CentOS 5 Hardware :: P5QL Pro Motherboard's NIC Not Detected With 5.5?
Nov 17, 2010
The OS installed smoothly, however when I got to the desktop and wanted to go on firefox, I didn't realize I had no connection to the internet. Then I found out from the web and through the network configurations that said my NIC's driver is not installed. After many hours of researching, I could see people had similar problems with me and I tried to take those solutions and see if it'll work for me. Unfortunately it did not.
Here is my ethernet controller:
/sbin/lspci -v
02:00.0 Ethernet controller: Atheros Communications Atheros AR8121/AR8113/AR8114
PCI-E Ethernet Controller (rev b0)
Subsystem: ASUSTeK Computer Inc. P5KPL-CM Motherboard
Flags: bus master, fast devsel, latency 0, IRQ 11
[Code]....
View 5 Replies
ADVERTISEMENT
Mar 3, 2010
Just installed CentOS 5.1 and it's not detecting my NIC. ifconfig produces nothing for eth0. This is a xen kernel.
I can't tell exactly what NIC this motherboard uses, the ASUS website doesn't seem to think we need to know anything more than that it's a PCIe Gigabit lan:
[URL]
lspci indicates it's an Atheros AR8121/AR8113/AR8114.
View 5 Replies
View Related
May 20, 2011
how to i get ubuntu to use my on board gfx card because it can't find it. games that run super fast in windows are bogged down(and proably rendering using the cpu) and it was enough for cube and cube 2.any command i can use to scan for the mobo card or is it called something totally different than a VGA
View 9 Replies
View Related
Mar 3, 2009
Using the onboard gigabit ethernet interface on an Asus M2N-CM DVI motherboard (nVidia chipset) with CentOS 5.2 the ethtool utility recognises that the NIC is capable of gigabit:
# ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
[code]....
View 8 Replies
View Related
Feb 3, 2009
I did a couple searches for my Chipset and my Motherboard but I didn't get any results, I am building a Router/PBX to replace my current one and CentOS based distros are my distros of choice (Trixbox/PBX in a Flash). My new motherboard is the Jetway NC91-230-LF which has the INTEL 945GC Northbridge and an Intel ICH7 Southbridge. Which I have seen has a few known issues. When I attempt to boot the CentOS 5.2 installation or any other CentOS based OS I get the following error message:
I have also chronicalled the project at my blog.
View 11 Replies
View Related
Jul 24, 2009
I need to put a pc together for home use to act as my server. I need recommendations for a asus motherboard. I need it to support 5.3 and looking at asus website I cannot for the life of me figure out what I need. I also want to use a amd cpu. It has been years since I built my own pc and never for linux
View 3 Replies
View Related
Feb 24, 2010
I cannot get sound from a machine that has the M4A785-M motherboard, and a Radeon HD 4670..
My details are at: [URL]
View 7 Replies
View Related
Mar 24, 2010
I have a new setup, computer has only been running a couple days. The sound card is onboard, on a P7P55-M mobo. Kernel version is currently 2.6.18-128. There is no sound at all coming from the speakers.
Here are my ALSA drivers:
ALSA Driver verion: 1.0.14rc3
ALSA Lib package: alsa-lib-1.0.17-1.el5
ALSA Utils package: alsa-utils-1.0.17-1.el5
lspci:
00:1b.0 Audio device: Intel Corporation Ibex Peak High Definition Audio (rev 05) code...
View 1 Replies
View Related
Apr 1, 2010
I recently upgraded my MBP motherboard which evidentially has an advanced graphics architecture that employs both the NVIDIA GeForce 9400M integrated and NVIDIA GeForce 9600M GT discrete graphics processors. I had no problems powering my external monitor until the MB upgrade. Now I get an xorg.conf conflict where
[root@cloudstation X11]# lspci
00:00.0 Host bridge: nVidia Corporation MCP79 Host Bridge (rev b1)
00:00.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:01.3 RAM memory: nVidia Corporation Unknown device 0a8d (rev a1)
[code]....
View 1 Replies
View Related
Jun 7, 2011
How to monitor hardware temperature (CPU , Motherboard , HDD etc) in CentOS/RHEL ?
View 3 Replies
View Related
Jan 17, 2010
I have a newly installed CentOS 5.4 on Gigabyte G31M-ES2C, I had to change the motherboard since it has some problems. Unfortunately the new motherboard is a rev 2.x board, which has a different onboard NIC (old one is RTL 8102E, new one is AR8132), so now my ethernet connection doesn't work anymore (no eth0 device), I assume I need to install a new driver for the AR8132? If so, what's the steps to do so?lspci shows Ethernet controller as: Attansic Technology Corp. Atheros AR8132 / L1c Gigabit Ethernet Adapter (rev c0)
View 3 Replies
View Related
Apr 8, 2010
I am trying to clone a working Centos 5.4 system onto a new box with a ASUS P5KPL-CM motherboard. I have done so by plugging in a Realtec lan card - but can't get the motherboard lan working. Googling tells me the motherboard has a Atheros L1E lan chip - but I have installed several kmod drivers from ELREPO - but still can't get the on-board lan working. So far I have installed:
kmod-atl1e
kmod-atl1
I have just installed these with yum - but no new hardware appears in the network gui dialogue. Am I missing some step here - or is there another driver I should be looking for.
View 5 Replies
View Related
Jan 1, 2010
I'm running CentOS 5.4 on an Atom 230-based MSI MS-7418 motherboard. I'd like to monitor this host' CPU temperature as well as the HD's temperature, but can't get lm_sensors to work:
Code:
# uname -a
Linux msi.workgroup 2.6.18-164.9.1.el5 #1 SMP Tue Dec 15 21:04:57 EST 2009 i686 i686 i386 GNU/Linux
[code]....
View 6 Replies
View Related
Jun 8, 2010
First time I am having issues with Centos.
I bought a Intel DQ45CB LGA Q45 Micro ATX Motherboard and I am installing the 64 bit version of centos.
The install of Centos goes just fine. However when I first try to boot up, after post is done, I get a blank screen. I do not even get on the Grub screen. No access to any of the ttys. No access to anything, files, folders. I only get a blkinking cursor, no command prompt, nothing.
This happened with Centos 5.2 and 5.3
Just for the hell of it, I installed XEN Xitrix and I have no issues like that.
View 2 Replies
View Related
Mar 17, 2010
I just recently changed my motherboard, and now the command "sensors" shows "no sensors detected" I ran sensors-detect but still i get no sensors detected.
View 9 Replies
View Related
May 15, 2009
I have an issue with Hard Drives in GNU/Linux CentOS 5.3I installed linux 5.3 frash copy to new SATA MAXTOR 1000GB Hdd.And see the partitions is SATA MAXTOR 1000GB (NEW INSTALLATION CentOS 5.3)
/dev/sda1 Boot
/dev/sda3 /
(/dev/sda2 is the SWAP)
[code].....
View 5 Replies
View Related
Oct 13, 2009
I am new to cent os. I have install cent os 5 in my HP laptop. I updated my cent os also. But it is not detecting the wireless signals.
View 2 Replies
View Related
Feb 28, 2011
I try to setup a HPC cluster with CentOS 5.5. But now there is no Internet connection available in the room where the hardware is located so I set up ntpd server using synchronization with local clock (maybe I do something wrong). Here is my ntp.conf file on a master node (the master node has IP 10.0.1.1, a file server has IP 10.0.1.2 and compute nodes are 10.0.1.3..10.0.1.11, comments are omitted):
restrict 127.0.0.1
restrict -6 ::1
restrict 10.0.1.1 mask 255.255.255.255 notrust[code].....
View 1 Replies
View Related
Feb 8, 2010
I am new to Linux and after a lot of research I settled on CentOS to be my OS for Linux. But I am having trouble with sound right now as I can not play audio. The command system-config-soundcard opened a gui for audio configuration saying following device is detected - Intel Corp. 82801(ICH9 Family) HD Audio Controller.
Ouput for some commands are given below::
[root@localhost ~]# lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) .....
[root@localhost ~]# uname -r
2.6.18-164.el5
[root@localhost ~]# cat /etc/redhat-release
CentOS release 5.4 (Final)
Clicking on the volume icon gives me message that either Gstreamer plugins are not installed or sound card is not configured.
While Trying to install gstreamer using YUM, I got following message:
[root@localhost ~]# yum install gstreamer
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile .....
Setting up Install Process
Package gstreamer-0.10.20-3.el5.x86_64 already installed and latest version
Package gstreamer-0.10.20-3.el5.i386 already installed and latest version
Nothing to do
[root@localhost ~]#
So I guess gstreamer are installed but how to configure the sound card or is there any other problem.
View 9 Replies
View Related
Feb 17, 2010
Aspire One D250 wlan/ethernet not working on centos 5.4i have tried alot, searchingon net to findout the both lan card drivers for my new aspire one d250 but coudn't find out. Please help me in finding and installing the drivers. infact i have seen alot people searching for the same but no one has successfully installed any of the lan.
View 2 Replies
View Related
Aug 20, 2010
I haven't manually configured XWindows in a very long time, so I'm not very certain what I need to do anymore. Hopefully someone can provide some guidance. I just built up a new system that I'm trying to connect to a 47" LCD TV that provides a VGA connection. When the computer starts booting all of the text comes up just fine (1 or 2 characters on the left are chopped, but otherwise fine). When I tried to run the installer for CentOS5.5 I ran into a problem. The monitor(TV) wasn't getting a proper signal to display XWindows. In an effort to keep going, I reconnected the PC to an old monitor and did the install from there. That worked no problem. I ran all the latest updates hoping that maybe this was fixed in a patch. I then shutdown and reconnected to my TV. no luck. When it starts XWindows the screen doesn't display anything. I've tried fooling around with modifying the xorg.conf and adding an explicit "Monitor" section and set it to 640x480 with a VertRefresh of 60 (which is supposedly an acceptable format), but no luck. Can anyone provide any guidance on how to solve this problem. BTW I do know that the VGA connector on the TV works just fine because I can hook up my laptop (Windows XP) to it.
H/W Monitor: Olevia 747i (when nVidia on my laptop detects it, it is reported as 747-b11) Motherboard: Biostar MCP6PB M2+ Motherboard - Socket AM2+, �ATX, Audio, GeForce 6150 Graphics, SATA, RAID Graphics: Using the integrated GeForce 6150 chipset
View 7 Replies
View Related
Dec 24, 2010
I have installed ubuntu and Centos 5 , but when i do sudo update-grub , the new centos 5 is not detected. Some days ago i did the same (i installed ubuntu , and then Centos 5) , but i had to format the hard disk because some problems i had. The thing is that in that first time update-grub worked , but now not , why? Shouldn't be detected this time too? I have to manually add the new entry to the grub no?
View 4 Replies
View Related
Feb 23, 2009
I'm in rescue mode with Centos 5.2 disk trying to install/mount a new disk to extract data out from the failed server.
Plugged in a new SATA drive and syslog shows the drive being detected
SCSI device sdg: blah
sdg: Mode Sense: 00 3a 00 00
sdg: unknown partition table
sd 3:0:0:0: attached scsi disk sdg
However fdisk and mount does not find the drive. I tried echo "---" /sys/class/scsi_host/host3/scan based on one of the previous threads but get "write error: invalid argument".
how should I get the drive to be usable?
View 4 Replies
View Related
Sep 2, 2010
Just installed updates with the recent kernel update 11.3 for Centos 5.5. I have had guest additions running fine before that. Now when I try to reinstall the guest additions (which is necessary) I get the message Detected Unsupported x86 environment. how to get this going since it was running fine before the kernel update.
View 7 Replies
View Related
Mar 23, 2010
If I boot CentOS (5, up to date) without my USB headphones are plugged in, all sound output goes to the sound card. But if I have the headphones plugged in when I boot, all output goes to them, and the sound card does not seem to be recognised at all.
Is there any way I can force the sound card to be recognised, and chosen as the default device, when booting with the headphones plugged in? If I have booted with the headphones plugged in, and then I unplug them, go into System|Preferences|Sound, and press the Test button with sound playback set to autodetect, I get a dialog with the message: audiotestsrc wave=sine freq=512 ! audioconvert ! audioresample ! gconfaudiosink: Could not open audio device for playback.
Then I started System|Administration|Soundcard detection, and it detected both Intel and Radeon sound cards, but its test button did not produce any sound for either. I moved the Intel device to the top of the list in the Settings tab, and then ran "Reload audio drivers" in the System tab. I got an error message saying I needed to reboot, but I didn't. At this point, the test buttons in the Sound test tab, and in System|Preferences|Sound started working OK. Do I have to go through this rigmarole every time I boot with the headphones plugged in?
View 3 Replies
View Related
Jun 13, 2010
how to detected sound card or drivers.when i am trying to detect sound card by using command system-config-soundcard it gives output on gui mode (Audio Configuration) but there is nothing show on PCM device. System Configuration which i am using.
#uname -a
Linux *** 2.6.18-8.el5 #1 SMP Thu Mar 15 19:46:53 EDT 2007 x86_64 x86_64 x86_64 GNU/Linux
#lspci
00:00.0 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a1)
[code]....
View 3 Replies
View Related
Feb 26, 2010
I have installed trixbox 2.8.0.3 in Intel MAC mini PC, installation completed successfully. After reboot network card was not detected.
My MAC mini PC comes with nVidia Corporation MCP79 Ethernet card. how to enable Ethernet card with out affecting the tribox. trixbox-2.8.0.3 version comes with Cent OS 5.4. [Moderator edit: s/deducted/detected/]
View 5 Replies
View Related
Nov 29, 2010
In our company, we have one server with kernel, 2.6.18. because of our neads, we had to buy new hard disk,that slax live cd detects that as "Ibex Peak 2 port SATA IDE Controlle".Apparently this kernel does not support this device.Unfortunately according to our policy(definitely some dependency on company's softwares installed on this kernel) we can not upgrade our kernel.
View 1 Replies
View Related
Mar 27, 2009
My centos_5.2 kernel is 2.6.18-92.1.22.el5_i686, I installed openswan-2.6.14-1.el5_2.1.rpm on my system.After that , everytime I restart my system, this error will always occured:padlock: VIA padlock not detectedpadlock: VIA padlock not detectedI hope someone could tell
View 2 Replies
View Related
Mar 17, 2011
I am currently running Fedora 14 on a 32-bit AMD XP motherboard. My plan is to replace the motherboard w/an AMD 64-bit (multicore, prob'ly) version (most likely w/a different h/w architecture) and I'd like to make sure my current applications and configuration (if that makes any sense) are moved en masse to the 64-bit version.
Is there an easy way to do this? What are my "gotchas"?
View 14 Replies
View Related
