I'm running CentOS 5.4 on an Atom 230-based MSI MS-7418 motherboard. I'd like to monitor this host' CPU temperature as well as the HD's temperature, but can't get lm_sensors to work:
Code:
# uname -a
Linux msi.workgroup 2.6.18-164.9.1.el5 #1 SMP Tue Dec 15 21:04:57 EST 2009 i686 i686 i386 GNU/Linux
[code]....
I did a couple searches for my Chipset and my Motherboard but I didn't get any results, I am building a Router/PBX to replace my current one and CentOS based distros are my distros of choice (Trixbox/PBX in a Flash). My new motherboard is the Jetway NC91-230-LF which has the INTEL 945GC Northbridge and an Intel ICH7 Southbridge. Which I have seen has a few known issues. When I attempt to boot the CentOS 5.2 installation or any other CentOS based OS I get the following error message:
I have also chronicalled the project at my blog.
I have decided to do away with windows for the obvious reasons. I have carried out a new instal of Ubuntu 10.04. on a formatted HDD in a Gigabyte GA-510UD atom mother board and have found that I can't install the M/B drivers from the indtall disk.
View 5 Replies View RelatedDoes anyone have any experience with the Atom processor line? How do they compare single core to single core, dual core to dual core with other Intel and Amd chips? Do they work well with linux, or are there hardware issues?
View 1 Replies View RelatedI'm running CentOS 5.4 on an Atom 230-based MSI MS-7418 motherboard. I'd like to monitor this host' CPU temperature as well as the HD's temperature, but can't get lm_sensors to work:Code: # uname -aLinux msi.workgroup 2.6.18-164.9.1.el5 #1 SMP Tue Dec 15 21:04:57 EST 2009 i686 i686 i386 GNU/Linux
# cat /etc/issue
CentOS release 5.4 (Final)
Kernel
[code]....
Trying to find the CPU temperature, I found this lm_sensors is what I need..I do this;
wget http://dl.lm-sensors.org/lm-sensors/releases/lm_sensors-3.2.0.tar.bz2
bzip2 -dv lm_sensors-3.2.0.tar.bz2
tar xvf lm_sensors-3.2.0.tar[code].....
I recently built a cluster with Centos 5.3 and nodes that used different versions of the w83627ehf sensors chip. On some nodes sensors-detect detected the chip:
Found `Winbond W83627DHG Super IO Sensors' Success!(address 0x290, driver `w83627ehf')
But starting lm_sensors returned the error: Starting lm_sensors: No sensors found!
On other nodes sensors-detect did not detect the chip at all: Found unknown chip with ID 0xb073(logical device B has address 0x290, could be sensors)
[Code]....
is it possible to run xen on intel atom or celeron for learning purposes, as when i start the virt-manager it doesn't give me the new option the file menu and when i try to do xm create domain1 it gives error like try running it with config file
if atom/celeorn can't run xen why does it gets installed on the system.
I'm trying to do a fresh CentOS 5.5 installation on a baby server with a Foxconn D51S based barebones system. BIOS is P04, the latest on their website.
When I have one 2GB memory installed, I am able to install the system and run it through some very vigorous testing without any issues. I have two DIMMs and both work just fine one at a time.
When I install two 2GB memory, it starts to crash hard during memory intensive operations, like mkfs or fsck.
I tested a 2.6.35 based kernel just in case it was an issue of old kernel + new hardware but the error persisted.
Google hasn't been helpful, and Foxconn support basically says "It runs windows, so that's good, right?").
What I've noticed is the system, when booted with one DIMM correctly reports that it has 2GB of ram (minus 8 megs for video, etc), but when I boot with both installed it seems to detect 4864MB of ram instead of the expected 4096.
Was running dual boot 10.10 and winxp on a MSI P4M900 motherboard. Have two HDs - one with OSs and some storage and the other purely backup for storage and Ubuntu home. Motherboard died and going to be replaced by Gigabyte G31 board. I will be using the same video, audio PCI cards and memory from old board. Should I look to a clean install of 10.10 and then bring back to life from my backup files (bookmarks, email etc) or could I plug in hard drives and boot normally? There is conflicting advice when I google - some say its OK just to boot, the kernel will sort out the new mboard drivers, others say you need a clean install.
View 2 Replies View RelatedThis little Atom-based unit works fine with Linux, but its fan is running at full-speed all the time.So I figured maybe lm_sensors could ajust its speed dynamically, but "sensors", "fancontrol", and "pwmconfig" all fail to work, even though the modules required for this motherboard are up and running:
Code: # dpkg -L lm-sensors
[...]
/usr/sbin/fancontrol
/usr/sbin/pwmconfig
[code]...
This little Atom-based unit works fine with Linux, but its fan is running at full-speed all the time.So I figured maybe lm_sensors could ajust its speed dynamically, but "sensors", "fancontrol", and "pwmconfig" all fail to work, even though the modules required for this motherboard are up and running:
Code:
# dpkg -L lm-sensors
[...]
/usr/sbin/fancontrol
/usr/sbin/pwmconfig
[code]....
Using the onboard gigabit ethernet interface on an Asus M2N-CM DVI motherboard (nVidia chipset) with CentOS 5.2 the ethtool utility recognises that the NIC is capable of gigabit:
# ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
[code]....
I'm trying to get audio working on a new Intel DQ67EP motherboard. lspci -v shows:
Code:
00:1b.0 Audio device: Intel Corporation 6 Series Chipset Family High Definition Audio Controller (rev 04)
Subsystem: Intel Corporation Unknown device 200f
Flags: bus master, fast devsel, latency 0, IRQ 7
[code]....
Googling around, I've learned that 6 Series Chipset blah blah is generally driven by the snd-hda-intel driver. But when I modprobe that, it isn't magically connecting to this audio chip. My kernel is Linux 2.6.27.8 #1 SMP Thu Sep 23 17:21:53 GMT 2010 i686 Intel(R) Core(TM) i7-2600S CPU @ 2.80GHz GenuineIntel GNU/Linux (derived from Slax 6.0.9) Is there a place I should be going to find newer drivers? Or perhaps there is some bleeding edge patch I should be applying? (Intel's web site is useless. They only give Windows drivers for audio. I did get the ethernet working by using their latest e1000e driver.)
I need to put a pc together for home use to act as my server. I need recommendations for a asus motherboard. I need it to support 5.3 and looking at asus website I cannot for the life of me figure out what I need. I also want to use a amd cpu. It has been years since I built my own pc and never for linux
View 3 Replies View RelatedI cannot get sound from a machine that has the M4A785-M motherboard, and a Radeon HD 4670..
My details are at: [URL]
I have a new setup, computer has only been running a couple days. The sound card is onboard, on a P7P55-M mobo. Kernel version is currently 2.6.18-128. There is no sound at all coming from the speakers.
Here are my ALSA drivers:
ALSA Driver verion: 1.0.14rc3
ALSA Lib package: alsa-lib-1.0.17-1.el5
ALSA Utils package: alsa-utils-1.0.17-1.el5
lspci:
00:1b.0 Audio device: Intel Corporation Ibex Peak High Definition Audio (rev 05) code...
The OS installed smoothly, however when I got to the desktop and wanted to go on firefox, I didn't realize I had no connection to the internet. Then I found out from the web and through the network configurations that said my NIC's driver is not installed. After many hours of researching, I could see people had similar problems with me and I tried to take those solutions and see if it'll work for me. Unfortunately it did not.
Here is my ethernet controller:
/sbin/lspci -v
02:00.0 Ethernet controller: Atheros Communications Atheros AR8121/AR8113/AR8114
PCI-E Ethernet Controller (rev b0)
Subsystem: ASUSTeK Computer Inc. P5KPL-CM Motherboard
Flags: bus master, fast devsel, latency 0, IRQ 11
[Code]....
This is a problem that I have had since Ubuntu 8.04 when the sound on my system stopped working. I have an Intel DG33BU motherboard with audio onboard.
I originally had 7.04 installed on the system (sound worked fine) and did an upgrade to 8.04 for a couple of reasons and found the sound no longer worked.
I have since upgraded to 10.10 and despite trolling various audio threads have yet to get the sound working again. I have noted that when the system boots up there is a quick message (approximately from memory) 9.32.0061: audio codec not found for hda-intel.
Is there a troubleshooting guide or information someone can point me toward as I would like to solve this problem?
I have been trying to use the information at [URL]... otingProcedure to work through the problem.
Output:
WARNING: All config files need .conf: /etc/modprobe.d/alsa-base.conf.083110, it will be ignored in a future release.
WARNING: All config files need .conf: /etc/modprobe.d/alsa-base.conf-bak, it will be ignored in a future release.
[Code]...
I recently upgraded my MBP motherboard which evidentially has an advanced graphics architecture that employs both the NVIDIA GeForce 9400M integrated and NVIDIA GeForce 9600M GT discrete graphics processors. I had no problems powering my external monitor until the MB upgrade. Now I get an xorg.conf conflict where
[root@cloudstation X11]# lspci
00:00.0 Host bridge: nVidia Corporation MCP79 Host Bridge (rev b1)
00:00.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:01.3 RAM memory: nVidia Corporation Unknown device 0a8d (rev a1)
[code]....
I'm trying to create a CentOS based liveCD that mounts a NFS share and executes one script there. The NFS never mounts altough while logged I can mount it with the very same command that I use in the KS.
In the %post I have :
%post --log=/tmp/post.log --erroronfail
mkdir /mnt/nfs
mount -o nolock 10.23.1.1:/csc/RemoteHome /mnt/nfs
I added the --log in order to debug, but nothing is written in /tmp/post.log. I tried redirection on the mount command with >> /tmp/debug.log but this is not written. Maybe during the post sequence /tmp is RO ? Anyway, I tried with ifup lo, service portmap start in the %post, but doesnt change (I even have a service : command not found in the live cd creator output).
Here is the remainder of the KS :
lang en_US.UTF-8
keyboard us
timezone US/Eastern
[Code]...
How can i add a PPPOE connection witch connect automatically on system start up in text mode in centos 5.4
View 3 Replies View RelatedHow to monitor hardware temperature (CPU , Motherboard , HDD etc) in CentOS/RHEL ?
View 3 Replies View RelatedI have a newly installed CentOS 5.4 on Gigabyte G31M-ES2C, I had to change the motherboard since it has some problems. Unfortunately the new motherboard is a rev 2.x board, which has a different onboard NIC (old one is RTL 8102E, new one is AR8132), so now my ethernet connection doesn't work anymore (no eth0 device), I assume I need to install a new driver for the AR8132? If so, what's the steps to do so?lspci shows Ethernet controller as: Attansic Technology Corp. Atheros AR8132 / L1c Gigabit Ethernet Adapter (rev c0)
View 3 Replies View RelatedI am trying to clone a working Centos 5.4 system onto a new box with a ASUS P5KPL-CM motherboard. I have done so by plugging in a Realtec lan card - but can't get the motherboard lan working. Googling tells me the motherboard has a Atheros L1E lan chip - but I have installed several kmod drivers from ELREPO - but still can't get the on-board lan working. So far I have installed:
kmod-atl1e
kmod-atl1
I have just installed these with yum - but no new hardware appears in the network gui dialogue. Am I missing some step here - or is there another driver I should be looking for.
First time I am having issues with Centos.
I bought a Intel DQ45CB LGA Q45 Micro ATX Motherboard and I am installing the 64 bit version of centos.
The install of Centos goes just fine. However when I first try to boot up, after post is done, I get a blank screen. I do not even get on the Grub screen. No access to any of the ttys. No access to anything, files, folders. I only get a blkinking cursor, no command prompt, nothing.
This happened with Centos 5.2 and 5.3
Just for the hell of it, I installed XEN Xitrix and I have no issues like that.
I have a system built and running in exactly the basic configuration I want, with my recompiled kernel, extra packages, special drivers, everything works, life is good. What I want to do is take this exact setup and create an image I can copy onto a bootable USB stick. Is there a way to essentially take the contents of my hard drive and copy that onto a USB stick and then boot directly from that? The use case behind this is that I am building an embedded system of which I may have hundreds of boxes with identical hardware and software configurations. Instead of hard drives, I am going to use USB sticks for cost efficiency and maintenance. My idea is that when it's time to upgrade, I could just image a hundred new sticks and go out and swap them.
My issue is that a standard LiveCD install gets me maybe 25% of the way to a finished system. I need to recompile the kernel for realtime support with my CPU, add some fidgety drivers for some specific hardware, and install a whole bunch of additional packages. I suppose I could create a makefile(s) to replicate all the manual steps of the buildout but that seems like a lot of unnecessary complexity IF I can just image that running system as it is.
I searched and found several solution but those are distro specific. I need to find out if distro is running in live mode (from CD, USB) instead it's installed on hdisk. The solution should be independent of distribution.
View 7 Replies View RelatedIm trying to install a trading program fx trading station II on a dedicated virtual server that's linux based at media temple. Any ideas on how to run the program so that the exe file isn't prompting to download the file instead of prompting the user to login and trade?
View 2 Replies View RelatedI managed to get lm-sensors working it has no initialization at bootime:Quote:Do you want to generate /etc/sysconfig/lm_sensors? (yes/NO): yCopy prog/init/lm_sensors.init to /etc/init.d/lm_sensorsfor initialization at boot time.You should now start the lm_sensors service to load the requiredkernel modules.I've already copied 'prog/init/lm_sensors.init' to '/etc/init.d/lm_sensors' but it doesn't work. I still have i manutally have to load 'coretemp' to be able to have a temperature output from the command "sensors"
View 5 Replies View Related