Red Hat / Fedora :: "Unknown Error 513 In Pthread_create After Several Hours Of Running A Gstrea?

Nov 18, 2010

I am using Gstreamer for creating one of my video streaming application. My application creates multimedia session and then stream around 200 video sessions (a very processor intensive job).In doing so, the no. of threads created is around 1500 and I have given around 1536 KB as my stack size for each of these threads. I have one Quadcore(intel Xeon) system of around 8 GB of RAM(64 bit) with RHEL 5.5(kernel - 2.6.18-92.el5). After few hours of testing I see that my overall memory(RAM) is eating up. I did checked the memory and I saw that my cache size is growing. So far so good, as I can understand that system does cache instead of leaving some RAM free.
My problem comes, when I see that after almost 20-25 hours of testing, RAM is continuously being eaten up and maximum part of that is going into cache. If I leave the system for few more hours I see whole of my memory is consumed up and now my swap started getting used. If I check the cache now, I clearly see most of RAM is now in form of cache. I still didn�t stop my application and allowed it run for few more hours and after sometime I see that process give segmentation fault while creating the pthread (create_pthread::unknown error 513).I also tried to observe the �core� file of application created in this way , but it doesn�t� show anything.

One thing I must mention that, in �top� I see almost constant values of resident memory, virtual memory and shared memory. There is no increase of memory usage here. So here I can assume that my application is not leaking the memory. I also observed that if I kill my application any time during this, the memory doesn�t go into free pool. Anyone, here can give any pointer for this kind of behavior. Is it can be because of some kernel BUG which is not freeing the memory to application usage.

View 1 Replies


ADVERTISEMENT

OpenSUSE Install :: Grub Error 18 - Unknown File System - Running From External Hard Drive

Jan 11, 2011

It started when I wanted to dual boot Windows 7 and Opensuse off of my netbook (No DVD/CD drive) I tried install suse from an external hard drive and I botched it. I ended up erasing EVERYTHING off of my internal netbook hard drive. Windows and all.

Well, I had a couple of other computers so I studied up and eventually successfully installed OpenSUSE 11.2 on my external hard drive (11.3 being the one that I accidentally erased everything with, so kinda scared of it) and now I want to install openSUSE 11.2 on my internal netbook hard drive.

I can not use disks

I can not use a flash drive (For some reason, even if I make it bootable, it will not load up, this could be because it's actually a 8GB microSD card that is placed in a USB card reader.)

I can not use an external hard drive because that's what I'm running suse off of.

I've tried reading up on how to install suse on another drive off of the hard drive and I've gotten as far as whenever I boot up the netbook with the suse external hard drive connected it will ask to boot into OpenSUSE, the Fail Safe, or to install OpenSuse. When I select to install it it gives me the Error 18 Unknown File system.

I've tried formatting the internal hard drive twice. One as NTFS and again as EXT4. Neither seems to effect it other than when it's ext4 I can open it and it contains a Lost and Found folder.

When I interrupt the boot sequence by pressing c and going to the terminal and I use the root (hd +TAB command it tells me I have a hd0 and a hd1. The hd1 only has 1 partition which is ext4, which I'm assuming hd1 is the internal hard drive (I'm not sure how to check) and the hd0 is the external hard drive, which has three partitions. One with an unknown file system and two with ext4. When I try to enter the set up from the terminal it gives me the same error for any thing I put it (e.g. root (hd0,0) gives the same error as root (hd0,1), or root (hd0,2) and root (hd1,0)

Something like it cannot locate these two files I'm assuming it needs to boot. If anyone finds this relevant I'll retry it and post the files its missing.

I've been searching for awhile and can't find any threads that can solve my problem. From other threads, however, I have noticed that I should probably include my menu.lst, listed below

Code:

I have also ran the boot info script and received the RESULTS.txt file it generates. Listed below

Code:

View 9 Replies View Related

Fedora :: Undefined Reference To `pthread_create' When Install Bochs And Make The Makefile

Oct 26, 2009

when i install bochs and make the makefile why undefined reference to `pthread_create'

View 1 Replies View Related

Ubuntu :: Error "unknown Applications Running" On Shwutdown

Aug 1, 2010

When i shutdown or restart, i get this error [URL] it says that an applications its running, but all is closed here my top processes [URL] what is the applications that running because the pop-up says "unknown applications", top semms regular to me. what is it this application?

View 7 Replies View Related

CentOS 5 :: Getting "Unknown Error" When Running System-config-xxxx Programs?

Aug 6, 2010

I am a long time Unix system admin and this one has got me stumped.When I try to run the system-config-network (or any of the system-config-xxx programs) from the links on the GNOME interface, I get a message pop-up that says, "Unknown error" and no additional information. I have also opened a terminal and run it from the command line (/usr/bin/system-network-config) and I get the same "Unknown error" pop-up. I was not the one who originally configured this server, so I am not sure of the history or how it might have been broken. I can't seem to find any debugging information or even any command line parameters that might give me a clue what the complaint is. There is no error number or any other helpful hint as to the cause of the problem.

I have been manually editing the config files so the server is up and running but it is tedious to manage the server without the GUI.Has anyone seen this before? I assume it is a configuration issue, but I am not sure where to look.uname -aLinux xxxxserver 2.6.18-164.15.1.el5 #1 SMP Wed Mar 17 11:30:06 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux/etc/redhat-releaseCentOS release 5.4 (Final)

View 3 Replies View Related

Fedora :: Evolution - Error While Sending Message. Failed To Append To : Unknown Error Appending To Local 'Sent' Folder Instead

Jan 28, 2011

When I send mail via Evoultion it does seem to send ok but still the following error message comes up: Error while sending message. Failed to append to : Unknown error Appending to local 'Sent' folder instead. Not sure what's up with that but thought I would mention it.

View 3 Replies View Related

Ubuntu :: Fan Stops Running After A Couple Hours?

Apr 17, 2011

I am unsure if this is a hardware problem or a linux problem. My machine is only 3 months old so it is not the fan. I didn't have problems until recently, and after the latest kernel update it got worse - having to restart more frequently.

I do not experience the fan turning off in windows. I use thinkfan when I have to but it isn't a very good program for an every day basis. The fact I can force start the fan with thinkfan when it turns off leads me to believe it is a kernel issue.

View 4 Replies View Related

Fedora X86/64bit :: 24 Hours Format To 12 Hours Format Lovelock?

Jul 27, 2011

I have a problem,I want to change the hour format from 24 hours to 12 hours, I cant find the way to do this,

View 14 Replies View Related

Fedora :: Konqueror Unknown Host Error

Jul 25, 2011

When I open Konqueror, on Fedora 15 KDE, it opens to the default Start Page just fine. When I try to visit any other website, it gives me an Unknown Host Error. The documentation I found for KDE just said that if I get that error, it means that either the website does not exist or I am not connected to the internet, but I'm quite sure I'm connected to the internet.

View 6 Replies View Related

Fedora Servers :: Gnome Error - Hostname: Unknown Host

Mar 23, 2009

I installed Gnome on my server by when I run

Code:

[root@F026 ~]# startx

Code:

hostname: Unknown host
xauth: creating new authority file /root/.serverauth.2915
X.Org X Server 1.5.3
Release Date: 5 November 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.18-128.1.1.el5 i686

[code]...

I don;t have physical access to the system and it is a server located in Europe. Fedora release 10 (Cambridge) is installed in it.

View 2 Replies View Related

Red Hat / Fedora :: Boot Error Mount: Unknown Filesystem Type 'ext4'

Feb 5, 2010

i am trying to compile kernel 2.6.23 on Fedora 12 After fixing a few bugs (getline error, %dil ,etc) i was able to compile the kernel made initramfs img using dracut updated grub and then booted up the new kernel 2.6.23 but it fails to boot with following error mount: unknown filesystem type 'ext4'

View 8 Replies View Related

Fedora Servers :: Sendmail[31427]: Unable To Open Berkeley Db /etc/sasldb2: Unknown Error 13

Sep 7, 2010

I've been using cyrus and sendmail together for a very very long time now. Just recently I upgraded to fedora 13 and now my virtual users can not send email from the /etc/sasldb2 passwords. I get in the /var/log/messages sendmail[31427]: unable to open Berkeley db /etc/sasldb2: Unknown error: Its weird that they can still log in and get email from imapd.conf

sasl_pwcheck_method:auxprop saslauthd
sasl_auxprop_plugin: sasldb
sasl_mech_list: LOGIN PLAIN CRAM-MD5 DIGEST-MD5

[code].....

I even tried re-creating sasldb2 and sasldblistusers2 shows my two users 'one' that is also a local user account and the saslauthd authenticates when sending emails, but the virtual user 'two' can't send just only can log in to receive. /etc/sysconfig/saslauthd is set up as mech=pam. but I don't see how that would be relevant to this issue.

View 5 Replies View Related

Programming :: Pthread_create Does Not Return The PID ( Process ID)?

Aug 5, 2010

I am using pthread_create system call to create a thread. However pthread_create does not return the PID ( process ID). Is there any quick way to fınd the PID of the created thread.

View 1 Replies View Related

CentOS 5 :: Install CentOS 5.2, And The Installation Ran Out Of Disk Space After Running For About 2 Hours?

Feb 18, 2010

I am trying to install CentOS 5.2, and the installation ran out of disk space after running for about 2 hours.I checked the FAQ, and it said 1.2 GB. The disk is 3 GB. The default install was selected, and I think that it checks for sufficient available disk space before installing. Still, it ran for quite a while before announcing that it was out of disk space.The Installation Guide is not very helpful, since there is a blank page where the disk space requirement is supposed to be. I just picked the default installation. A search of the forums on "not enough disk space" did not return much.

View 13 Replies View Related

Programming :: Undefined Reference To 'pthread_create' From Linker?

Jul 6, 2010

I am having trouble linking the pthread library.I have -lpthread -lm as options for the GNU GCC compiler.

Build Log
Compiling: main.c
Compiling: matrix.c

[code]...

View 2 Replies View Related

General :: Grub Loading Wait Error 21 - System This Way For Hours

May 16, 2010

Grub loading wait error 21 - system this way for hours

View 4 Replies View Related

OpenSUSE :: Unknown Application Is Running

Mar 31, 2011

After a series of unrelated problems with my mouse (that had nothing to do with suse) I opened a process but I don't know what is it. It looks like a series of micro-post-its in the bottom of my desktop:Also, I checked the option to start a new session every time I start KDE, but this keeps appearing.

View 9 Replies View Related

Ubuntu :: Unknown Process Always Running?

Mar 8, 2011

Maybe someone can shed some light on this process that is running. It is using my CPU about 100% since there are 2 instances of it running with about 50% used by each.abc_sieve_2.10_i686-pc-linux-gnuI've never noticed it running before and don't think I've installed anything except updates.

View 6 Replies View Related

Ubuntu :: Error - The Configuration Could Not Be Saved - An Unknown Error Occurred

Oct 4, 2010

Whenever I try to change a user full name, through System / Administration / Users and Groups, I get the following error: The configuration could not be saved - An unknown error occurred. Running Ubuntu 10.04.1 LTS 64 bit, freshly installed.

View 2 Replies View Related

Server :: Error - Iptables: Unknown Error 18446744073709551615

Feb 9, 2010

When i try to add value 150 on portflood section of csf,i get following error:

iptables: Unknown error 18446744073709551615 PORTFLOOD tcp opt -- in !lo out * 0.0.0.0/0 -> 0.0.0.0/0 tcp dpt:80 state NEW recent: UPDATE seconds: 5 hit_count: 150 name: 80 side: source

Error: iptables command [/sbin/iptables -v -A INPUT -i ! lo -p tcp --dport 80 -m state --state NEW -m recent --update --seconds 5 --hitcount 150 --name 80 -j PORTFLOOD] failed, at line 996

how is limitation with ip_recent where highest value for hit_count is 20,and how i need to modify and recompile ip_recent.But i was not able find anything about either modify or recompiling that module.I have cent os 5.4 64 bit,iptables are installed over yum.Also i have 4 servers with completely identical configuration,yet on two servers portflood works while on other two it reporting that error.Maybe it was different install cd which caused this,but again i dont know why this doesnt work since iptables version are indetical.

View 1 Replies View Related

Fedora :: Skype Sound Error "ALSA Lib Pcm.c:2211:(snd_pcm_open_noupdate) Unknown PCM Default"

Dec 9, 2009

Skype now runs, but there is an error when attempting to use voice. When opened in terminal the error is thus: ALSA lib pcm.c:2211:(snd_pcm_open_noupdate) Unknown PCM default Over and Over again. Am I missing a 32 bit library on my 64 bit machine? EDIT: Smiley face not intended

View 4 Replies View Related

Red Hat / Fedora :: "installation Failed: Unknown Error"

Apr 5, 2010

when i try to install a .rpm after the installation is finished it appear "installation failed: unknown error"

View 6 Replies View Related

Fedora :: 15 Crashes After A Few Hours

Jun 6, 2011

I've recently moved from Ubuntu (after moving from Gentoo and Arch) to Fedora 15 and am experiencing some crashing.

What happens is after a few hours or not particularly hard usage (web browser, a couple of terminals, maybe having run a few Ant scripts etc) all the fans seem to go into serious overdrive. I can't move the mouse and the system doesn't respond to any keyboard input. After about five minutes of this, the fans slow down but the system remains unresponsive. I've left it for a further 30 minutes, still nothing so I have to do a hard reset.

My hardware is a stock laptop Compal IFL90. Besides the standard installed software, the only other things I've installed are;

- Sun JDK (and Eclipse, but not running during crash)
- Pogo Plug software (pogoplugfs which is started on login)
- Cryptkeeper for my encfs stuff
- Opera

Can anyone point me to a possible fix, or let me know what other information is needed to try and get more complete support? It's not to much of a problem at the moment, but when I start using my laptop more frequently, having to power cycle every few hours is going to make is to difficult to use.

Code:

View 3 Replies View Related

Server :: Host Unknown Error:Sendmail / Stat=Host Unknown (Name Server: Def-fgh.com.: Host Not Found)?

Sep 8, 2009

Many of mails sent from my mail server that are in Queue;The main reason is deffered by domains like yahoo,aol,etc.but there is one more error that i keep getting and that is Host Unknown,Below is an example from mail log,The catch is,test mail sent on the same email id sent from my personal mail from the same server i.e. url was deliveredHowever,another mail containing client information sent from customercare@mycompanysdomain ended up in queue.

There are more examples of the same,around 20 domain have the same problem.

Sep 7 14:33:46 server2 sendmail[24591]: n8793jiC024589: to=<abc@xyz.fi>, delay=00:00:00, xdelay=00:00:00, mailer=esmtp, pri=163672, relay=xyz.fi., dsn=5.1.2, stat=Host unknown (Name server: xyz.fi.: host not found)

Sep 7 22:09:42 server2 sendmail[6407]: n87Gdffa006403: to=<abc@def-fgh.com>, delay=00:00:00, xdelay=00:00:00, mailer=esmtp, pri=152474, relay=def-fgh.com., dsn=5.1.2, stat=Host unknown (Name server: def-fgh.com.: host not found)

View 2 Replies View Related

Red Hat / Fedora :: Error On Running Yum Update

Jan 19, 2010

[code]...

how to fix the problem?

View 2 Replies View Related

Fedora :: Time Keeps On Changing 7 Hours

Sep 18, 2010

I have an Asus laptop with both Win7 and Fedora. Whenever I change the time in Fedora to the correct time and reboot into W7 the W7 time is messed up - about 7 hours earlier. If I set W7's time to the correct time and then reboot to Fedora, Fedora's time is then 7 hours early. For some reason I can't get both OS's to agree it's the same time.

View 10 Replies View Related

Fedora :: Getting Error While Running AVI File Using Totem

Jun 19, 2009

While trying to run avi file using totem, I get error. As I tried to "search" as used by totem, I get:
$ totem A Walk To Remember.avi
** Message: don't know how to handle video/x-divx, divxversion=(int)3, framerate=(fraction)2997/125, width=(int)640, height=(int)272
** Message: don't know how to handle audio/mpeg, mpegversion=(int)1, layer=(int)3, rate=(int)48000, channels=(int)2, codec_data=(buffer)010002000000880101000000
** Message: Error: You do not have a decoder installed to handle this file. You might need to install the necessary plugins .....
How can I get the codecs?

View 3 Replies View Related

Fedora :: Getting Error On Running Any Video File?

Nov 5, 2010

I get this error if I try run any video file [URL].

View 4 Replies View Related

Software :: Error Running G2ipmsg-0.9.6 In Fedora-6?

Jun 14, 2010

I have configured g2ipmsg-0.9.6.But when i am trying to run "g2ipmsg" executable from command line,i am getting following error:

Error : [fileubcrypt.c line:1307 ] Can not store key: length: 0
Error : [fileubcrypt.c line:1307 ] Can not store key: length: 0
Error : [fileubcrypt.c line:1307 ] Can not store key: length: 0

[code]....

View 4 Replies View Related

Debian :: Transmission 1.22 Stopped Downloading \ Get An Error Message Tracker Responded: Unknown Error (0) In The Info Window, Tracker Tab?

Nov 14, 2010

I have a problem with Transmission. After using it for over six months without a single problem, it suddenly stopped downloading. In the torrents that do no get downloaded, I get an error message Tracker responded: Unknown error (0) in the info window, tracker tab. But there are torrents with the same tracker that don'thave a problem and get downloaded fineThe logs don't give a clue about whats wrong either.I tried downloading those torrents with Vuze and I had the same problem. What could be wrong?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved