proprietary NVidia driver 180.44.When I change anything in the nvidia-settings, e.g. screen resolution, brightness, second screen etc, everything works fine - except for the fact that I can't play any video files in any player. Sound is there, players don't display any error messages, but the image is black. Flash video within browsers is fine, though.Things go back to normal with the new settings kept after restarting X. However, having to restart X and lose my desktop set up every time when I just want to connect my laptop to my office screen is highly inconvenient.Is this a bug or expected behaviour that I have to live with?
View 3 Replies
View Related
