OpenSUSE Wireless :: Add New Wireless (rt3070sta) Card To Opensuse
Mar 9, 2011
How can I add a network card to Network Manager? I have installed a new usb dongle and iwconfig shows it, ifconfig -a shows it and iwlist shows my SSID. Network manager just does not list it. A side note: It is weird if I use my old bulky Zonet (rt2870sta) on reboot it is wlan0 but if I plug in my new Edimax (rt3070sta) it will not show up unless I reboot with it and only it plugged in. Then I can plug in my Zonet again and they show up as ra0 and ra1.
I have a Acer Revo R3610 nettop on which I installed oS11.3. It has an Atheros AR5001 wireless network adaptor.I'm getting very bad latency and throughput on with this card. In comparison my Thinkpad with Intel card achieves at least 10 times the throughput from the same location. Also when I boot my wifi will come up authenticate and then a few seconds later disconnect and reconnect. I've tried updating the kernel to 2.6.35 as one of the fixes was to improve the performance of the ath5k driver. I'm using wpa2 authentication.
Is there anything else I paste that will help determine the cause of the bad throughput. Browsing the web or copying files across the network is bordering unusable.
abhishek:/ # sudo /usr/sbin/iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a Flags: bus master, fast devsel, latency 0, IRQ 23 Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
I have searched and have not found anything specific to my issue. I am currently using NDISWrapper to load the bcmwl15 driver and when it's active it works beautifully.Problem is sometimes at boot, the card doesn't "turn on" and I don't know how else to describe it. The OS does not even detect that the hardware is present. I have disabled wireless hotkey in BIOS. The only way to make the wireless card "active" is to reboot with the wiredconnection to the router. After doing that the wireless card "wakes up" and works awesome.Is there anything I can do to make sure the driver load at boot?mes I get the error that NDISWrapper is not modprobbed when I go to network configuration and if I wish to do i now? I don't know if that has anything to do with the boot sequence. Using the <modprobe ndiswrapper> command as root does nothing permanant
when it comes to openSUSE but I am earnestly trying. I installed the openSUSE OS on my HP dv6000 laptop, but it does not seem to recognize my wireless card (which is a Broadcom 4311).
My wireless device is an integrated Dell Wireless 1397 WLAN Mini-Card, I am unsure about the driver I have in use. I am sure I have a driver installed because the configuration screen shows my network. I currently have the computer plugged into my network via CAT 5 but I would like to be able to use the wireless (obviously.) I am using Open SuSE version 11.2 and I have run the updater. I could not see my wireless network before running the updater and I can now so I know that the updates have helped but I am again stuck. I have tried to search the wireless forum and I have tried to tinker with the settings in YaST , but nothing seems to be working. Reading the Welcome page of the wireless forum, I tried the Broadcom chip-set advice:
[Code]...
I have read and taken to heart the advice given for receiving help and if any more is needed I will gladly give it. I have a small amount of experience with SuSE Enterprise edition so I can understand some technical stuff but I am best at following specific instructions.
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
I have a Toshiba Satellite L550 laptop with Suse 11.3 dual booting with Windows 7. Windows can detect the built in wireless card but not Suse, what can I do to get the wireless recognized in Suse.
dell laptop and went out on thenet looking for a solution for my failed wireless interface. i downloaded the firmware but then my interface still fails to come on after a reboot.
I am running SLED 11 and My Networkcard is Intel PRO/Wireless 5300. In short, it is not there anymore! I mean I was connected and everything and the next time I restarted It could not detect any wireless network. I deleted the wireless network card in hopes that the OS will automatically detect it on startup and set it right but NOPE. When I check the hardware information in YAST, it is listed there and it is also working under Windows.
I have purchased an ASUS PCE-N13 wireless card (PCI Express card). My PC doesn't actually detect that it is actually physically present.Would anyone have any idea on exactly what I should do. I have run a diagnostic script which outputs the following though I am uncertain what to do.
First of all, trying to install it was a disaster as it tried to format my DVD drive and I was forced to delete my Windows partitions too. That's not why I'm writing, just thought I'd mention that I was already frustrated to begin with
Anyway, I have an HP G62-340US laptop. Everything seems to be running great except that I cannot turn on my wireless. The laptop has a key on the keyboard to power up the wifi and it's permanently off. Not sure if this is an issue with the keyboard driver, but pressing the wifi key does nothing.
I've tried scanning the hardware to determine what wifi device I have, but since it's not powered up, Linux doesn't even see it.
Any ideas which direction I should look?
As a side note, I have used Linux fairly regularly for several years. Mostly Ubuntu, LinuxMint and PinguyOS (all debian-based). So I'm not a complete newbie and am perfectly comfortable with the command line and configuration files.
Want to eventually make the switch over but figure taking it slow and learning on an old laptop would be best.
I went through the installer and everything looks great so far except I can't for the life of me seem to be able to get the wireless working. I tried everything a windows newb like me could think of ... it looks like to me the wireless card is not being used since it can't detect anything? I read some threads and here are the results of common terminal stuff that most people say to do:
Has anyone managed to get wireless Ralink rt3070 drivers working in Lucid? Before in Karmic, you could "sudo modprobe rt3070sta" as they were "stagging" drivers already in the kernel, but apparently they're missing from the kernel in Lucid as reported here [URL]... I get errors when compiling the latest drivers from Ralink (DPO_RT3070_LinuxSTA_V2.3.0.2_20100412) and they don't seem to work.
My first problem is that when I open KNetworkManager the wireless tab is desibled,I don't know why! My laptop is HP pavilion dv6-1245DX. How to get connected to my wireless router?
I have an acer lab top and OpenSuSE 11.2 installed but now the wireless card is not working. With ubuntu I had a tool called jokey to install missing drivers. Does there exist a jockey version (rpm not deb) for OpenSUSE or is there i simillar tool.
I have a dwa-125 dlink wireless card which will not work. This is my first time using OpenSuse 11.2 (Well OpenSuse period). I had the same problem with Ubuntu 9.10 as well. If it will help the solution I used with Ubuntu is here: [ubuntu] Dlink DWA-125 Wireless Card Issue - Page 4 - Ubuntu Forums. I'd rather use OpenSuse than Ubuntu.
I can't get on the Internet at all not even through Ethernet. (It recognized my Ethernet hardware but doesn't connect.) I got the broadcom-wl drivers from Packman and installed those and it still was a no go. I tried to get the drivers straight from Broadcom and those didn't work. I couldn't compile the source code from the Brodcom site because i could not get build installed (got make installed but build just didn't install.)
Info:
Card BCM4322 When I enter /sbin/lspci -nnk Code: 00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory
So decided to try a fresh install as ubuntu was having issues every update for me. Regardless i can't seem to get my wireless working and i'd really appreciate some help as i have no idea what i'm doing.
Using a hp pavilion dv5 1235dx.So my network card does show up it's a broadcom 4312 pci id 4315.Installed the b43 & wl drivers but it didn't help. The hardware switch is stuck at orange but in ubuntu it would function despite this(sometimes ).
I have a local 3G data card which i need to set up on each boot using terminal. I have searched a HELL LOT and found a way to do it. The following are the commands to be run :
I am trying openSUSE after a long break from Linux, but I am running into the original issue I ran into several years ago which made me decide not to use this distro. My LAN card is working fine, and I can get internet hardwired into my router, but I am not having any luck getting my wireless card recognized or working. Also, my notification area on my taskbar (sorry for the Windows terms) is not showing any sort of network status icon.
I have gone Computer>Install Software> and installed the b43 fwcutter thing from the repos, and have also run the following command in terminal: sudo /usr/sbin/install_bcm43xx_firmware In Network Settings in YaST, my NIC is showing, but I am still not seeing my Wireless card.
I've got an old Compaq Armada laptop (850 mhz PIII processor, 512mb RAM, 30GB HD, DVD ROM) that I've been running OpenSUSE 11.1 on in a dual boot configuration with WinXP for almost a year. I've downloaded and burned a LiveCD of OpenSUSE 11.2 and booted the computer with it. Very impressive. I want to install it on the HD without doing a clean install. That is, I want to replace 11.1 and keep the WinXP partition intact. My biggest trepidation is getting the wireless card configured again. It was a bear the first time. Is there a way to update OpenSUSE without losing those settings?
I have a AR928X wireless card and everything I have tried has failed. The default driver ath9k scans and connects to my router but cant connect to any site or ping anything , same with the madwifi driver lspci prints 02:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01)
