I'm a first timer on Ubuntu and I have a little problem with my Nvidia graphic card. After lots of attempts I can't get the 1280x1024 resolution that both of my monitors have. Instead I'm running on 1024x768.Is this a way to fix it?
View 8 Replies
I need to set my resolution to 1280x1024. Problem is, that the NVIDIA X Server Settings does not display such a resolution and I want to use that! My monitor is an LCD capable of upto 1280x1024 75HZ resolution. I'm using Ubuntu 10.10. I did the xrandr command to check what resolutions are available and its output was:
Failed to get size of gamma for output default
Screen 0: minimum 320 x 240, current 1024 x 768, maximum 1024 x 768
default connected 1024x768+0+0 0mm x 0mm
1024x768 50.0 60.0*
800x600 51.0 52.0 53.0
680x384 54.0 55.0
640x480 56.0
512x384 57.0
400x300 58.0
320x240 59.0
In NVIDIA X Server Settings, the list of available resolutions are:
(all of the above)
1152x864
1360x768
I have NVIDIA GeForce 9500GT.
I have Ubuntu 10.04 32bit installed on my desktop. My video card is an nVidia 7800 GT. My Monitor is a Sceptre X24WG. I am able to use the NVIDIA X Server Settings utility to change my resolution to 1920x1080 as well as 1920x1200,and 3d opengl accelerated games work. When i reboot, the x server comes up with 1280x1024 as the resolution. I want it to remember the resolution i selected instead of defaulting to a different resolution.
I was running Kubuntu 8.10 previously and had some difficulty setting up the graphics initially, but i don't recall what steps i had taken to get it to work. When i recently reformatted to install Ubuntu 10.04, it wouldn't go directly to 10.04. The screen would go to a garbled display and would load the install window, so i installed 9.04 and then upgraded to 9.10 and then 10.04, without trouble.
I'm using the nVidia hardware driver version 195.36.15, which in the hardware drivers utility is listed as the current and recommended version. It originally wouldn't install until after i had rebooted into the 2.6.31-21 kernel. I have tried the option to save to x configuration file. When i save to x configuration file, the xorg.conf in /etc/X11/ looks like this:
Code:
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildd@palmer) Fri Apr 9 10:35:18 UTC 2010
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder75) Fri Mar 12 01:42:27 PST 2010
# xorg.conf (X.Org X Window System server configuration file)
[Code]...
I'm running 10.10. I have a Nvidia GTX 460. My actual resolution is only 1024x768. I can't get the native resolution (1280x1024). Nvidia-settings does not show this resolution. Google hasn't helped at all so far, and I have installed the Nvidia Driver.
View 2 Replies View RelatedWhen I boot my computer I get this message: Warning Pc video resolution is out of range Change setting to recommended resolution 1280x1024 @60mh So I hit ctrl alt f1 I typed in Sudo dpkg-reconfigure xserver-xorg Nothing happens. It's been very frustrating because with everything that I've looked up it says that it's suppose to guide me through something. I desperately need my computer for school.
View 8 Replies View RelatedFirst the Hardware:
- Celeron 500mhz with 256megs or RAM
- S3Virge DX Card with 4megs of RAM in a PCI slot
- Envision EN9410e LCD with native resolution of 1280x1024
- Sidux distro running (Debian Sid)
Things I have tried:
1. Without any post install configuration: GDM and XFCE booted up with an 800x600 screen size. Looks great, but size is too small would like the native resolution of 1280x1024.
2. Created a xorg.conf file with the command "Xorg -configure". First added the horizSync rates and the VertRefresh rates. File had "s3virge" as the driver listed for the card. Screen section I added under 16 depth and 24 depth the Modes "1280x1024". This results in GDM starting with colors all messed up in vertical lines and barely able to read the screen details. The resolution is correct, but the colors are completely messed up making it hard to read anything with vertical lines running through everything.
3. Changed the above xorg.conf file to use the "vesa" driver. GDM starts up in 1280x1024 and the colors look perfect, but when I log into XFCE it bombs out when the desktop appears and takes me back to the GDM log in page, never letting me run the XFCE desktop.
4. Ran an old Knoppix 5.1 CD and it configured a beautiful desktop with I believe a 1024x768 desktop and great colors. It looked like it was using the vesa driver when I looked at the XFree86 config file.
5. Ran ddcprobe and it identified the "vesa" driver with the S3virge DX card and showed the possible resolutions which included 1280x1024x32k and 1280x1024x64k. Once again leading me to believe that it should be possible to use this card with this monitor and use the monitor's native resolution of 1280x1024.
Any ideas what I could do to get this resolution or is it just impossible with this hardware? Do I have to settle with 800x600? #3 try boggles my mind because I can't figure out why GDM would look perfect but then it would bomb back to the GDM screen instead of starting XFCE.
Yesterday I installed ubuntu 10.04 LTS, it allow me only 800x600, 640x480 and 400x300 screen resolution, how can i set 1280x1024 ?
View 9 Replies View RelatedI just want my normal settings back. I deleted the original post because I really screwed something up and I have to use Windows until I can figure out how to fix it. Forget about my resolution preferences. My Linux boot is stuck in low-graphics mode
Would anyone be able to provide me step by step, easy to follow for a newb instructions on fixing my boot?
I have to use recovery mode to load any graphics at all, and it's stuck in low graphics mode and I can't change it. More info below.
I'm new to Ubuntu, just installed it today as my Windows 7 got corrupted and couldn't boot. So far it's great, but I have on issue. My monitor is unrecognized, and I can't go to 1280x1024 resolution at all. I only have these options:
640x480 4:3
848x480 16:9
800x600 4:3
1024x768 4:3
1360x768 16:9
I have an HP Compaq dx2200 I have a Viewsonic VA 702b Monitor Did all possible update, no help. Even tried to use the "additional drivers" option and none were shown.
I've installed Debian (Lenny) on my pc, with geForce 8500 GT, two monitor (LCD + CRT). i've correctly installed the driver i can enter in the nvidia's setup but:
1) the best resolution for my CRT (Sony Brillance 109P) is 640x480
2) video on LCD (LG Flatron L222WS) is no good bat I can setting different resolution
3) I can't save the XConfig cause i don't understand what permission I must have for writing on 'etc' folder
I am getting a screen resolution of 1280x1024 on my laptop, but I sometimes like the lower resolutions, which are unaccessible via the Screen Resolution program.
View 2 Replies View RelatedI have the nVidia GeForce 8500 GT 512MB graphics card, I put it in my system to get a speed boost and for a dual monitor setup, I don't have the proprietary drivers installed I tried installing them, and when I did it asked for reboot, so I did, and when it came back up only one monitor was in use, and it was running very very sluggish, so I opened up the Monitors from the settings and it said to use nVidia's thing, so when I did, I enabled the second monitor, and hit apply, and it asked for a restart of Xorg, doing that came back telling me that no monitors were find, and a reboot brings me straight to tty1... I tried both the recent version and the older one, both did the same thing, I really wanna get my Compiz effects back. is there a way to get this working? I will do anything you ask if it solves the problem...
View 2 Replies View RelatedI'm using Ubuntu 9.10 64-bit with a GTS 250. After installing the restricted driver from NVIDIA's website I get stuck at a 640x320 resolution. The only other option I get is 320x240. The resolution I need is 1680x1050.
I've also encountered this problem with a 9600GT.
I just bought a new 24inch monitor that supports the resolution 1920x1200. Unfortunately, the nvidia-settings dialog does not have this resolution as an option (currently running on 1920x1080). The graphics card is Geforce 6200 (should support the wanted resolution), and the monitor is connected with the VGA cable (if that matters).
View 7 Replies View RelatedSince I upgraded to 9.04 a while back I have had this annoying screen resolution issue. Every time I log into my Ubuntu system the screen resolution defaults to 1280x1024. My preferred desktop resolution is normally set at 1680x1050. So each time I log in I have to open the Nvidia control panel and manually set the screen resolution to 1680x1050. Even after logging out it will still go right back to 1280x1024 when I log back in.
But the funny this is I am almost positive the login screen resolution is 1680x1050 because the picture is crisp unlike the blurry and distorted picture at 1028x1024. I have tried everything from manually editing the x.org conf file to running the Nvidia control panel as root. Nothing saves my preferred resolution of 1680x1050. My Nvidia driver is version 190.42 and Ubuntu version is 9.04. The monitor is an ASUS VW192T+ which is detected by the Nvidia driver.
Ubuntu 10.04, nVidia GeForce 9400, driver ver 195.36.15.When I log in, the system always comes up in 800x600 mode. I went into the NVIDIA X Server Settings page and changed it to my preferred setting of 1152x864. I hit Apply, then Save to X Configuration File (with correct root password).All is well until restarting. Then it reverts back. The update doesn't stick. How can I make this the permenant setting?
View 3 Replies View RelatedRecently I encountered a problem with a triple-monitor setup where the EDID was rejected by the nvidia driver (version 195.36.0, claiming that the EDID checksum was invalid. The maximum resolution that the driver would allow was 640x480. Searching through the X logs (/var/log/Xorg.0.log), I found the following message:
Code:
(WW) Jul 26 21:37:57 NVIDIA(GPU-0): The EDID read for display device DFP-0 is invalid: the
(WW) Jul 26 21:37:57 NVIDIA(GPU-0): checksum for EDID version 1 extension is invalid.
[Code].....
Running Ubuntu 10.04 with an Acer wide monitor, 1600x900. The graphics card is a Gefoce 6200. When I run nvidia-settings I can select 1600-900 and it looks fine. I can "Save to X configuration file" and get no errors. However if I log out and back in, the resolution changes to 1360x768 which causes the tool bar at the top to be mostly somewhere to the left of and above the monitor. It makes life rather difficult when you can't get to the Applications and Places menus. I also tried nvidia-configure but it created essentially the same xorg.conf file.
This is the xorg.conf file generated:
Quote:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder75) Sun Nov 8 21:50:38 PST 2009
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildd@palmer) Fri Apr 9 10:35:18 UTC 2010
[Code]....
1600x900 is the native mode of this monitor so the driver shouldn't be getting any errors if it trys to set that resolution.
in my media pc i have a geforce 8400, attached to a 32" 720p lcd using a dvi to vga adapter, and it is miss detecting the resolution it detects the resolution as 1080p, so when i try to enable full gpu scaling it gets the resolution wrong resulting no image on the screen. how do i manualy set the "back end resolution"
View 6 Replies View RelatedI know there are a lot of threads out there for same or similar issues, but nothing I found was working for me until, by sheer chance, I found this very simple solution on the Fedora forums. Too elegant not to share.Environment:Ubuntu 10.10nVidia GeForce 5500Samsung SyncMaster 225BWUsing DVI cable (in case it matters)Issue:After installing the proprietary nVidia drivers, the screen resolution was no longer the correct native resolution of the display. In my case specifically, the nVidia X Server Settings utility was detecting the maximum supported screen resolution was 1280x1024 while my display's native resolution is 1680x1050.Solution:Open a Terminal window.Make a backup copy of the original xorg.conf file. This is just good form any time you are making config file customizations.
Code:
sudo cp -p /etc/X11/xorg.conf /etc/X11/xorg.conf_backup
Open 'xorg.conf' in a text editor.
[code]....
Having been using squeeze on my primary system for some time, I decided to install it on my media center PC. After doing a clean install I lost sound (another post) and my maximum video resolution dropped to 1280x1024. I was previously getting 1920x1080 (native) resolution under lenny on this box. So it's a mystery to me why I'm not getting that now. As you can see, the nvidia module is loaded:
# lsmod | grep nvidia
nvidia 9821382 0
i2c_core 12570 2 i2c_piix4,nvidia
PS--This was installed the "debian way" via module assistant.
I am stuck at 1024x768 in Ubuntu 10.04 with the nVidia GeForce 7100. I installed the drivers suggested by nVidia on their website, but it doesn't seem to heighten my resolution any. 1024x768 is the highest which appears in nVidia X Server Settings.
Xorg.conf:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 256.53 (buildmeister@builder101) Fri Aug 27 21:34:01 PDT 2010
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen" 0 0
InputDevice "Configured Keyboard" "CoreKeyboard"
[Code]...
Is there a way to fix this without having to buy a new card? I've read that the GeForce 7100 is pretty crappy, but I've got no money to space at the moment.
I recently purchased a cheap computer to use for everyday tasks. It came pre-loaded with Windows 7. The monitor I am using is a Vizio VX20L. It's native resolution is 1366X768. I have no problem with the screen resolution in Windows 7 but in Ubuntu, I am having some issues. I have the propriatary Nvidia driver installed in Ubuntu but for some reason I cannot get the screen resolution right. I am currently using a resolution of 1360x768 and the right part of my desktop is not on the screen.
I have tried to adjust the screen size using the monitor settings, but I still cannot get the whole screen to show up. If I set the resolution to Auto in the NVIDIA X Server Settings, it defaults to 1280X1024 and I can see my whole desktop, but it is streeeeetched. Here is some relevant information pertaining to my system:
I'm using Ubuntu 10.04
Integrated Video chip is NVIDIA GeForce 6150SE
The driver I'm using is NVIDIA accelerated graphic driver (version current)[Recommended]
screen is a Vizio VX20LHD
Unable to get high res, colour or 3-D acceleration working with 8.04 Hardy. Not a hardware problem as it works perfectly in dual-boot XP.
[Code]...
After closing some game my display resolution turned into 640x480 so I tried to modify xorg.conf to the following but I noticed that there are disappeared sides (at right & left) in my monitor and fonts appear small and ugly! How can I fix this issue?
[Code]...
I have installed the restricted driver, but I am stuck without a 1280x1024 video mode for any of my monitors.(Have tried 2) nvidia-settings doesn't want me to go above 1360x768, which is very strange.How do I get this thing running my optimal 1280x1024?
View 9 Replies View RelatedI have a Lenovo G550. I has a Intel GMA x4500. I use Debian Lenny 5.0.0. Changing resolution is not supported. Actually Graphic card is not installed. I have searched in packages but there is not anything in repos. I have asked my question in a forum, they told me add backports and installed the latest driver. I did, but it didn't work too. I asked abrotman and he told me : Lenny >> squeeze. But I don't want to upgrade my debian to squeeze because squeeze is unstable and I don't want to see crashing! I have googled, but I couldn't find any useful thing.
View 2 Replies View RelatedI am trying to find the maximum supported resolution of my video card by using xrandr. My card is an NVidia GeForce Go 7300 (in a laptop). The official documentation does not list specific resolutions that are supported. My laptop display is detected as "AUO" in the NVidia X Server Settings dialog (Ubuntu 10.04 amd64) and has a native resolution of 1280x800. However, I would like to know what is the maximum resolution that I could use on a display with the VGA adapter irrespective of whether the laptop's display is on. This is what I get from xrandr: Screen 0: minimum 512 x 384, current 1280 x 800, maximum 2304 x 864 default connected 1280x800+0+0 0mm x 0mm
1280x800 50.0* 51.0 56.0 52.0
1024x768 52.0 50.0
[code]....
I am guessing the maximum width of 2304 would be for using TwinView with the laptop's 1280-width display next to a 1024 CRT or similar. Surely these cannot be the only supported resolutions. I would like to use a LCD display of width somewhere around 1600 pixels (in particular while turning off the laptop's screen so as to use the external LCD as the primary display) if possible.
I read somewhere that if you run nVIDIA, that a PAE kernel won't work with it. Not supported, IIRC... Any truth to this? - My linux is (so it seems anyway) OK & I'd rather not mess it up. But I WOULD like to "use" all 4G of memory I have.
View 11 Replies View RelatedI'm running succesfully Debian 6.0 after first trying Debian 5.0 and ran into missing partitions. This is solved by using Debian 6.0 (Beta 2).
Now it's NVidia's turn: Under Ubuntu (yes...i know it by now...) you had to install a proprietary driver for NVidia to ensure that 3D was supported. What about Debian? There's nothing like this under Debian? How do i know if 3D is supported?
