Networking :: PCI Network Card Not Detected As It
Aug 27, 2010
I added to my machine PC running debian and others, ubuntu, pc wireless card:,the same card I used it on other machine, it ran nice.On the other machine i have Ethernet Controller instead of Class ffff.I installed the divers firmware-ralink and other realtek and network-manager, but nothing.on other machine, that was enough to run it correctly.and ifconfig dosn't give wlan0,iwconfig did't give characteristic of wlan0.does this mean that the bios didn't recognize it as a network card
View 3 Replies
ADVERTISEMENT
Apr 4, 2010
I have bought a new laptop with W7 installed. And I installed dual boot with Ubuntu 9.10 on it.I tried to connect my laptop to Internet by Ethernet port. It works with W7, but Ubuntu doesn't detect my Network card .After some research on Internet, I suppose that it's a problem of drivers for this card.Here some parameters I could get :
>ifconfig :
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
[code]...
View 4 Replies
View Related
Jun 16, 2010
I'm in serious need of some help. The network adapter on the motherboard of my main machine apparently failed about noon today. This machine serves as the firewall and router for my home office LAN, and so it has two network adapters, the second being a PCI card installed in the only PCI slot of the mobo. The mobo's adapter served the WAN while the PCI card serves the LAN.Since the mobo has only one PCI slot, none of the other PCI cards I have on hand could be used. Instead, I pulled an unused PCI-e dialup modem card from the machine, and bought a PCI express gigabit card to put in its place.
The problem is that the machine (running Hardy 8.04.4 LTS) does not recognize the new card at all. Running lspci shows only the old PCI card that serves the LAN. Similarly, running "sudo lshw" shows only the old PCI card together with a virtual adapter that's part of my VirtualBox installation on that system.I then dual-booted into Vista Home and attempted to install the new card there, using the CD that came with it. Vista detected the card and asked for the disk, but then was unable to find any drivers on the disk!The box says the card is from Star Tech, and the instruction sheet says its model is ST1000SPEX.If anyone can point me to the correct module to add to the startup list and/or remove from the blacklist, that may get me going again.
View 3 Replies
View Related
Aug 27, 2010
I have a Realtek gigabit onboard ethernet (RTL-8110SC/8169SC)It was working in 9.10.After upgrading to 10.04, the connection dropped to 10MB. Now, lspci -v shows the card, but Ubuntu no longer recognizes eth0!I have no connection on the machine. I've been digging around the forums, but can't seem to find what I need.
View 2 Replies
View Related
Mar 7, 2009
I have downloaded and installed Fedora 10.Now I am setting up the network and in the 'network configuration' it finds the wireless device (ralink) in the 'hardware' section of the configuration - I set this to eth0 (it originally set itself to wan0 and I still had the same problems, now it doesn't give me the option to put it back to wan0).Now I goto the devices tab and try to set up the device with eth0 - which it seems to find.But when I goto activate the device it tells me that eth0 cannot be found
View 2 Replies
View Related
May 20, 2010
My network cards were fine under Wubi Lynx. I decided to upgrade to Ubuntu Studio Lynx on its own partition, and the DVD install routine failed to detect the network card. Where do I go from here?***1 ) Machine Brand and Model (PC/Laptop):Acer 1410 (dual amd64 netbook, about a year old)***2) Network Interfaces
>lspci
01:00.0 Ethernet controller: Atheros Communications AR8131 Gigabit Ethernet (rev c0)
02:00.0 Network controller: Intel Corporation WiFi Link 1000 Series
[code]....
View 3 Replies
View Related
Nov 1, 2010
I have an Acer Laptop and I am trying to use Linux Redhat 5 on it but for some reason the NIC is not detected by Linux. It is a bit surprising to me that the same problem was seen in my desktop computer but after changing the NIC to a different slot the Linux OS detected the NIC and it is working fine but my laptop still has the same problem.
From troubleshooting point of view:
1. Installed Linux multiple times but it didn't work.
2. Tried to add the hardware (NIC) but it didn't work.
Note: The NIC was working fine when I first installed Linux but after sometime it didn't. The laptop is dual boot (Windows & Linux) when I boot via windows the NIC works fine but not with Linux.
NIC Details:
Device Type: Network Adapter
Manufacturer: Broadcom
Location: PCI bus 2, device 0, function 0
View 4 Replies
View Related
May 23, 2010
I have Onboard Realtek ethernet card (eth0) it worked fine but suddenly it stopped working when i see in yast it shows hwinfo not found. when i use hwinfo --netcard it gives realtek card name thats all. I went to yast >lan> edit> hardware and tried to add r8169 module but it was not accepting. previously created ifcfg-eth0 file is available but its not getting up.when i say ifup eth0 it say interface not found. the same messg is also available in /var/log/boot.msg.
View 4 Replies
View Related
Dec 9, 2009
i am testing the opensuse 11 installation on the Eee pc (Eee Box B202). My installation source is in the network drive but i can't seem to point it to this destination because the network card is not detected. This Eee pc is using a jmicron network card and i can't seem to find any related drivers on the net.
View 1 Replies
View Related
Jan 6, 2010
I've been using Slackware distribution for few years now, Setup new system with Xen Server 5.5 and installed Slackware 13 on it, but network card is not detected and can't seem to make it work.
View 4 Replies
View Related
Mar 14, 2009
Wireless card detected but cannot connect to a wireless network
I have install it suse 11, and everything went well until the wireless thing is not working, my card is Broadcom BCM4318, I see my card on the network settings but I cannot configure the card, and also I cannot connect to a wireless network, can someone tell me what to do here, I am loosing my patient....
View 4 Replies
View Related
Jun 27, 2010
I have a dual boot with W'XP and RHEL 5. M/B is MSI.
In XP the LAN is detected but not in LINUX.
View 2 Replies
View Related
Apr 30, 2010
I have just upgraded from 9.10 to 10.04 and now my wireless card isn't being detected as far as I know. It was working perfectly in the previous version. At the moment I've physically put an ethernet cable straight to the router.
[code]...
View 9 Replies
View Related
Dec 3, 2010
I have brought a new DELL INSPIRON 1410. I installed ubuntu 10.04 but my ethernet card is not getting detected where as in windows 7 is working..
View 2 Replies
View Related
Jun 18, 2011
I bought a new TOSHIBA C660 - i5010 today and installed.Lucid Lynx 10.04 on it, but it has not detected my wirelessg broadcom 80211 (STA) driver debp interface.
View 1 Replies
View Related
Dec 17, 2010
I have just installed Fedora 14 on my desktop machine and have just discovered that it can't detect my WiFi card. The card is an Edimax EW-7711In which the makers say will run with Linux. I know that the card works fine with Ubuntu because my brother uses the same card in his Ubuntu machine but he is away until after Christmas so I don't know what he did to make it work other than I know he used ndiswrapper and the Windows drivers that were supplied with the card. I have looked for ndiswrapper in the Fedora repositories but it doesn't appear to be there.
View 14 Replies
View Related
Mar 1, 2010
im having some trouble connecting the wireless card to my wifi network, theres is a hint using the terminal
remora@remora-laptop:~$ sudo lshw -C network
[sudo] password for remora:
*-network DISABLED
description: Wireless interface
[code]....
View 6 Replies
View Related
Jun 13, 2009
I have a problem with Netgear Wireless WG311v3 card and it is not listed in "ifconfig -a". Network Manager does not see the Netgear card either, just eth0 the onboard wired NIC. Here is the result of lspci.
Code:
[root@mylinux ~]# lspci -nn
02:00.0 Ethernet controller [0200]: Attansic Technology Corp. Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller [1969:1026] (rev b0)
03:00.0 IDE interface [0101]: Marvell Technology Group Ltd. 88SE6101 single-port PATA133 interface [11ab:6101] (rev b2)
[Code]......
View 4 Replies
View Related
Jan 13, 2011
I have installed Fedora 14 on my new laptop Thinkpad T410 but the wireless card is not detected.
I tried to install the drivers but got error. How to install the driver.
[root@sheril sheril]# lspci
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) .....
View 1 Replies
View Related
May 7, 2010
I started on ubuntu 8.10 and my wireless card has always worked,Since i did a fresh install of ubuntu 10.04 it still seems to work to a point.I can see networks, click them and use a password to connect but it never seems to carry on, I typed the password correctly and after a minute it asks for it again.I have read a post about problems other people are having and that i need to install a different program.But i cant install another program if there is no wireless as apt-get doesn't work without internet connection.So... I need to download something that will fix it (possible update if one has been released) to xp (partition) then access xp partition from ubuntu and install it.
View 9 Replies
View Related
Oct 20, 2010
I have an issue with wireless connectivity on my laptop. Its a HP dm3 and the intel network adapter is supported as I can scan and detect wireless access points.However, when I attempt to connect to my home network, it fails and this is probably a result of two things: The BSSID is missing and/or the DHCP client ID is missing.I am running Kubuntu 10.10 32 bit
View 2 Replies
View Related
Jul 21, 2011
I'm running an ubuntu maverick server, and I'm having a slight problem with networking. I've only got one ethernet line running into my room, and I've got loads of computers. The server has 2 ethernet ports, one integrated into the motherboard, one on a PCI card that I took from my old server. The on board ethernet never worked on my old server- but I only tried it out post-install, it was hooked up to the card during install (For the record, networking on linux has *never* worked for me if I installed then plugged in the networking stuff after the fact). So I just used the card instead. Transferred the hard drive into a new machine, and lo and behold, it would only work after I transferred in the card from the old one. What I wanted to set up is a basic NAT system, where the network connection is routed through from my server to my main desktop- but when I run ifconfig, my card is not detected, just lo and eth0. How can I fix this?
View 3 Replies
View Related
Apr 7, 2011
I want to load Atheros wireless card to ubuntu linux OS having kernel 2.6.32.21. I have loaded the atheros driver and I observed the following log messages when card was inserted.
[ 55.732223] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[ 55.732294] pci 0000:04:00.0: reg 10 32bit mmio: [0x000000-0x00ffff]
[ 55.810152] ath5k: disagrees about version of symbol ieee80211_free_hw
[code]....
My suspect was the driver was 2.6.35.1 kernel based i may need to update my kernel, but i have other laptop having 2.6.32-21 kernel and this card works fine.
View 2 Replies
View Related
Jan 26, 2011
I am running the latest version of arch linux on a Dell Latitude D420. So far everything has worked perfectly except the wireless. It seems that Arch does not even detect the wireless because ifconfig -a only gives me the loopback and eth0. I installed ndiswrapper as well as the drivers. lsmod | grep ndiswrapper shows that ndiswrapper is being loaded on boot. I tried to install the iwp3945 drivers, but they have become obsolete so pacman was unable to find them. I also tried installing the iwl3945 drivers as explained here [URL] but still no luck.
View 14 Replies
View Related
Oct 27, 2010
1 ) make and model of wireless device Athreos 5k
2 ) driver version in use dont know
3 ) any error message. -
abhishek:/ # sudo /usr/sbin/iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a
Flags: bus master, fast devsel, latency 0, IRQ 23
Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
[code]....
View 9 Replies
View Related
May 14, 2010
I am using Ubuntu 10.04. The Tata Photon+ card Huwai EC1260 was working flawlessly. However, I recently did a firmware upgrade on the card that was provided by Tata Indicom for it to work on Windows 7.
After that, the card is no longer detected as a mobile modem in Ubuntu. If I try to add a new connection, all options are disabled (whereas earlier Tata Photon card would appear automatically).
The product ID has changed. What change can I make to Ubuntu to enable it to detect the card again.
View 6 Replies
View Related
Apr 21, 2011
Been using Ubuntu for 1 yr now on my Dell Dimension 8250 but a newbie with my Averatec AV3270-EH1 laptop circa 2005. Ubuntu 10.04 does not detect the Integrated WLAN card/adapter. I've looked at all the forums/posts but none had the issue I have. When I type lspci into the terminal i get this back:
00:00.0 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
00:00.1 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. K8M800 Host Bridge
[code]....
And when I type in iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
View 1 Replies
View Related
Feb 26, 2010
I have installed trixbox 2.8.0.3 in Intel MAC mini PC, installation completed successfully. After reboot network card was not detected.
My MAC mini PC comes with nVidia Corporation MCP79 Ethernet card. how to enable Ethernet card with out affecting the tribox. trixbox-2.8.0.3 version comes with Cent OS 5.4. [Moderator edit: s/deducted/detected/]
View 5 Replies
View Related
Jun 26, 2011
I am using a Compaq presario laptop. I installed Ubuntu 11.04 (32 bit) within windows 7.Initially my WiFi was running fine in Ubuntu without me doing anything. Now suddenly Ubuntu has stopped showing any of the WiFi networks. I have not done any changes in Ubuntu.When i booted to my Win 7, it was able to detect the network. I uninstalled and reinstalled Ubuntu, with no avail. But Ubuntu is able to detect the wired network when connected. I am at a loss.
View 9 Replies
View Related
May 15, 2010
I am using a Toshiba Satellite M200. Sometimes after a wakeup ubuntu does not detect any wireless networks. This does not happen all the time only some times but, when I restart my computer the wireless networks are detected.
View 2 Replies
View Related
