i am testing the opensuse 11 installation on the Eee pc (Eee Box B202). My installation source is in the network drive but i can't seem to point it to this destination because the network card is not detected. This Eee pc is using a jmicron network card and i can't seem to find any related drivers on the net.
View 1 RepliesI have Onboard Realtek ethernet card (eth0) it worked fine but suddenly it stopped working when i see in yast it shows hwinfo not found. when i use hwinfo --netcard it gives realtek card name thats all. I went to yast >lan> edit> hardware and tried to add r8169 module but it was not accepting. previously created ifcfg-eth0 file is available but its not getting up.when i say ifup eth0 it say interface not found. the same messg is also available in /var/log/boot.msg.
View 4 Replies View RelatedMy network cards were fine under Wubi Lynx. I decided to upgrade to Ubuntu Studio Lynx on its own partition, and the DVD install routine failed to detect the network card. Where do I go from here?***1 ) Machine Brand and Model (PC/Laptop):Acer 1410 (dual amd64 netbook, about a year old)***2) Network Interfaces
>lspci
01:00.0 Ethernet controller: Atheros Communications AR8131 Gigabit Ethernet (rev c0)
02:00.0 Network controller: Intel Corporation WiFi Link 1000 Series
[code]....
In new Acer Extensa 5635G i install 11.2 but lan card don`t work,wireles too!Hеrе info
Code:
/sbin/lspci
07:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
09:00.0 Ethernet controller: Attansic Technology Corp. Device 1063 (rev c0)
/usr/sbin/hwinfo
[Code]..
1 ) make and model of wireless device Athreos 5k
2 ) driver version in use dont know
3 ) any error message. -
abhishek:/ # sudo /usr/sbin/iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a
Flags: bus master, fast devsel, latency 0, IRQ 23
Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
[code]....
I recently installed Ubuntu 9.10 on an old family laptop. It is a Compaq Presario V2000. Everything works perfectly except no wireless networks are recognized, even though I know there are available networks. My network controller is detected but is not doing it's job, which is finding available wireless networks! Using "system testing" I found this out about my network controller:
"Detecting your network controller(s):
Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)"
url
I don't have any sound after installing Linuxant ALSA driver. I tried uninstalling it and the hsf driver, didn't help. Reinstalling ALSA didn't help either. Ubuntu doesn't detect my sound card, and aplay doesn't detect my sound card. lspci -v output for sound card:
Code:
00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1)
Subsystem: Acer Incorporated [ALI] Device 0126
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 10
[code]....
I have unfortunately found myself unable to properly boot up openSUSE because I decided to buy the Acer Aspire with the i5 Processor.
I have the Intel Graphics Media Accelerator HD (GMA HD) graphics card, and unfortunately from all my searching online and on openSUSE, I have been unable to find a driver for this that works for linux, and in addition I don't know how to install a driver outside of a GUI.
My openSUSE boots up to the boot choosing screen (regular openSUSE or failsafe), and then that nice list of functions being done is displayed, but as soon as the daemon has started, suddenly my screen goes blank and I am unable to do anything about it. Beyond this point, my OS loses all functionability, and while I can hear it computing, I am unable to actually tell WHAT it is computing. get a driver for this and to install this driver and get this GUI running, that would be great.
I added to my machine PC running debian and others, ubuntu, pc wireless card:,the same card I used it on other machine, it ran nice.On the other machine i have Ethernet Controller instead of Class ffff.I installed the divers firmware-ralink and other realtek and network-manager, but nothing.on other machine, that was enough to run it correctly.and ifconfig dosn't give wlan0,iwconfig did't give characteristic of wlan0.does this mean that the bios didn't recognize it as a network card
View 3 Replies View RelatedI just installed Linux Mint 9 as a dual boot install with Win XP. Trying to activate wireless network card driver and video driver. Pops up: "You are not authorized to perform this action".How do I get authorized?
Now every time I boot Win XP, the Internet Explorer menu bar is all blacked out and goofy. If I log out and back in it corrects itself. If I reboot it's blacked out again. Re-installed IE8. Still blacks out.Also Firefox in Win XP crashes expectantly. It has NEVER crashed on me previously.
I have bought a new laptop with W7 installed. And I installed dual boot with Ubuntu 9.10 on it.I tried to connect my laptop to Internet by Ethernet port. It works with W7, but Ubuntu doesn't detect my Network card .After some research on Internet, I suppose that it's a problem of drivers for this card.Here some parameters I could get :
>ifconfig :
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
[code]...
I'm in serious need of some help. The network adapter on the motherboard of my main machine apparently failed about noon today. This machine serves as the firewall and router for my home office LAN, and so it has two network adapters, the second being a PCI card installed in the only PCI slot of the mobo. The mobo's adapter served the WAN while the PCI card serves the LAN.Since the mobo has only one PCI slot, none of the other PCI cards I have on hand could be used. Instead, I pulled an unused PCI-e dialup modem card from the machine, and bought a PCI express gigabit card to put in its place.
The problem is that the machine (running Hardy 8.04.4 LTS) does not recognize the new card at all. Running lspci shows only the old PCI card that serves the LAN. Similarly, running "sudo lshw" shows only the old PCI card together with a virtual adapter that's part of my VirtualBox installation on that system.I then dual-booted into Vista Home and attempted to install the new card there, using the CD that came with it. Vista detected the card and asked for the disk, but then was unable to find any drivers on the disk!The box says the card is from Star Tech, and the instruction sheet says its model is ST1000SPEX.If anyone can point me to the correct module to add to the startup list and/or remove from the blacklist, that may get me going again.
I have an Acer Laptop and I am trying to use Linux Redhat 5 on it but for some reason the NIC is not detected by Linux. It is a bit surprising to me that the same problem was seen in my desktop computer but after changing the NIC to a different slot the Linux OS detected the NIC and it is working fine but my laptop still has the same problem.
From troubleshooting point of view:
1. Installed Linux multiple times but it didn't work.
2. Tried to add the hardware (NIC) but it didn't work.
Note: The NIC was working fine when I first installed Linux but after sometime it didn't. The laptop is dual boot (Windows & Linux) when I boot via windows the NIC works fine but not with Linux.
NIC Details:
Device Type: Network Adapter
Manufacturer: Broadcom
Location: PCI bus 2, device 0, function 0
I have tired everything I know how to do and I can not install the driver for the rtl8191se. I read the instructions that say to run:
sudo make
I have been through this before with Fedora. Ubuntu supported my wireless card but not my display so I am switching to this OS. Does anyone know how to install the driver on 11.4 suse?
joecamel@linux-1b2w:~/Downloads/rtl_92ce_92se_92de_linux_mac80211_0003.0620.2011> sudo makemake -C /lib/modules/2.6.37.1-1.2-desktop/build M=/home/joecamel/Downloads/rtl_92ce_92se_92de_linux_mac80211_0003.0620.2011 modules
make: *** /lib/modules/2.6.37.1-1.2-desktop/build: No such file or directory. Stop.
make: *** [all] Error 2
joecamel@linux-1b2w:~/Downloads/rtl_92ce_92se_92de_linux_mac80211_0003.0620.2011>
I recently installed SuSE 11.1 (64 bit) on my system
AMD Phenom II 940 3.0 Ghz;Biostar TA790GX 128M Motherboard with ATI Radeon HD 3300 Graphics card built in;
4 Gb (2*2 sticks) DDR2 800 MHz RAM
The installation went smoothly, But on first restart and login (and subsequent ones too!) I get a light purple screen with a skyblue box at top left corner, with xconsole written on it. when I Left click anywhere on the screen, I get a popdown with a number of options, of which only XTerm (bash shell) and exit (logout) options work. Now I know the HD 3300 graphics card drivers are not built into the SuSE 11.1 distribution, and I have already downloaded them (Linux ones)from ATI website. I login as Superuser, and type init 3 to go to a very basic screen,login as user, change to superuser again and then run the following file i downloaded from ATI:
sh ati-driver-installer-9-4-x86.x86_64.run
The result/output at the command prompt:
Created directory fglrx-install.ubanI5
Verifying archive Integrity... All good.
Uncompressing ATI proprietary linux driver-8.602...
.....(lot of dots)...
ati-driver-installer-9-4-x86.x86_64.run: line 295: ./ati-installer.sh: Permission denied Removing temporary directory: fglrx_install.ubanI5
Once again, i tried everything in superuser login.
Also I tried making changes via sax2 command, it doesnt seem to work. A window opens where I see that my graphics card has been detected but thats about it. nothing else in that option, everything is greyed out (nothing to be selected)
I have an HP Pavilion dv6-2120ca and I'd like to find out where to find the graphics driver. This is the card: TI Mobility Radeon HD 4200 Graphics I plugged in my MP3 player in and it worked with Opensuse.
View 2 Replies View RelatedI installed openSuse 11.2 64bit (DVD version). Later I installed the graphic card driver. Then I noticed that it's not working well due to an improper installation (didn't use the manual that you provided here). So I uninstalled the driver. Then, after reboot, instead of a regular desktop, I get a CLI and I'm requested to enter my login information. But in the boot menu, if I enter to the failsafe option, then everything works fine. How can I change the CLI to the regular desktop?
View 9 Replies View RelatedI'm very new to openSUSE, so I need easy, clear instructions on how to install the driver for RaLink RT2561T wi-fi card. I have the driver and everything, I just don't have a clue on how to install it!
View 5 Replies View RelatedI have a Realtek gigabit onboard ethernet (RTL-8110SC/8169SC)It was working in 9.10.After upgrading to 10.04, the connection dropped to 10MB. Now, lspci -v shows the card, but Ubuntu no longer recognizes eth0!I have no connection on the machine. I've been digging around the forums, but can't seem to find what I need.
View 2 Replies View RelatedI've been using Slackware distribution for few years now, Setup new system with Xen Server 5.5 and installed Slackware 13 on it, but network card is not detected and can't seem to make it work.
View 4 Replies View RelatedWireless card detected but cannot connect to a wireless network
I have install it suse 11, and everything went well until the wireless thing is not working, my card is Broadcom BCM4318, I see my card on the network settings but I cannot configure the card, and also I cannot connect to a wireless network, can someone tell me what to do here, I am loosing my patient....
I have downloaded and installed Fedora 10.Now I am setting up the network and in the 'network configuration' it finds the wireless device (ralink) in the 'hardware' section of the configuration - I set this to eth0 (it originally set itself to wan0 and I still had the same problems, now it doesn't give me the option to put it back to wan0).Now I goto the devices tab and try to set up the device with eth0 - which it seems to find.But when I goto activate the device it tells me that eth0 cannot be found
View 2 Replies View RelatedAm trying to install the correct driver for my RV710 Radeon HD4350 grahics card.which version out of these two I should install: * x11-video-fglrxG02 (for HD2000 series and later) * x11-video-fglrxG01 (for Radeon 9500 - X1900)
View 3 Replies View RelatedI have spent ages looking at similar problems but not not quite the same. I have installed 11.4/Gnome (x86) and wanted to use my GT430 card. I went here: 'http://en.opensuse.org/SDB:NVIDIA_drivers' and used the 'one click' install for current cards. All went ok until I rebooted and I got a 'gdm[1239]: WARNING: GdmDisplay: display lasted 0.846578 seconds' message. I got five of these in succession until the 'gdm[1239]: WARNING: GdmLocalDisplayFactory: maximum number of X display failures reached: check X server log for errors' appeared and it popped me down to an init 3 login.
So, I deleted the blacklisting conf file so that I could get back in to Gnome on Nouveau (which I did ok). I then noticed there was no /etc/X11 Xorg.conf file so I ran /usr/lib/nvidia-xconfig to generate one (which it did) - but it made no difference. I am at a loss know after spending 8 hours on this. Any pointers would be greatly appreciated. My machine is still at fresh install state so even if I have to reinstall 11.4 it does not matter.
[Code]...
I'm going to come right out and say I am a complete novice with Linux/SUSE. The equipment I'm having a problem with is a little web-server that was purchased by my employer that has, quite suddenly, stopped functioning. I was changing the IP address within YaST, at which point the device offered to update itself, which I saw no harm in. Post-update, however, I was unable to so much as ping the device.
I tried "ifconfig eth0": "Error fetching interface information: Device not found." I went into network settings via YaST and found that there are two cards now listed as: RTL8111/8168B PCI Express Gigabit Ethernet controller Both IP addresses are "Not configured". The information pane, for both cards, cites:
RTL8111/8168B PCI Express Gigabit Ethernet controllerBusID : 0000:02:00.0 Unable to configure the network card because the kernel device (eth0, wlan0) is not present. This is mostly caused by missing firmware (for wlan devices). See dmesg output for details. The only difference in either of the cards is the BusID (0000:02:00.0 and 0000:03.00.0)
I can neither edit nor delete either of these cards. As I mentioned, I am a total Linux novice, and am at a total loss for what to do next, or even how to find critical information about the system itself. I know enough to check dmesg, but not enough to have any clue what to look for in the output.
I am attempting a Network installation of openSuse 11.3 on an old desktop which has IBM Boot Manager so that I can boot to one of three OSs, openSuse being the third. Sadly the installation of openSuse fails before the CD initial boot has finished. Looking at the text log of the starting process the problem appears to be a driver and the last line of text where it stalls refers to eata driver.
There are 4 hard drives in the machine, configured as two RAID 1 arrays driven by a DPT 2144W hardware raid card. (Very old but very good). If I Google eata I get a good deal on SCSI raid and DPT cards but I am out of my depth when they say a kernel module is needed.
Another concern is that the RAID arrays are configured using a bootable DOS configuration disk and once this is done they are recognized by other OSs such as eCS and OS/2. The arrays are just treated as single drives so these OS installations do not interfere with the card configuration. I am concerned because I cannot afford to lose the data on the drives but it appears the linux driver might want to rebuild the arrays.
I installed 10.3 (after buying it a couple of years ago and letting sit on the shelf) and can't get it to configure my ethernet connection or my wireless card. Yast doesn't include a list of available cards, and the error I get in installation-network setup is that the kernel isn't present. The machine I'm installing this on is a Lenovo, in which there isn't a discrete ethernet card (it's in the motherboard), but my wireless card (a Cisco LINKSYS 802.11G) is a discrete card. Because I'm divorcing Microsoft for a number of valid reasons, I don't have Windows available on that box.
View 4 Replies View RelatedI use OpenSuse 11.1. My graphic card is an intel Q43/Q45 chip. I was instructed to update my xorg and mesa packages in order to make on application work (it was crashing my x server). After I did so, x wouldn't start:
intel(0): No kernel modesetting driver detected
Screen(s) found, but none having a usable configuration
Now I am stuck with vesa if I want to have x running at all. I tried reverting to the versions of mesa and xorg I had before, when everything worked, but to no avail.
What can I do? (I am by no means an expert and that I don't know linux very well, and even less openSuse... just has to use it at work....)
I have installed opensuse11.3 on my dell desktop. I get the gui with only 4 or 8 bit colors. I have resolution 0f 1024x768, which I have given at installation time. I cannot change it any more. I have followed your SDB:Configuring graphics cards - openSUSE guide. here is my lspci output
[code]....
I have tried to configure the xorg with command Xorg -configure. I surprised that it cause Segmentation fault. I have captured the Xorg -configure command in strace. I am pasting here certain last lines, I cannot paste the whole output because it is too large.
[code]...
i just installed debian after about 2 weeks of using ubuntu afterriend suggested switching, and it's not detecting my wireless card in the network settings. i'm new at linux so try to keep it simple if you can please,i read the sticky about this and here's the info it said i should provide
ispci -knn Code: 00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07)
Kernel driver in use: agpgart-intel
[code]...