I have purchased an ASUS PCE-N13 wireless card (PCI Express card). My PC doesn't actually detect that it is actually physically present.Would anyone have any idea on exactly what I should do. I have run a diagnostic script which outputs the following though I am uncertain what to do.
View 8 Replies1 ) make and model of wireless device Athreos 5k
2 ) driver version in use dont know
3 ) any error message. -
abhishek:/ # sudo /usr/sbin/iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a
Flags: bus master, fast devsel, latency 0, IRQ 23
Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
[code]....
I have searched and have not found anything specific to my issue. I am currently using NDISWrapper to load the bcmwl15 driver and when it's active it works beautifully.Problem is sometimes at boot, the card doesn't "turn on" and I don't know how else to describe it. The OS does not even detect that the hardware is present. I have disabled wireless hotkey in BIOS. The only way to make the wireless card "active" is to reboot with the wiredconnection to the router. After doing that the wireless card "wakes up" and works awesome.Is there anything I can do to make sure the driver load at boot?mes I get the error that NDISWrapper is not modprobbed when I go to network configuration and if I wish to do i now? I don't know if that has anything to do with the boot sequence. Using the <modprobe ndiswrapper> command as root does nothing permanant
View 9 Replies View RelatedI searched this forum for posts similar to the problem I am having and i found a few, but I did not understand the solution (unexperienced user here) so I thought i would ask.I recently installed fedora 13 on my laptop and everything appears to be detected, with the exception to my wireless card (a broadcom 43225 card).I checked the list of drivers that came with installation and i could not find one for this particular card. is there any way for me to get a driver that would work with it (maybe a more general driver, just something to make it possible to connect over the internet) Or is it
View 7 Replies View RelatedI have just upgraded from 9.10 to 10.04 and now my wireless card isn't being detected as far as I know. It was working perfectly in the previous version. At the moment I've physically put an ethernet cable straight to the router.
[code]...
I bought a new TOSHIBA C660 - i5010 today and installed.Lucid Lynx 10.04 on it, but it has not detected my wirelessg broadcom 80211 (STA) driver debp interface.
View 1 Replies View RelatedI have linux mint on my Macbook but it is almost exactly like ubuntu, so here goes. I have a Macbook, about a year old, and when i use linux, the wireless card is not detected. Any site to download drivers at?
View 2 Replies View Relatedim having some trouble connecting the wireless card to my wifi network, theres is a hint using the terminal
remora@remora-laptop:~$ sudo lshw -C network
[sudo] password for remora:
*-network DISABLED
description: Wireless interface
[code]....
i just installed debian after about 2 weeks of using ubuntu afterriend suggested switching, and it's not detecting my wireless card in the network settings. i'm new at linux so try to keep it simple if you can please,i read the sticky about this and here's the info it said i should provide
ispci -knn Code: 00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07)
Kernel driver in use: agpgart-intel
[code]...
I have a Acer Revo R3610 nettop on which I installed oS11.3. It has an Atheros AR5001 wireless network adaptor.I'm getting very bad latency and throughput on with this card. In comparison my Thinkpad with Intel card achieves at least 10 times the throughput from the same location. Also when I boot my wifi will come up authenticate and then a few seconds later disconnect and reconnect. I've tried updating the kernel to 2.6.35 as one of the fixes was to improve the performance of the ath5k driver. I'm using wpa2 authentication.
Here are some details:
Code:
mediacentre:~ # /sbin/lspci -nnk
00:00.0 Host bridge [0600]: nVidia Corporation MCP79 Host Bridge [10de:0a82] (rev b1)
Subsystem: Acer Incorporated [ALI] Device [1025:0222]
[code]....
Is there anything else I paste that will help determine the cause of the bad throughput. Browsing the web or copying files across the network is bordering unusable.
I have configured a wireless pcmcia card using ndiswrapper. I'm sure that works, as with the command "iwlist wlan0 scan" gives me back
the list of detected wireless networks. At this point I was wondering: is there a way to detect the new interface (wlan0) with network manager? Even after enabling the wifi card the network manager gnome applet always finds only eth0.
i have the cd just do not know how to install the driver for my linksys wireless pci card 14e4:4329the device is BCM43XG
View 4 Replies View Relatedwhen it comes to openSUSE but I am earnestly trying. I installed the openSUSE OS on my HP dv6000 laptop, but it does not seem to recognize my wireless card (which is a Broadcom 4311).
View 7 Replies View RelatedMy wireless device is an integrated Dell Wireless 1397 WLAN Mini-Card, I am unsure about the driver I have in use. I am sure I have a driver installed because the configuration screen shows my network. I currently have the computer plugged into my network via CAT 5 but I would like to be able to use the wireless (obviously.) I am using Open SuSE version 11.2 and I have run the updater. I could not see my wireless network before running the updater and I can now so I know that the updates have helped but I am again stuck. I have tried to search the wireless forum and I have tried to tinker with the settings in YaST , but nothing seems to be working. Reading the Welcome page of the wireless forum, I tried the Broadcom chip-set advice:
[Code]...
I have read and taken to heart the advice given for receiving help and if any more is needed I will gladly give it. I have a small amount of experience with SuSE Enterprise edition so I can understand some technical stuff but I am best at following specific instructions.
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies View Relatedturn wireless card on for the Dell Studio 16 (1645) for SUSE 11.2 64-bit.
View 3 Replies View RelatedI have a Toshiba Satellite L550 laptop with Suse 11.3 dual booting with Windows 7. Windows can detect the built in wireless card but not Suse, what can I do to get the wireless recognized in Suse.
View 2 Replies View RelatedI have Dell 1537 laptop having Intel 5100 wireless card. It is not supported by Fedora 9. I have tried downloading the driver iwlwifi-5000-ucode-8.24.2.12.tgz from URL...Downloads and copied it to folder /lib/firmware and rebooted the machine. But still it is not detected by the system. Is there any solution to this problem .
View 2 Replies View RelatedI have installed Fedora 14 on my new laptop Thinkpad T410 but the wireless card is not detected.
I tried to install the drivers but got error. How to install the driver.
[root@sheril sheril]# lspci
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) .....
I started on ubuntu 8.10 and my wireless card has always worked,Since i did a fresh install of ubuntu 10.04 it still seems to work to a point.I can see networks, click them and use a password to connect but it never seems to carry on, I typed the password correctly and after a minute it asks for it again.I have read a post about problems other people are having and that i need to install a different program.But i cant install another program if there is no wireless as apt-get doesn't work without internet connection.So... I need to download something that will fix it (possible update if one has been released) to xp (partition) then access xp partition from ubuntu and install it.
View 9 Replies View RelatedI have an issue with wireless connectivity on my laptop. Its a HP dm3 and the intel network adapter is supported as I can scan and detect wireless access points.However, when I attempt to connect to my home network, it fails and this is probably a result of two things: The BSSID is missing and/or the DHCP client ID is missing.I am running Kubuntu 10.10 32 bit
View 2 Replies View RelatedWireless card detected but cannot connect to a wireless network
I have install it suse 11, and everything went well until the wireless thing is not working, my card is Broadcom BCM4318, I see my card on the network settings but I cannot configure the card, and also I cannot connect to a wireless network, can someone tell me what to do here, I am loosing my patient....
I want to load Atheros wireless card to ubuntu linux OS having kernel 2.6.32.21. I have loaded the atheros driver and I observed the following log messages when card was inserted.
[ 55.732223] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[ 55.732294] pci 0000:04:00.0: reg 10 32bit mmio: [0x000000-0x00ffff]
[ 55.810152] ath5k: disagrees about version of symbol ieee80211_free_hw
[code]....
My suspect was the driver was 2.6.35.1 kernel based i may need to update my kernel, but i have other laptop having 2.6.32-21 kernel and this card works fine.
I am running the latest version of arch linux on a Dell Latitude D420. So far everything has worked perfectly except the wireless. It seems that Arch does not even detect the wireless because ifconfig -a only gives me the loopback and eth0. I installed ndiswrapper as well as the drivers. lsmod | grep ndiswrapper shows that ndiswrapper is being loaded on boot. I tried to install the iwp3945 drivers, but they have become obsolete so pacman was unable to find them. I also tried installing the iwl3945 drivers as explained here [URL] but still no luck.
View 14 Replies View Relateddell laptop and went out on thenet looking for a solution for my failed wireless interface. i downloaded the firmware but then my interface still fails to come on after a reboot.
wlan0 IEEE 802.11bg ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
[code]...
I am running SLED 11 and My Networkcard is Intel PRO/Wireless 5300. In short, it is not there anymore! I mean I was connected and everything and the next time I restarted It could not detect any wireless network. I deleted the wireless network card in hopes that the OS will automatically detect it on startup and set it right but NOPE. When I check the hardware information in YAST, it is listed there and it is also working under Windows.
View 4 Replies View RelatedI have downloaded and installed Fedora 10.Now I am setting up the network and in the 'network configuration' it finds the wireless device (ralink) in the 'hardware' section of the configuration - I set this to eth0 (it originally set itself to wan0 and I still had the same problems, now it doesn't give me the option to put it back to wan0).Now I goto the devices tab and try to set up the device with eth0 - which it seems to find.But when I goto activate the device it tells me that eth0 cannot be found
View 2 Replies View RelatedBeen using Ubuntu for 1 yr now on my Dell Dimension 8250 but a newbie with my Averatec AV3270-EH1 laptop circa 2005. Ubuntu 10.04 does not detect the Integrated WLAN card/adapter. I've looked at all the forums/posts but none had the issue I have. When I type lspci into the terminal i get this back:
00:00.0 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
00:00.1 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
[code]....
And when I type in iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
Want to eventually make the switch over but figure taking it slow and learning on an old laptop would be best.
I went through the installer and everything looks great so far except I can't for the life of me seem to be able to get the wireless working. I tried everything a windows newb like me could think of ... it looks like to me the wireless card is not being used since it can't detect anything? I read some threads and here are the results of common terminal stuff that most people say to do:
/sbin/lspci
Code:
00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 03)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 02)
02:01.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev 01)
code....
I don't know how install my wireless card.in Yast, i see it, but I can not configure it... I configure with ndiswrapper, but it's not work.
View 5 Replies View Related