OpenSUSE Hardware :: 11.3 Breaks Samsung SCX 4300 Printing?
Mar 20, 2011
I already noticed that others had similar problems with other Samsung scanner / printers. I could not find any solution in any threads (other than going back to 11.2 or buying a printer from a different vendor), so I'll ask again here: I'm running openSuse 11.3 on a 64 bit system.
Here's some error log output from CUPS:
E [20/Mar/2011:15:22:35 +0100] [Job 62] Failed to load the PPM image
E [20/Mar/2011:15:22:35 +0100] [Job 62] Job stopped due to filter errors; please consult the error_log file for details.
D [20/Mar/2011:15:22:35 +0100] [Job 62] The following messages were recorded from 15:22:34 to 15:22:35
[code].....
View 1 Replies
ADVERTISEMENT
Nov 1, 2009
On Printer installation, the ML-1740 printer is recognized, and the driver for the ML 1750 is recommended. When either test page or other page is printed, job shows in queue, then shows as completed, never gets printed. Cables look fine, Printer worked fine with F11.
View 8 Replies
View Related
Jul 22, 2010
I noticed that after applying updates to my ubuntu 10.4 desktop my printer was not working. I discovered that cups was no longer running and I was unable to get it to start. After re-installing cups using the below command everything is now working. This is the 2nd time I've had to re-install cups after patching.
Quote:
sudo apt-get install --reinstall cups
This appears to be a critical bug: #554172
View 2 Replies
View Related
Jul 4, 2011
I upgraded from 10.04 and I like 11.04 alot. I had a slight problem with wireless but got that ironed out. My LIDE 210 scanner now works too. But my Samsung ml-2250 printer is not working properly now when it was in 10.04.
If I print out any type of document it runs through all the paper in the tray. I printed out a test page and the actual test page had a bunch of characters in one line at the top, then one line below that it said "you are using the wrong driver".
I've reloaded the splix in synaptic twice for samsung drivers but still the same results. I have no idea what 10.04 used for drivers. Also, I can stumble my way around Ubuntu in the terminal, but best to just think of me as a noob.
View 2 Replies
View Related
Dec 9, 2010
Using Fedora 14. Printer usb connected and recognised with correct driver: Foomatic/PXL mono (Recomended). Will not print test page or anything else. Nothing seen in print queue.Iinitially choked by SElinux (since deleted). Still not working.
View 2 Replies
View Related
Jan 31, 2010
I have an averatec laptop 4300series. I've installed linux suse-11 on it but problem with display adapter card. I couldn't find on Averatec site any appropriate display adaptor card for linux.
View 1 Replies
View Related
Jan 1, 2010
I'm thinking of setting up an old desktop (Dell Dimension 4300/512mb RAM/20g&80g hdd) as a media/file server and using Slackware 13 for it. I'm completely new to doing anything server-wise,it of background: I'm running current versions of Zenwalk and Vector on two different laptops, with the Zenwalk one multi-booting Vista and Ubuntu. The desktop in question is running XP and Zenwalk. I have DSL hooked up to a Linksys WRT (running dd-wrt firmware) for network. I'm not a noob, just not in my comfort zone. My goal is, in addition to setting up the server, to get more hands under the hood (so to speak) on improving my linux skills. It was a toss up between Slack and CentOS, and being very familiar with Slack-based systems, I'm going that route.
View 4 Replies
View Related
Jun 28, 2011
I am running OpenSUSE 11.4 on my laptop and I decided to try out the Gnome 3 shell. I really like the design and I like the way it functions so I would like to keep using it, but it seems as though every time I install a new application or package it breaks Gnome 3. This is really frustrating because when I then try to log in it just gives me that cryptic error message that im sure you all have heard about "Oh No! Something went wrong!" or something like that and then it tells me to log out.
I know a fair bit about linux in general, but im no expert by any stretch of the imagination (my experiences have been with Ubuntu, Xubuntu, Linux Mint, and some older distros) so im only used to the Apt-get package manager and I find zypper to not be very understandable. So I don't know if im breaking Gnome 3 every time I install something because of some dependencies not getting installed. My laptop is running a Intel cure 2 duo processor and an Intel mobile graphics chipset (which runs gnome 3 fine normally).
View 6 Replies
View Related
Mar 2, 2009
I just got a set of updates from Xorg11 (Index of /repositories/X11:/XOrg/openSUSE_11.1/i586) repository and now, my X doesn't come up. During update, zypper complained about xorg-x11-libxcb and it didn't get updated. On further investigation I noticed that libxcb-xlib.so.0.0.0 is missing in the new package (version 7.4-4.2. The one currently installed in 7.4-1.24).
View 9 Replies
View Related
Apr 22, 2011
That was released in October 2008, superseded in March 2009, and the current release is 1.4.3. It also doesn't work together with Python, but that's a more esoteric issue. Both of them are too clever by half, and the combination breaks the library loading mechanism. That's an old issue, with an old fix - though I haven't yet checked my rebuild, so there may be more than one problem.
View 1 Replies
View Related
Mar 16, 2011
I'm a regular OpenSuse user, but recently I had to download Windows7 on my computer for work. Everything was fine for a while, but now when I switch to windows, the wireless doesn't work sometimes (sometimes it works just fine). When this happens wireless is broken on the Linux side as well. The only way I know to fix it is to hard wire the laptop when booted into windows, and then everything is back to normal. It's really starting to tick me off and I have no idea what may be causing it. I didn't even know the two partitions can effect each other.
View 9 Replies
View Related
Feb 8, 2010
I've just upgraded my main file server from 10.3 to 11.1 by DVD (I did *not* have a chance to do a zypper up after, so it's the base 11.1 install), and in upgrading my Samba from 3.0.23b to 3.2.4, I seem to have broken winbind resolution of group names. wbinfo -g shows all the right group name entries, and getent group shows that they map to the proper GID numbers... it's just that ls isn't seeing them: I get domain usernames, but the group column is 5 digit numeric GIDs in my defined range. I infer that something broke PAM, but I'm not enough of a PAM jockey to know what. I don't have a pam.d/winbind, but I'm not clear that I'm supposed to. I see that the four pam.d/common-* files were touched, but their contents are the same as the older ones I have.
View 6 Replies
View Related
Sep 9, 2010
I've up until recently been using Mint on my n210, but as I really liked the look of openSUSE (Gnome) I have changed to 11.3. So far I love the distro, but I am having a little issue - some fn key combinations aren't working (brightness in particular). When in Mint I was able to install a couple of programs made by Voria (from Linux On My Samsung), is there such a program for openSUSE?
View 3 Replies
View Related
Aug 11, 2011
My son wants to install Wintendos so that he can play starcraft 2 on my new comp. But it doesn't seem to work. Every time I try to install it the install breaks down with an error message like, no boot disc/media can be found. (This is after the install has started, a couple of minutes in.) I suspect that Microsoft doesn't support usb 3.0 in their native distribution of win7, not sure though. And that my comp only has usb 3 ports. How do I check what kind of hardware my comp is packing, specially USB ports.
View 3 Replies
View Related
Dec 15, 2010
I got a problem with flash player. Atm I'm using chrome. Flash version 10.1.102, chrome version 6.0.472 So, my problem is that after a long while of having the browser open (any), flash player stops working properly (it's hard to describe but in ..... for example, the image and sound freeze for 5 seconds, in the next second everything happens at once, freezes 5 seconds again, shows all that frozen time in fast forward again, etc). This happens every a few hours of not closing the player's plugin I restart flash with the chrome task manager, reload the page, and it works properly again. I tried using firefox but I have the same problem (except I cant restart the flash plugin without restarting the browser).
View 2 Replies
View Related
Jul 20, 2010
Ever since installing 11.3, my Samsung CLX-3175 laser mfp no longer prints. It worked fine under 11.2 using the Samsung proprietary unified driver. That driver no longer seems to work under 11.3. The print job never leaves the queue and the printer must be rebooted (it is a networked printer) to be recognized by the operating system after deleting the job. Here is the relevant error printout from the cups error log from an attempt to print the test printer job:
[Code]....
View 9 Replies
View Related
May 30, 2011
I have recently upgraded to 11.4 and also had to renew an AP (HP ProCurve 10ag). This was several years old but replaced an identical model which had been working well until recently. I thought it would be appropriate to flash newer firmware as the device four releases behind the times. The access point serves partner's XP laptop and my openSUSE 11.4 laptop and after flashing the firmware both machines would make a connection and then break and remake, to the extent that the openSUSE machine became unusable. I thought it was an encryption problem and spent hours changing the AP and Client setups to no avail
After reading a thread here I checked out dmesg and this is what I found:-
[78.639247] wlan0: authenticate with 00:1d:b3:4b:ae:14 (try 1)
[78.640804] wlan0: authenticated
[78.642507] wlan0: associate with 00:1d:b3:4b:ae:14 (try 1)
[78.651195] wlan0: RX AssocResp from 00:1d:b3:4b:ae:14 (capab=0x411 status=0 aid=1)
[78.651200] wlan0: associated
[78.652222] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[78.652283] cfg80211: Calling CRDA for country: DE
[78.674378] cfg80211: Regulatory domain changed to country: DE .....
This went on and on.
View 7 Replies
View Related
Feb 10, 2010
I can not configure a driver for Linux SUSE for this video cameras All information below was written for this camera. This camera should work as a web camera (at least it worked well under windovs)
[Code]...
View 1 Replies
View Related
Dec 8, 2010
Have been successfully using a SCX-4824FN MFP for the past 2 years on Opensuse, trouble-free. Now, it no longer prints and am guessing it may have something to do with a recent Opensuse update? Error message states 'cannot create image', which I understand suggests Ghostscript problem, but Ghostscript is loaded and works fine with other HP printers attached to same PC (other forums also suggest Ghostscript may need installing).
Have downgraded to earlier version of Ghostscript but no joy.
View 6 Replies
View Related
May 23, 2011
I am trying to install a driver for my scx4200. Ubuntu found this driver automatically but openSUSE 11.4 (64bit) does not. I have the manufacturers Cd with a Linux folder on it but if I run "autorun" in terminal it says permission denied. I have copied the files to a new folder on my hard drive but do not know how to run "autorun" in terminal with sudo. I switched to openSUSE because Ubuntu 11.4 kept freezing. SUSE does seem much better.
View 1 Replies
View Related
Jan 5, 2010
I'm on a T42 laptop with a Samsung ML-1740 attached on my USB port. I installed the printer with the tool and everything seemingly went okay. Won't print, tho. I read somewhere on fedora's pages (prob the forum) that someone had a similar prob and it was a matter of loading foomatic, whatever that was, then retrying the load. It worked for them. Anyone aware of this?? Or is this a simple fix? I used the recommended driver for ML-1740 listed in the GUI.I have to reboot, I'll try to get a printout from troubleshooting.
View 4 Replies
View Related
Jul 19, 2011
I have brought my son a samsung n150 mini laptop. It has a "realtek rtl8192e wireless lan 802.11n pci-e nic" card fitted to it. I have tried downloading the drivers from samsung and realtek, but still can't get it to connect. It see's the local connections but when i try to connect it says it is unable to.
View 1 Replies
View Related
Aug 4, 2010
The situation:At my workplace there is a shared printer installed in WINDOWS. It's installed also in my windows system(WINDOWS 7 ULTIMATE version 7600). It's working very well. From windows I shared it to have the option for printing from openSuSE 11.3. In Samba I can see the other colleagues connected to the same workplace network. I shared also the printer with Samba.I can see it.
The problem :The printer doesn't work.I can't find a opensuSE11.3 driver for it (Samsung CLX 3170 FN).The question 1:Is it really need a properly driver for it if it installed in windows? The question 2:How can I make printing from openSuSE11.3 with the shared installed in windows server printer? Steps done:in MS Win system I shared ,I noted the WORKGROUP,the PC name and the IP for the printer. //ALso I know the domain and my IP.well done in resolv.conf,in fact I have internet connection from openSuSE 11.3,no problem,e-mail/evolution and kmail are working very well,configured both for the workplace). Now in openSuSE what should I do? I need some advices/right steps) about configuring this printer USING few ways(Samba,Printer config from YAST etc) because I am thinking somehow I did something wrong. When I make print test page the printer make the noise is preparing but nothing is happening. I believe that maybe the driver missing is the problem. BUT ONCE AGAIN,it's installed in my PC in Windows system,/I have dual boot system/GRUB MANAGER/openSuSE and Windows 7 Ultimate 7 7600. Can I work with the printer via internet/network //Samba/CUPS/etc,etc with localhost /IP,or other way if I DON'T have a driver for openSuSE
[Code]...
View 6 Replies
View Related
Jun 5, 2011
I bought a samsung r525 quad core laptop with 6630 1gb video. I returned my samsun I got last week that was a amd dual core with 5370 512 video....
the old laptop performed better then this new one...
The windows score for graphics is 4.0 (old one was 5.1) I checked in display adaptors and it says i have 4250 running ... i also have 6630 on that list .....
what i tryed doing
1- ati drivers searched to see if i can enable the 6630
2- disabled the 4250 in hopes the 6630 would take over
3- ran programs like counter strike / civ 5 and it did not perform as well as the older dual core samsung...
What gives .... the geeksquad and sales staff could not explain this...
View 1 Replies
View Related
Jun 25, 2011
Suse 11.3 with KDE 4.4.4
I have a Samsung Galaxy Apollo android phone but Suse won't recognize the phone to download apps. When I have a SD card in the phone it automounts it as "USB imaging interface" and the only option is "download photos with Digikam" and I'm unable to view it the file manager. how can I get the phone to be recognized? I'm using Suse, I still don't know about hardware etc.
View 9 Replies
View Related
Aug 28, 2011
I have a machine running 11.3 and I want to increase my storage capacity but am maxed out with 6 SATA hard drives already. Does openSUSE 11.3 see and write to drives 1 terabyte and above correctly?
I have been using WD Green drives in this machine up until now but see Samsung and Hatachi drives at really good prices. Are these drives reliable? How is warranty support?
View 9 Replies
View Related
Jul 28, 2010
We developed qt based application in linux. I wish to stop ejecting the paper after printing over.How to do it.
View 2 Replies
View Related
Feb 12, 2010
I have a Macbook Pro 2,66 Ghz (June 2009) and i also use a Samsung T240HD-Screen. The Mac has a MiniDisplayport und i use a converter to HDMI. I don't get a signal on the external screen. It is displayed in the X-Server-Settings and i can configure it (Resolution, Twinview, Position and so on) but when i go to the GPU-Section all the Information in the section of den T240HD-screen is "unknown". Nvidia Driver Version: 190.53
View 2 Replies
View Related
Jul 27, 2010
yesterday I upgrade my opensuse 11.2 to 11.3 with zypper dup. Today I try to print something but printer doesn't react for page nor test page. On 11.2 it works perfectly. I have samsung ml 1640 connected directly to PC via usb.
output from cups:
Description:OpenBlackBox v mojom rume
Location:Moj rum
Driver:Samsung ML-1640 Series (grayscale, 2-sided printing)
Connection:usb://Samsung/ML-1640%20Series
Defaults:job-sheets=none, none media=iso_a4_210x297mm sides=one-sided
View 3 Replies
View Related
Jul 7, 2011
My phone won't connect when adding via a usb cable. The device is seen, but gives the following line in dmesg:
Code:
[ 982.151966] usb 2-5.4: new full speed USB device using ehci_hcd and address 6
[ 982.239668] usb 2-5.4: New USB device found, idVendor=05c6, idProduct=1000
[code].....
View 3 Replies
View Related
