I'm not able to configure my microfone. Audio works very well. HW it's OK, mic works well on windows. Recording WAVE 'foo.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Stereo
Plug PCM: Linear conversion PCM (S32_LE)
Its setup is:
stream : CAPTURE
access : RW_INTERLEAVED
format : S16_LE
subformat : STD
channels : 2
[code]...
Well, when I run alsaconf, it finds my 82801H and I go on to setting it up, it says it will run, but it doesnt run.
Quote:
Now ALSA is ready to use.
For adjustment of volumes, use your favorite mixer.
But my song don't work, ..... works, but no sound in that, and i have tried running alsamixer to raise the volume to the peak.
I have a vague idea that, this sound card has difficulty in linux but all I get is 3 year old patches for gutsy gibbon and fixes that are non-slackware so I dont have the files and what not.
I have been trying, but never seem to understand why it says it works when it doesnt work.
Oh turns out, from thinkwiki, [url]
Its AD1984 actually, and it didn't work on 2.6.24.2 mine is 2.6.29.2 .
I am having some problems getting the onboard sound card on my Intel DP45SG motherboard to work properly under openSuse 11.1. Yast appears to have detected the card as a 82801JI (ICH10 Family) HD Audio Controller, but I cannot get any sound out of the card at all.
I have tried to follow this thread, and have run the alsa-info script, the results of which are posted here. It appears to me that the codec that is listed in the alsa script, which is the IDT 92HD73E1X5, is not the same as that which is listed on Intel's site for this board, which is the IDT 92HD73E codec. Can anyone help me out with regards to getting this going? Additional info below:
[Code]...
I was reading this article on how to fix the sound in Ubuntu 9.10 after upgrading from 9.04 [URL] and when I open GNOME ALSA Mixer, nothing shows up (I have included a picture). I typed in:
[Code]...
I've these intel 82801i, but my mic doesn't work, for skype etc.
If I compile alsa alsa-driver-1.0.9rc4a
Code:
gives:
Code:
Code:
I have a small audio problem: the Audio that exists from the back of my PC is working like a charm, but the one that cames out from the Frontal output doesn't work at all. It works well on OpenSuse 11.2, but it's not working on opensuse 11.3.
View 9 Replies View Relatedi just upgraded from Skype 2.0.0.72 to 2.1.047. Now my microphone isn't working anymore and i cannot select it in the skype options. From now on i can only select the PulseAudio server ..
So i have read some howtos for PulseAudio. They say i should starte PulseAudio Volume Control. ok.. Now i should go to the tab "Recording". This tab doesnt exist on my pc. I upgraded to the latest version of this volume control. It still doesnt exist.
I am using OpenSuse 11.0 with KDE4.3
Here are some screenshots:
[URL]
PS: My mic is still working with applications, that dont use pulseaudio.
I am using open -suse 11.1 .During start up I am getting notification such that,The audio playback device HDA intel (ALC888 Analog) does not work falling back to default.
View 2 Replies View RelatedI have an issue with my Sound on OS 11.2.It is correctly recognized under hardware and the driver seems to start properly as well when I do rcalsasound start.But under Control Center / Sound Preference there is no audio hardware listed (and hene no sound playing)
View 3 Replies View RelatedI have an HP Pavilion dv5 and Opensuse 11 with dual boot (windows and linux).. When I try to disable the sound using the hardware switch, it does, but when I try to reenable it it doesn't work.. it shows the same image that I get when I try to disable the sound.. The only way to reactivate using switches is to press vol +.. I have the lastest kernel and the lastest BIOS upgrade.
View 5 Replies View RelatedLets get straight to the point. im using Karmic, and as said by the title my audio card is not detected. lspci -v gives the following:
Code:
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
Subsystem: ASUSTeK Computer Inc. Device 1763
[code]....
I'm trying to extract files off of an audio CD using the program that came with Ubuntu. In the preferences I set the format to FLAC but when it's done and I open up the file manager, all the files are mp3. When I try to play the file with Songbird it tells me it can't read the codec. What's going on? I've extracted the music off of CDs before.
View 6 Replies View Relatedyou have an onboard soundcard that you have or may not have disabled in the BIOS, and you intend to use headphones with a USB sound card with headphone and microphone jacks (or no mic jack, it doesn't matter), but you notice that the headphones are detected. Alsamixer provides an interface to control the volume, etc etc, but still the headphones do not work..In my case, the module snd_hda_intel was being loaded for my onboard soundcard that I had disabled in the BIOS before booting the computer for the first time, and even though I tried to "activate" the USB headset in alsamixer, I still couldn't get the headset to work.
Solution as a trial: Open a terminal, and look to the code section for what you need to type.A big missing key to my puzzle is how to simply restart and/or reload a module so that it isn't necessary to unplug and plug back in the USB device. Can't I just re-discover the USB devices? (or other such hardware, such as a PCI card, or otherwise inaccessible component?)
whenever i oped an audio program, it doesn't work. for example in ardour it says, "JACK is running as another user".I think this is the problem for most of them.I searched for JACK and found a folder and it says the user's name is root.
View 1 Replies View RelatedFollowing instructions here: [URL] However, when I hit test in the audio settings I get an error saying it doesn't work. And when I try to load the installer exe I get the following error:
View 3 Replies View Relatedhappened and now half of the speakers plug is stuck in the back of my PC. cant get it out, because it's very deep. i decided to use the front jack for sound but it wont work.already tried alsa mixer and upgraded my kernel. i think the problem is that i need to somehow kill the jack in the back of PC because its still alive and sending signals to that half-dead jack
View 2 Replies View RelatedI've seen this problem on dozens of different forums but I haven't found anybody with my specific problem or a solution that has worked. I have an nVidia GeForce 8400GS which I just installed in my Debian box and I can't get the HDMI audio to work. Kernel version is 2.6.32-5-amd64, nvidia driver version is 260.19.36, alsa version is 1.0.21. Output of lsmod shows that nvidia module is loaded. Output of aplay -l code...
I feel like I've looked everywhere on the internet for a solution to this and I just can't find one. It seems that everybody is able to see their nVidia audio device using aplay -l and then the solution goes from there.
I'm using 64bit Ubuntu 9.10 and my sound card is not working. I'v tried to install oss drivers, but there is no effect.
View 1 Replies View RelatedWorks fine when I have the laptop plugged into the mains and will happily switch from 3.5mm to speakers and back again.
But for some reason, when the laptop is on battery I don't get any sound and all, from the 3.5mm or the speakers.
Samsung Q430 laptop
Ubuntu 10.10 x64 (fully up-to-date)
After the last updates (in which there was also the 2.6.35.28 kernel) my audio isn't working anymore. When i open an audio file, it goes foreward with steps like 5 secondos and i can't listen nothing. Videos i can see, but with no audio, and ..... videos go at like 2x speed (and also here no audio). I tried booting with the 2.6.35.27 kernel, but doesn't change anything.
View 1 Replies View Relatednow half of the speakers plug is stuck in the back of my PC. cant get it out, because it's very deep. i decided to use the front jack for sound but it wont work.already tried alsa mixer and upgraded my kernel.i think the problem is that i need to somehow kill the jack in the back of PC because its still alive and sending signals to that half-dead jack
View 1 Replies View RelatedI'm running Ubuntu 10.10 with an EVGA nForce 730i Intel mobo with onboard HDMI. Video output works. Audio output does not. I'm trying to output both to a Samsung HDTV.
I tried booting to a bootable drive with Ubuntu 11.04, and no audio.
I've essentially tried everything in every other thread. I'm using alsa mixer, I've muted S/PDIF, my settings all have HDMI output selected.
sudo modprobe snd-hda-codec-nvhdmi results in:
Code:
aplay -l results in:
Code:
aplay -L results in:
Code:
Also tried aplay -D to play a .wav, and heard no sound, but also encountered no errors.
Okay, when I load epsxe it loads just fine and I got it playing playstation games BUT the audio doesn't work. I have this issue with Basilisk II and it never got solved. When I load the epsxe executable I get
Quote:
I recently installed Ubuntu on my HP Pavilion dv4-2012br and am really enjoying it, except that it is conflicting with my sound card. The only way I can hear some sound is going into System> Preferences> Sound> Output and selecting "Internal analog stereo audio" which makes the sound hollow and not at all pleasant to listen to music. When I mark "RS880 audio device [Radeon HD 4200] Digital Stereo (HDMI)" the sound is not played.
I followed step by step these instructions: [URL] yet the only way to run the audio through the "Internal analog stereo audio. "
Just adding: I used the "Install with Synaptic Package Manager" way to do it. And i'm using a desktop version of Ubuntu.
Here are some screenshots:
[URL]
Wine in F12 (we no longer have the i386 build, only the x86_64 build available in x86_64 systems as in F11) winecfg crashes when trying to configure any audio controller and one is installed? I remember seeing this very same behaviour happen in Fedora 11 when using the x86_64 build, but the i386 did not have this problem. As soon as you click the Audio tab and click OK to the dialog warning that there is no "Audio driver slected", Wine enters into an infinte loop trying to start the debugger.
When I have time, I'll report this to the Bugzilla, as I do not believe the x86_64 package of Wine to be a true x86_64 binary (as older releases), but the 32-bit Wine only wrapped in a Fedora x86_64 package (then again, I maight be wrong, and indeed this package is 64-bit capable, which would mean it could run 64-bit native Windows executables), at any rate, in its current state, not only does winecfg crashes when trying to poll (I think) the sound devices, but if one of the controllers is installed, also trying to run an application that has sound (a game or multimedia program) it will cause the same effect (or simply not have sound at all).
I have the usual problem of "My sound is not working". I have a few images and my output from:
Code:
lspci
Code:
lspci -v
and
Code:
aplay -l
I can't really do anything with the speaker as it is hidden in the case.
I need to either force a redetection of my hardware or get the system to use the specific piece of hardware it is no longer using.
Details
Fedora 12
NVidia chipset/audio controller
Modprobe details of device "nVidia Corporation MCP79 High Definition Audio"
Tried installing kudzu but it does not install....
I am new to Linux and ran into a problem with no sound after a fresh install of Debian 6.0.
Here is what I get from my I/Os. (yes speakers are on, plugged in and all volume controls have been toggled and tweaked in every which way.)
Code:
Yamaha 754 is not working with alsa and working with OSS Whats the problem
[Code]....
I'm still working on ubuntu 9.10 with an acer aspire 1810tz. To use my microphone I found out that I have to change my microphone settings because it's mono and the default setting is thinking it's stereo: With the Volume Controller I setup one chancel to 5 and the other to 90 and the mic is working fine. Starting Skype and using it I see that the setting is reducing the volume for the mic below 20, so nobody can hear me. I tried closing first Volume Controller and then starting Skype, no matter the volume of the mic is reduced. How do I stop this behavior?
View 2 Replies View Related