I've up until recently been using Mint on my n210, but as I really liked the look of openSUSE (Gnome) I have changed to 11.3. So far I love the distro, but I am having a little issue - some fn key combinations aren't working (brightness in particular). When in Mint I was able to install a couple of programs made by Voria (from Linux On My Samsung), is there such a program for openSUSE?
View 3 Replies
I bought this netbook yesterday & thought of installing ubuntu netbook 10.10 on it.
I booted with windows & started the install using WUBI.
The wubi setup was started but then after copying files it told that some error occurred.
I though that I will deal with it later and left the wubi installed.
Now, when I rebooted after sometime, I am thrown to the code...
My netbook also has Hyperspace installed that comes with netbook. I provided that in case it is caused because of that.
Now what do I do? I didnt do anything wrong and still ubuntu messed up my system
I can not configure a driver for Linux SUSE for this video cameras All information below was written for this camera. This camera should work as a web camera (at least it worked well under windovs)
[Code]...
Have been successfully using a SCX-4824FN MFP for the past 2 years on Opensuse, trouble-free. Now, it no longer prints and am guessing it may have something to do with a recent Opensuse update? Error message states 'cannot create image', which I understand suggests Ghostscript problem, but Ghostscript is loaded and works fine with other HP printers attached to same PC (other forums also suggest Ghostscript may need installing).
Have downgraded to earlier version of Ghostscript but no joy.
I already noticed that others had similar problems with other Samsung scanner / printers. I could not find any solution in any threads (other than going back to 11.2 or buying a printer from a different vendor), so I'll ask again here: I'm running openSuse 11.3 on a 64 bit system.
Here's some error log output from CUPS:
E [20/Mar/2011:15:22:35 +0100] [Job 62] Failed to load the PPM image
E [20/Mar/2011:15:22:35 +0100] [Job 62] Job stopped due to filter errors; please consult the error_log file for details.
D [20/Mar/2011:15:22:35 +0100] [Job 62] The following messages were recorded from 15:22:34 to 15:22:35
[code].....
I am trying to install a driver for my scx4200. Ubuntu found this driver automatically but openSUSE 11.4 (64bit) does not. I have the manufacturers Cd with a Linux folder on it but if I run "autorun" in terminal it says permission denied. I have copied the files to a new folder on my hard drive but do not know how to run "autorun" in terminal with sudo. I switched to openSUSE because Ubuntu 11.4 kept freezing. SUSE does seem much better.
View 1 Replies View RelatedI'm on a T42 laptop with a Samsung ML-1740 attached on my USB port. I installed the printer with the tool and everything seemingly went okay. Won't print, tho. I read somewhere on fedora's pages (prob the forum) that someone had a similar prob and it was a matter of loading foomatic, whatever that was, then retrying the load. It worked for them. Anyone aware of this?? Or is this a simple fix? I used the recommended driver for ML-1740 listed in the GUI.I have to reboot, I'll try to get a printout from troubleshooting.
View 4 Replies View RelatedI have brought my son a samsung n150 mini laptop. It has a "realtek rtl8192e wireless lan 802.11n pci-e nic" card fitted to it. I have tried downloading the drivers from samsung and realtek, but still can't get it to connect. It see's the local connections but when i try to connect it says it is unable to.
View 1 Replies View RelatedThe situation:At my workplace there is a shared printer installed in WINDOWS. It's installed also in my windows system(WINDOWS 7 ULTIMATE version 7600). It's working very well. From windows I shared it to have the option for printing from openSuSE 11.3. In Samba I can see the other colleagues connected to the same workplace network. I shared also the printer with Samba.I can see it.
The problem :The printer doesn't work.I can't find a opensuSE11.3 driver for it (Samsung CLX 3170 FN).The question 1:Is it really need a properly driver for it if it installed in windows? The question 2:How can I make printing from openSuSE11.3 with the shared installed in windows server printer? Steps done:in MS Win system I shared ,I noted the WORKGROUP,the PC name and the IP for the printer. //ALso I know the domain and my IP.well done in resolv.conf,in fact I have internet connection from openSuSE 11.3,no problem,e-mail/evolution and kmail are working very well,configured both for the workplace). Now in openSuSE what should I do? I need some advices/right steps) about configuring this printer USING few ways(Samba,Printer config from YAST etc) because I am thinking somehow I did something wrong. When I make print test page the printer make the noise is preparing but nothing is happening. I believe that maybe the driver missing is the problem. BUT ONCE AGAIN,it's installed in my PC in Windows system,/I have dual boot system/GRUB MANAGER/openSuSE and Windows 7 Ultimate 7 7600. Can I work with the printer via internet/network //Samba/CUPS/etc,etc with localhost /IP,or other way if I DON'T have a driver for openSuSE
[Code]...
I bought a samsung r525 quad core laptop with 6630 1gb video. I returned my samsun I got last week that was a amd dual core with 5370 512 video....
the old laptop performed better then this new one...
The windows score for graphics is 4.0 (old one was 5.1) I checked in display adaptors and it says i have 4250 running ... i also have 6630 on that list .....
what i tryed doing
1- ati drivers searched to see if i can enable the 6630
2- disabled the 4250 in hopes the 6630 would take over
3- ran programs like counter strike / civ 5 and it did not perform as well as the older dual core samsung...
What gives .... the geeksquad and sales staff could not explain this...
Suse 11.3 with KDE 4.4.4
I have a Samsung Galaxy Apollo android phone but Suse won't recognize the phone to download apps. When I have a SD card in the phone it automounts it as "USB imaging interface" and the only option is "download photos with Digikam" and I'm unable to view it the file manager. how can I get the phone to be recognized? I'm using Suse, I still don't know about hardware etc.
I have a machine running 11.3 and I want to increase my storage capacity but am maxed out with 6 SATA hard drives already. Does openSUSE 11.3 see and write to drives 1 terabyte and above correctly?
I have been using WD Green drives in this machine up until now but see Samsung and Hatachi drives at really good prices. Are these drives reliable? How is warranty support?
I have a Macbook Pro 2,66 Ghz (June 2009) and i also use a Samsung T240HD-Screen. The Mac has a MiniDisplayport und i use a converter to HDMI. I don't get a signal on the external screen. It is displayed in the X-Server-Settings and i can configure it (Resolution, Twinview, Position and so on) but when i go to the GPU-Section all the Information in the section of den T240HD-screen is "unknown". Nvidia Driver Version: 190.53
View 2 Replies View Relatedyesterday I upgrade my opensuse 11.2 to 11.3 with zypper dup. Today I try to print something but printer doesn't react for page nor test page. On 11.2 it works perfectly. I have samsung ml 1640 connected directly to PC via usb.
output from cups:
Description:OpenBlackBox v mojom rume
Location:Moj rum
Driver:Samsung ML-1640 Series (grayscale, 2-sided printing)
Connection:usb://Samsung/ML-1640%20Series
Defaults:job-sheets=none, none media=iso_a4_210x297mm sides=one-sided
My phone won't connect when adding via a usb cable. The device is seen, but gives the following line in dmesg:
Code:
[ 982.151966] usb 2-5.4: new full speed USB device using ehci_hcd and address 6
[ 982.239668] usb 2-5.4: New USB device found, idVendor=05c6, idProduct=1000
[code].....
I just finish installing 11.3. Everything works perfectly expect few issues with my display setting. I've installed SUSE on my laptop Acer Aspire 5920G and I got Samsng 226BW as my second display. How can I change the resolution of my Samsung display to 1680*1050? currently set as 1024*768 and I can't change it. Do I need to update my NVIDIA driver? if so how can I do that? finally, If I get this fixed how can I set my Samsung to be the main display?
View 1 Replies View RelatedI needed to load Linux on a Samsung Q1Ex for a project I'm contracting on, and could not for the life of me get anything to run. Turns out that the video card is a chrome relative, and for some reason, almost every distro out there (I usually use debian for this sort of project - ie, no money, but use SLES at my day job) failed to even get to textmode console. Trying several distros, I finally put it out there and used OpenSuse and voila!, vga was working. After that, I got X running, and many hours later had the mouse working. The key to this device is Windows. I ended up parsing through the registry looking for "touch" and found that the software in use on Windows is eGalaxTouch. A quick google brought up their site where I found several Linux drivers. I used the beta mode drivers to get the mouse working. Here is a more detailed breakdown.
Use OpenSuse 11.3 (I used the full blown disc - its is the only distro I could get to boot correctly as the others all used OpenChrome, while OpenSuse seems to use fbdev - note here that installing the unichrome drivers will actually break X and cause you to have to reboot to get away from the mess on the screen). Use eGalaxyTouch drivers. The pdf's included in the download have step-by-step instructions but the big pieces are the setup.sh script and the serio_raw steps (note if you perform a 'hwinfo --bios | more' you can figure out which /dev/input/event* you're using - for me it was event1 and serio4). Note also to choose PS/2 when executing the setup.sh script provided in their download. eGalax_eMPIA Technology Inc. TouchKit Linux Driver Here is my xorg.conf now:
Section "ServerLayout"
InputDevice "EETI" "SendCoreEvents"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
[Code]....
On the video, just stay with the fbdev and you should be good. So far, I've had KDE, Gnome, TWM all running; and now have my EFL apps running! Woohoo! Next piece of the puzzle is to verify sound, but on the face of it, looks like the system recognized it off the bat. And of course one other note. 11.3 is going to make me a convert!
I like ubuntu alright, but prefer Debian overall. Before I reinstall Debian I was wondering if during the install if the latest release would automatically recognize the Samsung ML 1665 as the latest ubuntu release did. If not, how does one get the printer installed.
View 3 Replies View RelatedOn Printer installation, the ML-1740 printer is recognized, and the driver for the ML 1750 is recommended. When either test page or other page is printed, job shows in queue, then shows as completed, never gets printed. Cables look fine, Printer worked fine with F11.
View 8 Replies View RelatedI've just gotmy new phone a SamsungGT-S5230! My problem is:I can't transfer any file from my ubuntu desktop over to my phone. On the CD it came with there is only a windows software called "PC Studio" and Windows drivers. As I plug in the phone via USB to the PC it offers 3 options: PC Studio, Media Storage, Background Storage. If I pick one of the first 2 options my phone says it is connected, and charges via USB. The third option says "Please Insert a MicroSD card". (I don't have such at home). Ubuntu can't see my phone, none of the options seem to work. Maybe I should buy a MicroSD card? Or is there a workaround for the windows software to run ubder Linux? I tried to install t with WINE, but it froze during the installation.
View 4 Replies View RelatedI am trying to install Ubuntu 9.10 on a Samsung Q1 Tablet PC but it reaches a point when the screen becomes smokey and then after a few seconds gets black, forcing me to abort.
View 3 Replies View RelatedI have just purchased the Samsung N150 net-book. The reason for purchasing was so I could watch movies, listen to music and browse on the go. It came with windows 7 starter and a load of pre installed Samsung crap. I was wondering whether Ubuntu would be a better choice for me since I only really want, Chrome, VLC, Spotify, MSN and Dev++ compiler.
I am very computer literate doing programming at Uni, but have not used Linux before. Also there's loads of Samsung software for extending battery life or something. Will I be able to install that on Ubuntu or not?
Tried installing all the Samsung ML-**** from the list. PS Getting really tired of booting XP every time I want to print something.
View 3 Replies View RelatedI bought a new printer from SAMSUNG ML2245 Model. In my system (fedora12), I could not print anything. Then I found that this model samsung ML2245 does not exist in the list box. And I tried to use generic printer, that is also failed. How to install the driver for this model?
View 1 Replies View RelatedHow can use my printer in my linux? My printer is samsung clp-510.
View 3 Replies View RelatedI have a 650Gb HDD usb drive that I wish to use with ubuntu 10.04LTS aswell as on a WINXP system. HDD is clean. My ubuntu system has a /home partition formatted to EXT3, but as I use IFDRIVE to read this partition from windows, it needs to be set to have inode of 128 eg (mkfs.ext3 /dev/sdb1 -i 128)
my way of thinking is I need to partition the drive, format the drive to EXT3 making sure that is set inode to 128 How do is the best way to do this?
Then I need to get ubuntu to talk to this drive when I plug it in How do I do this?
How do I install my Samsung SCX-4623FW/XAA multipurpose B&W Laser printer in Ubuntu Linux via USB cord on my 5-6 year old Dell desktop?
I have downloaded three files from Samsung.
/home/chuck/Downloads/UnifiedLinuxDriver_0.95.tar.gz
/home/chuck/Downloads/Smartpanel_0.95.tar.gz
/home/chuck/Downloads/PSU_0.95.tar.gz
I had an ubuntu 11.10 installation that was no longer supported and was low on disk space, so I bought a new disk and installed debian wheezy on it and made it the boot disk.
The machine had/has a samsung e2020 monitor, and ubuntu and the new debian install both recognized it as 1600x900 resolution. I ran the proprietary nvidia driver with ubuntu but did nothing at all with the debian ... it just worked.
The power supply on the machine conked out and I took it ro be replaced and dug out an old, old machine to use while the newer one was gone. Debian would not install on it. But ubuntu 11.10 did, but displayed at 1024x768 on the samsung which it recognized as a 'VGA'. It was slow, but it worked. When the newer machine came back I reinstalled it ... but its debian 7.6, which used to know the samsung at 1600x900 resolution, now runs it at 1024x768, just as the old box had!
It must be some change made to some firmware in the samsung itself? It's not very pleasant.
I've tried to install the nvidia driver , but no luck there. I see now that debian uses something called 'nouveau' to run the proprietary nvidia chip, and I'm all for that ... but it used to be able to run it at 1600x900 and now it's forgotten how.
Here they are ...
Code: Select alljfl@wsdeb:~$ xrandr
Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096
VGA-1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm
1024x768 60.0*
800x600 60.3 56.2
848x480 60.0
640x480 59.9
[Code] ....
So I've gotten lucky, haven't I? I don't know if the display will still be ok when I restart ... so I'll save a copy of the above and try to script it, if I must, on reboot/relogin.
I just bought a Samsung 850 Pro 250GB SSD drive and have since then found out that Linux has/had a faulty implementation of queued trim (which is a synonym for NCQ I think). I'm using kernel 4.1.0 (the default selected by the Debian 8.1 installer) and I've read that Samsung drives are blacklisted for queued trim by the recent kernels. However, the output of dmesg contains the following lines, with and without TRIM enabled for the drive (i.e. with or without the "discard" option in fstab for the drive):
Code: Select all[ 1.012287] ata6.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.013438] ata5.00: failed to get NCQ Send/Recv Log Emask 0x1
[ 1.013440] ata5.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[ 1.015037] ata5.00: failed to get NCQ Send/Recv Log Emask 0x1
Since the depth is not 1 but rather 31, it looks like NCQ is enabled. I've disabled TRIM on the drive for now, and whether it's safe to enable TRIM or not.
I have a Samsung ML 2510 USB connected to an F13 based system. The printer is registered as the default printer. A test print gives the printer what I call a wake up call and then never prints. Win XP dual boot prints fine.
View 2 Replies View Related
