I have an acer lab top and OpenSuSE 11.2 installed but now the wireless card is not working. With ubuntu I had a tool called jokey to install missing drivers. Does there exist a jockey version (rpm not deb) for OpenSUSE or is there i simillar tool.
View 1 RepliesI have a dwa-125 dlink wireless card which will not work. This is my first time using OpenSuse 11.2 (Well OpenSuse period). I had the same problem with Ubuntu 9.10 as well. If it will help the solution I used with Ubuntu is here: [ubuntu] Dlink DWA-125 Wireless Card Issue - Page 4 - Ubuntu Forums. I'd rather use OpenSuse than Ubuntu.
View 4 Replies View RelatedI am trying openSUSE after a long break from Linux, but I am running into the original issue I ran into several years ago which made me decide not to use this distro. My LAN card is working fine, and I can get internet hardwired into my router, but I am not having any luck getting my wireless card recognized or working. Also, my notification area on my taskbar (sorry for the Windows terms) is not showing any sort of network status icon.
I have gone Computer>Install Software> and installed the b43 fwcutter thing from the repos, and have also run the following command in terminal:
sudo /usr/sbin/install_bcm43xx_firmware
In Network Settings in YaST, my NIC is showing, but I am still not seeing my Wireless card.
I have a AR928X wireless card and everything I have tried has failed. The default driver ath9k scans and connects to my router but cant connect to any site or ping anything , same with the madwifi driver
lspci prints
02:00.0 Network controller: Atheros Communications Inc.
AR928X Wireless Network Adapter (PCI-Express) (rev 01)
I read through the sticky of wireless card not working, and I followed through with the steps, with the exception of looking for firmware, because I'm certain it has it, being that the card works when I'm running Windows, and overall the system recognizes the device.
The only difference is, I notice that the activity light on the card itself does not turn on when running openSUSE. It recognizes the card, it even detects the network, but when I enter the WEP key and finish, it does nothing afterwards. Still no internet.
Card: Linksys WMP54G v4.1
Well this my first time working with linux and openSUSE, and I love it. But one problem I can't overcome is my network card is not working. I went to bestbuy and bought the dynex enchanced wireless G card.
Model # dx-ebnbc
ver. 1011
I installed wine to run the .exe but that did nothing and gave me that the dll is not registered. openSUSE detects that the card is plugged in but the card does not light up or activate in anyway. The only way I can connect to the net is through an Ethernet cable.
To become familiar with unix I decided to install a partition of openSUSE. I'm currently running 11.4 and how to get my wireless card working. I know that I have an RTL8188CE. I downloaded the realtek drivers from Realtek However, when I try to execute the make command I get the following error:
make: *** /lib/modules/2.6.34.7-0.5-default/build: No such file or directory. Stop.
make: *** [all] Error 2
I've made sure that I've installed the packages in both the base development and the C, C++ packages. I looked under the base development package and know for sure that i have make installed. I'm not really what i'm missing
A wifi card with the ath5k driver used to work properly until a couple of weeks ago. Now, if I ping the router the response times sometimes are okay but often fluctuate into the range of many hundreds or thousands of milliseconds. Occasionally the connection breaks down entirely.My laptop, which uses a different card, works fine (typical ping response times of 2 ms), so its probably not the router which is faulty.I use opensuse 11.3 x86_64, currently with the 2.6.34.7-0.7 desktop kernel and knetworkmanager
View 1 Replies View RelatedI just got myself a Dell Inspiron 1440. And decided to install my favorite distro Debian. I got the installation to go with no issue and all seems to be working fine. However the wireless isn't working. NetworkManager doesnt even detect a wireless card. I followed the instructions here and installed the b43-fwcutter and then issued the modprobe b43 and modprobe b43legacy commands. Then I issued the iwconfig command and this was the output.
[Code].....
Also, I've been doing some research and found out about some file located /etc/udev/rules.d/70-persistent-net.rules. So I looked in mine and found out that only my eth0 is added.
[Code].....
I want to convert my laptop to Linux only machine. My Wireless card is Netgear WG511 and from the little research I have done it is not going to work under Linux. What is an easy to get working Wireless card? I have a Dell Inspiron 8500 and I plan to install Ubuntu 9.10.
View 12 Replies View RelatedI'm running Fedora 14. Sabrent PCI-G802 PCI Wireless Card - 54Mbps, 802.11g, Windows/Mac/Linux Compatible [URL]. I bought this card (under $20) and it worked out of the box. I'll be buying the Sabrent N PCI (which they make) card once I upgrade my network/router.
View 1 Replies View RelatedI have a Acer Revo R3610 nettop on which I installed oS11.3. It has an Atheros AR5001 wireless network adaptor.I'm getting very bad latency and throughput on with this card. In comparison my Thinkpad with Intel card achieves at least 10 times the throughput from the same location. Also when I boot my wifi will come up authenticate and then a few seconds later disconnect and reconnect. I've tried updating the kernel to 2.6.35 as one of the fixes was to improve the performance of the ath5k driver. I'm using wpa2 authentication.
Here are some details:
Code:
mediacentre:~ # /sbin/lspci -nnk
00:00.0 Host bridge [0600]: nVidia Corporation MCP79 Host Bridge [10de:0a82] (rev b1)
Subsystem: Acer Incorporated [ALI] Device [1025:0222]
[code]....
Is there anything else I paste that will help determine the cause of the bad throughput. Browsing the web or copying files across the network is bordering unusable.
i have the cd just do not know how to install the driver for my linksys wireless pci card 14e4:4329the device is BCM43XG
View 4 Replies View Related1 ) make and model of wireless device Athreos 5k
2 ) driver version in use dont know
3 ) any error message. -
abhishek:/ # sudo /usr/sbin/iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a
Flags: bus master, fast devsel, latency 0, IRQ 23
Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
[code]....
I have searched and have not found anything specific to my issue. I am currently using NDISWrapper to load the bcmwl15 driver and when it's active it works beautifully.Problem is sometimes at boot, the card doesn't "turn on" and I don't know how else to describe it. The OS does not even detect that the hardware is present. I have disabled wireless hotkey in BIOS. The only way to make the wireless card "active" is to reboot with the wiredconnection to the router. After doing that the wireless card "wakes up" and works awesome.Is there anything I can do to make sure the driver load at boot?mes I get the error that NDISWrapper is not modprobbed when I go to network configuration and if I wish to do i now? I don't know if that has anything to do with the boot sequence. Using the <modprobe ndiswrapper> command as root does nothing permanant
View 9 Replies View Relatedwhen it comes to openSUSE but I am earnestly trying. I installed the openSUSE OS on my HP dv6000 laptop, but it does not seem to recognize my wireless card (which is a Broadcom 4311).
View 7 Replies View RelatedMy wireless device is an integrated Dell Wireless 1397 WLAN Mini-Card, I am unsure about the driver I have in use. I am sure I have a driver installed because the configuration screen shows my network. I currently have the computer plugged into my network via CAT 5 but I would like to be able to use the wireless (obviously.) I am using Open SuSE version 11.2 and I have run the updater. I could not see my wireless network before running the updater and I can now so I know that the updates have helped but I am again stuck. I have tried to search the wireless forum and I have tried to tinker with the settings in YaST , but nothing seems to be working. Reading the Welcome page of the wireless forum, I tried the Broadcom chip-set advice:
[Code]...
I have read and taken to heart the advice given for receiving help and if any more is needed I will gladly give it. I have a small amount of experience with SuSE Enterprise edition so I can understand some technical stuff but I am best at following specific instructions.
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies View Relatedturn wireless card on for the Dell Studio 16 (1645) for SUSE 11.2 64-bit.
View 3 Replies View RelatedI have a Toshiba Satellite L550 laptop with Suse 11.3 dual booting with Windows 7. Windows can detect the built in wireless card but not Suse, what can I do to get the wireless recognized in Suse.
View 2 Replies View RelatedI have a DELL Vostro 1500 and I have Debian Lenny running on it. I did get the wireless card BCM4312 working but after doing apt-get update followed by apt-get upgrade and after rebooting it stopped working. I am including the output from iwconfig, ifconfig and lsmod.
raygo75@RayGo-d3:~$ sudo ifconfig eth1
[sudo] password for raygo75:
eth1
Link encap:Ethernet HWaddr 00:16:44:9b:e9:cc
inet6 addr: fe80::216:44ff:fe9b:e9cc/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:17 Base address:0xc000
I think I will mentions that I got the wireless card working after following the instructions at [URL]
I have an HP Pavillion tx1410us and I cannot seem to get my wireless card working or recognized. I am not sure if I need another driver, or I need to start another service. I am running Fedora 12 64 bit.
View 5 Replies View RelatedI've installed 10.04 on a Dell 1200 laptop and cannot get the wireless card working. I've tried getting Ndiswrapper but it doesn't appear to be available on 10.04, and since I don't have an Internet connection, I can't download it. The card is a Broadcom Corp BCM4306 802.11 b/g. How do I get the card connecting to my Linsksys?
View 7 Replies View RelatedI installed 10.10 on my 2nd laptop with the SAME internal wireless card as my other laptop, but Ubuntu all of a sudden acts like I have no wireless card? When I click on the network icon in the panel, Wireless Connections is enabled, but Ubuntu shows no available wireless networks? I can switch to my other laptop and it works fine.
View 9 Replies View Relateddell laptop and went out on thenet looking for a solution for my failed wireless interface. i downloaded the firmware but then my interface still fails to come on after a reboot.
wlan0 IEEE 802.11bg ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
[code]...
I am running SLED 11 and My Networkcard is Intel PRO/Wireless 5300. In short, it is not there anymore! I mean I was connected and everything and the next time I restarted It could not detect any wireless network. I deleted the wireless network card in hopes that the OS will automatically detect it on startup and set it right but NOPE. When I check the hardware information in YAST, it is listed there and it is also working under Windows.
View 4 Replies View RelatedI have a Dell Vostro 1500 that has a Broadcom BCM4312 wireless card installed. I do not have access to a wired connection to the web so any thing I have to install is a download on my windows machine and then transfer that to the debian machine. I just finished installing Debian Squeeze but can not get my wireless card to scan for any networks. I found a tutorial at [URL] and followed the steps there. Finding all the dependances and installing them one by one (took me all day). My wireless card still will not scan for networks. After doing a 'sudo ifconfig eth1 up' it still will not scan for networks.
Output from ifconfig:
raygo75@RayGo-2:~$ sudo ifconfig
eth1
Link encap:Ethernet HWaddr 00:16:44:9b:e9:cc
inet6 addr: fe80::216:44ff:fe9b:e9cc/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:17 Base address:0xc000
lo
Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:28 errors:0 dropped:0 overruns:0 frame:0
TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1900 (1.8 KiB) TX bytes:1900 (1.8 KiB) .....
How do I get around this? It wants to get something from [URL] and I do not have internet access. It looks to me like it just wants to download the wl dirver, again, which I have done in the previous instructions I found. I am a retired UNIX (hp-unix) administrator so I know my way around the system.
I just joined this forum in hope of fixing my linksys wireless card, here is my problem. I have a old Compaq presario 1710sb laptop with a p1 32mb ram and a 2GB hard drive. I installed a Debian Lenny command line only install, I installed ndiswrapper from a etch .deb file I found on the internet but I can't find out how to get it working. I tried how tos on other sites but they didn't work, I need to get that card working before I can install a GUI.
View 14 Replies View RelatedI am pretty new to Linux still. I have a desktop I'm trying to set up as a Linux machine. I'm apparently running a testing version of squeeze (I was running lenny I thought too many updates?). Anyway, I've been trying various things all night to try to get my wireless card to work. The system tells me I have a Broadcom BCM4318. When I run dmesg I get this:
[ 496.640869] b43-phy0 ERROR: You must go to [URL] and download the latest firmware (version 4).
[ 619.374662] input: b43-phy0 as /class/input/input25
[ 619.410838] firmware: requesting b43/ucode5.fw
[ 619.416638] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
Over and over. When I head to the website, it tells me to run b43-fwcutter. I've tried installing that and it says it installs fine but nothing ever changes. Everything I've found says that should work so I can't really find any suggestions for what to do if it doesn't.
I just installed Debian after I became fed up with Ubuntu. I'm trying to get my wireless card to work so I can move my computer back to it's proper place. Right now I have to put it right next to the router so the Ethernet cable can reach. Anyways, I've had trouble with this card before, so I did a quick google search. I found this: [URL]. I followed the instructions, and the thing at the top of the panel shows a list of wireless networks. When I try to connect to mine, it asks me for authentication. When I give it authentication, it idles for a while before asking me again.
Here's some system information:
uname -a
Linux max-pc 2.6.32-5-amd64 #1 SMP Wed May 18 23:13:22 UTC 2011 x86_64 GNU/Linux
lsmod | grep rt2860sta
rt2860sta 454573 1
crc_ccitt 1323 1 rt2860sta .....
From what I recall, when I used Ubuntu it was called ra0. Could this have something to do with it?