OpenSUSE Wireless :: Intel 3945abg Wireless Network Card Cannot Connect To Router Automatically
Apr 8, 2010
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies
ADVERTISEMENT
Mar 2, 2010
I am unable to get my intel pro/wireless 3945abg connected to my router. The firmware has been installed and at first was even able to connect, but now the access point doesn't even show up in network manager. I am currently able to connect using a USB wireless adapter, but for certain reasons, would prefer to use the former. I've looked over this page with no results.
View 7 Replies
View Related
May 21, 2010
I have an IBM Thinkpad T60, running Ubuntu 10.04 (Lucid) with a dual boot of Windows XP. I am having trouble getting it to connect to my home wireless network, which uses WEP. It connected fine at my university when I first installed Lucid, but has not connected at home. I can see the network in the panel applet, with a good signal strength, but when I try to connect it repeatedly asks me for my key and never actually connects. I had this problem shortly before I installed Lucid, though it was working for a long time previously. I'm not sure what update caused it to stop working because I was at my university at the time, and it works fine there even now, so I didn't realize it right away.
I doubt this is a hardware issue because I can connect to the same network when I boot into Windows. I have seen posts about similar problems on the forums, but couldn't find any solutions that helped me.
Below is the information the wireless help guide said to post. Machine Brand and Model: IBM Thinkpad T60
Wireless Brand, Model, and Wireless Chipset: lspci -nn | grep 'Wireless'
Code:
03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4227] (rev 02)
Check Interface:
ifconfig wlan0
[Code]...
View 5 Replies
View Related
Apr 17, 2010
at start, knetworkmanager detect wireless network, but doesn't automatically connect - I have to restart it to make it work properly. Instead, it gives that error:
[Code]...
View 2 Replies
View Related
Apr 23, 2011
It's also because I've never had any big problem. The last openSUSE I used without problems was/is 11.2(I still use it as main desktop because of problems since 11.3).The problem is - the DL speed is repeatedly drops down to around 156KB/s albeit my top speed of router-NIC combination is at 21-22MB/s. When this happen and open network manager and click/reload my wifi or restart wireless or even computer, the speed is back at the top. But after few seconds, minutes it drops down again, and so on. I made some images(to see it on the network manager draphs):after that drop-off:and restart wireless:Best chance to see it is when downloading more files with FreeRapidDownloader or JDownloader. Upload speed is OK. The first time I've seen this problem in 11.3, which i've skipped in hope that 11.4 will be ok and now, as the EOL of 11.2 is coming I'd like to go on.It's also desktop and installation media independent(Gnome works similar, DVD, LiveCD).I've checked many other distributions and none of them had this problem. But openSUSE is my love, so i need and want to solve it
View 9 Replies
View Related
May 5, 2011
wlan0 Authentication capabilities :
WPA
WPA2
CIPHER-TKIP
CIPHER-CCMP
Those are my authentication capabilities, obviously. I am using a WEP encryption for my wireless router and according to this, it will not allow me to connect. Is there anyway to allow that? The wireless card works just fine in Windows, even on the same network encryption type. Using a Intel Wireless/Pro 4965 ag. Note* this is my mother's router and whatnot. She won't change it the encryption type.
View 2 Replies
View Related
Jun 30, 2011
I installed a Tenda W322P wireless card in my dual-boot PC running both Windows XP and Ubuntu 11.04. The card worked straight out of the box on XP, but does not function correctly under Ubuntu. My apologies for any missing/irrelevant information, I am having to post this from the Windows boot so the Ubuntu settings are not directly available at the same time as internet access.I followed the process detailed here htURL...to install and configure the driver (I believe from reading other sites that this card is the Ralink RT3062 chipset), blacklisted the original RT2860 driver that was in use (couldn't even get the card to scan for wireless networks with the default driver) and restarted the interface.
Since then, sudo iwlist scan can find my wireless router but when I attempt to connect to it, it seems to enter a loop of requesting the WEP key then pausing for a while before re-requesting the key. I know I have the key value correct because it is copied and pasted from the same text file I used to copy and paste into the passkey field on the Windows boot. Attempting to connect to the router using Ubuntu also has the rather unfortunate side-effect of crashing the wireless router, killing off all other device connections until the router has been reset.
View 2 Replies
View Related
Jul 15, 2010
I did a fresh install,I also enable the networkmanager.after installation,my wireless unable to connect to my router . when I click to connect , it prompt for password then after that nothing happen.
View 8 Replies
View Related
Mar 17, 2011
Desktop that has wireless built into motherboard worked in 11.3 (as best as I can remember, don't really use it normaly). Trying to connect to my wireless router (only one I have rights to).Wireless router is WEP with opensystem authentication, works fine for laptop (Windows)Networkmanager scans and displays local networks
Networkmanager shows:
acivating
setting network address
connection failed
[code]...
View 3 Replies
View Related
Apr 15, 2010
All settings are correct as far as i can tell. The wep key works on all my windows boxes. When i have connect automatically enabled it never tries to connect. if I go to edit it it pops kde wallet up i put in credentials. wallet goes away then nothing happens. if i double click connection to my router also nothing happens. I have the wep key in there and i even made it visible to make sure.
View 5 Replies
View Related
Apr 14, 2010
I am running openSUSE 11.2 and just recently my network has been down. I'm using Gnome, but using Yast to configure my network (I'm usually forced to use wireless as I travel a lot on my laptop). Usually, when I'm connected to a wireless network, it will show up as so in the Gnome start menu, but recently, it will only say Wired there, even though I have nothing connected to my ethernet jack. I can connect wirelessly to a home router, but cannot use the wireless in any other way. I have tried manually disabling the ethernet connection to no avail. Unfortunately I am limited in my linux knowledge, so I am kinda stuck here.
View 1 Replies
View Related
Jan 6, 2010
What do you think? Wife just bought a new Compaq 610 series laptop. These are the wireless specs:
Code:
10:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)
30:00.0 Ethernet controller: Marvell Technology Group Ltd. Unknown device 4357 (rev 10)
Strange thing is when I ping the router, I get this, pings one time then dies:
Code:
anna@katie:~$ ping 192.168.0.1
PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.
[Code]...
View 9 Replies
View Related
Aug 5, 2009
I'm new to linux and I install ubuntu on my wifes laptop since it will hopefully slow down the amount of problems I have to resolve.I ran the live cd of ubuntu and wireless was working all ok, showed my wife around and she was like ok install it.I used the GUI and install ubuntu, and updated (apt-get update) after that the wireless is not working.I see the device, but have no idea whats wrong. Please could someone inform me as to which things to post in order to get it sorted. Since this seems to be the only issue.
View 2 Replies
View Related
Jun 6, 2010
I can connect to my wireless router while logged in as root, but not under my user account. I went into YAST and the user maintenance area and gave myself every permission (Add, Edit, Delete Users or Accounts), but kde network maanger will not allow me to connect to my router.
View 5 Replies
View Related
Apr 24, 2010
I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.
Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.
Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).
The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.
Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).
Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.
Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).
My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?
Here is a link to (picture) my network diagram. Network Diagram
View 2 Replies
View Related
Jun 17, 2011
The problem with my wireless network. I have Dell DV6 Pavilion 2115 eg laptop and i installed Ubuntu 11.4 and internet and wireless worked, until i reboted my system it has disapear. I cant no longer to connect to a wireless network. It dont shows me any wireless network. My wireless card is Atheros AR 9285 802.11b/g/n Wifi Adapter
View 9 Replies
View Related
Feb 24, 2010
how would i connect to the Internet in Ubuntu with the Intell 3945AGB driver? I can't find anyway to do this.
View 9 Replies
View Related
Oct 27, 2010
I installed Maverick earlier today on a Dell XPS M1210, and everything works beautifully, except for one thing: the wireless card. It is an Intel 3945ABG wireless card, and I've tried searching around and have found nothing,
View 7 Replies
View Related
Oct 5, 2009
I've been trying to configure this wifi on CentOS 5 this whole weekend =(. Here's the details:I'm currently doing this link:
[URL]
I'm not sure if I've configured correctly mac80211, but here's what on my lsmod and other details, let me know what else you need:
[root@mortonlx morton]# /sbin/lsmod | grep mac
mac80211 117453 0
compat 7617 1 mac80211
[code]....
View 6 Replies
View Related
Jun 28, 2011
I need help configuring to set my wireless to connect automatically on boot up. Right now I do have wallet on with a password.
View 1 Replies
View Related
Jan 12, 2010
i've installed openSuse 11.2 on my laptop (dell studio 15).Today at work i tried to connect to the wireless network, but i couldn't. First, the network card wasn't being recognized, but after a long time trying i was able to set it up, for this i used this command:
Code:
zypper in broadcom-wl broadcom-wl-kmp-desktop
So now, the networkmanager detects all the networks around, but i cannot (or i don't know
[code]...
View 8 Replies
View Related
Feb 22, 2010
I have my laptop dual booted between Ubuntu 9.10 and Windows 7. In Ubuntu I randomly lose connection to the wireless network. It always works fine when I first boot into Ubuntu but after a while my wireless connection will go down. The signal strength meter will go to zero bars and the black popup message will appear that my wireless connection has disconnected. At first, if I just wait a bit, the connection will come back. However, after about 4 or 5 times of doing this it will then ask me for my password, and inputting the password does not reconnect me to the AP. I am finally forced to reboot. Then it works OK for a while again and the cycle repeats.
It works fine in Windows7 all day, every day. I have the Release Candidate of Windows7 so it's going to expire soon. I would really prefer to make Ubuntu my everyday OS on this laptop rather than pay for a Windows7 license but I cannot tolerate a flaky wireless connection.
I had 8.1 on this laptop at one point and I never had any problems with the wireless then, that I can remember. I had no Ubuntu for a while but then I came back with the 9.1 and was loving it until the wireless problem reared it's ugly head.
Wireless found by lspci: 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
View 1 Replies
View Related
Aug 11, 2011
I'm new to linux. I've just installed Ubuntu 11.04. It has all been going ok, but the wireless just stopped working all of a sudden. The indicator light turned off and when I tried to turn it back on (Fn+F2) nothing happens. Sometimes, when I restart the computer, the wireless might work; but if the signal is lost the LED on my laptop turns off and I cannot reconnect. Also, in these strange cases that the wireless works when I restart I can manually turn it off (Fn+F2), but nothing happens when I try to switch it back on.
In the menu on the upper right corner I see 'Enable Networking' is checked, but 'Enable Wireless' cannot be modified.
I have a Dell Inspiron 6400 and the wireless device is an Intel Pro/Wireless 3945ABG.
I have tried to follow some of the threads on this forum on similar cases, but the ones that were comprehensible to me did not work (or I actually might not have understood them either). code...
View 1 Replies
View Related
Sep 15, 2011
wifi card:atheros ar5007egOS: openSUSE11.4My laptop can't connect on network after system hibernate. It has been asking me for enter the wifi password. But when I input the wifi password it still can't connect on network. I have to reboot it.
View 3 Replies
View Related
Jun 20, 2010
I'm try to setup a wireless network with my linksys wireless router and my HP laptop dual booting Vista & Suse 11.2. I have the vista networked, just fine. Where I can share files and the printer connected to my desktop. But I want to be able to use Suse in the same way, full time and to stray away from Vista. My wife and kids like easy. So I'm trying to transform them and show them something new.
View 9 Replies
View Related
Nov 13, 2009
My wireless is not working after a fresh install of OpenSUSE 11.2. I cannot connect in KDE or Gnome. I installed cnetworkmanger and I can't get anything to connect. My wired network card on this laptop has been down for a long time. All I have is wireless. I have to roll back today to 11.1 if I can't fix it, but I really have been looking forward to 11.2 for some time. This is really a stupid bug to have in supposedly production ready software. Maybe I should add that in KDE knetworkmanager does not load by itself. I have to load it manually via console every reboot. I get this:
> knetworkmanager
Object::connect: No such signal QTreeWidget::itemDoubleClicked(QTreeWidgetItem*)
Object:: connect: (sender name: 'twNetworks')
It puts the icon in the system tray, and annoyingly hides it, so it took me a while to evern realize it was there. When I point my mouse at it, it says "Networking Information Not Available". When I click it, it says Network Management Disabled. cnetworkmanager spews out a bunch of errors and finishes by saying it can't find any .service files. I configured the device via 'Network Devices' in YaST. Hardware info says it is using the iwl3945 kernel driver. Everything was fine in OpenSUSE 11.1 and 11.0.
View 9 Replies
View Related
Mar 23, 2010
When i click the button to connect to a wireless network this message apears:Network management disabled
View 1 Replies
View Related
Aug 1, 2010
My son lost his USB Wireless stick for his Computer. I had thought I heard that if you had a second wireless router, you could use it somehow to detect the wireless router you have already set up in your home (like using a wireless card)? Is this what Ad-Hoc is? Either way, can this be done and if so how? I use a WRT54Gx2 Lynksys router and have a TRENDNET TEW-432BRP wireless router and also a spare D-link DI-514. I use ubuntu 10.04, and also wanted to know if I connected one of the router to his on the LAn port could he connect msaybe through an Ad-Hoc on my local computer here? He uses XP on his. I'm a newbie to linux and networking in general.
View 2 Replies
View Related
Jun 4, 2010
Intel 5100 wireless card doesn't connect on 10.04?
View 1 Replies
View Related
Sep 19, 2009
RT2500 wifi card could not connect to wireless router using WPA personal.OS - RHEL4; Dell Inspiron C600; interface detected ra0
View 12 Replies
View Related
