I have a Realtek gigabit onboard ethernet (RTL-8110SC/8169SC)It was working in 9.10.After upgrading to 10.04, the connection dropped to 10MB. Now, lspci -v shows the card, but Ubuntu no longer recognizes eth0!I have no connection on the machine. I've been digging around the forums, but can't seem to find what I need.
View 2 RepliesI am using Ubuntu 10.04. The Tata Photon+ card Huwai EC1260 was working flawlessly. However, I recently did a firmware upgrade on the card that was provided by Tata Indicom for it to work on Windows 7.
After that, the card is no longer detected as a mobile modem in Ubuntu. If I try to add a new connection, all options are disabled (whereas earlier Tata Photon card would appear automatically).
The product ID has changed. What change can I make to Ubuntu to enable it to detect the card again.
I have bought a new laptop with W7 installed. And I installed dual boot with Ubuntu 9.10 on it.I tried to connect my laptop to Internet by Ethernet port. It works with W7, but Ubuntu doesn't detect my Network card .After some research on Internet, I suppose that it's a problem of drivers for this card.Here some parameters I could get :
>ifconfig :
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
[code]...
I'm in serious need of some help. The network adapter on the motherboard of my main machine apparently failed about noon today. This machine serves as the firewall and router for my home office LAN, and so it has two network adapters, the second being a PCI card installed in the only PCI slot of the mobo. The mobo's adapter served the WAN while the PCI card serves the LAN.Since the mobo has only one PCI slot, none of the other PCI cards I have on hand could be used. Instead, I pulled an unused PCI-e dialup modem card from the machine, and bought a PCI express gigabit card to put in its place.
The problem is that the machine (running Hardy 8.04.4 LTS) does not recognize the new card at all. Running lspci shows only the old PCI card that serves the LAN. Similarly, running "sudo lshw" shows only the old PCI card together with a virtual adapter that's part of my VirtualBox installation on that system.I then dual-booted into Vista Home and attempted to install the new card there, using the CD that came with it. Vista detected the card and asked for the disk, but then was unable to find any drivers on the disk!The box says the card is from Star Tech, and the instruction sheet says its model is ST1000SPEX.If anyone can point me to the correct module to add to the startup list and/or remove from the blacklist, that may get me going again.
I added to my machine PC running debian and others, ubuntu, pc wireless card:,the same card I used it on other machine, it ran nice.On the other machine i have Ethernet Controller instead of Class ffff.I installed the divers firmware-ralink and other realtek and network-manager, but nothing.on other machine, that was enough to run it correctly.and ifconfig dosn't give wlan0,iwconfig did't give characteristic of wlan0.does this mean that the bios didn't recognize it as a network card
View 3 Replies View Relatedfor some reason my graphics card is no longer detected by Ubuntu, just and hour ago everything was working perfectly (as Ubuntu usually does for me) and now it acts as if it's not there.
View 9 Replies View RelatedMy network cards were fine under Wubi Lynx. I decided to upgrade to Ubuntu Studio Lynx on its own partition, and the DVD install routine failed to detect the network card. Where do I go from here?***1 ) Machine Brand and Model (PC/Laptop):Acer 1410 (dual amd64 netbook, about a year old)***2) Network Interfaces
>lspci
01:00.0 Ethernet controller: Atheros Communications AR8131 Gigabit Ethernet (rev c0)
02:00.0 Network controller: Intel Corporation WiFi Link 1000 Series
[code]....
I have downloaded and installed Fedora 10.Now I am setting up the network and in the 'network configuration' it finds the wireless device (ralink) in the 'hardware' section of the configuration - I set this to eth0 (it originally set itself to wan0 and I still had the same problems, now it doesn't give me the option to put it back to wan0).Now I goto the devices tab and try to set up the device with eth0 - which it seems to find.But when I goto activate the device it tells me that eth0 cannot be found
View 2 Replies View Relatedfor some reason, ubuntu cant see it anymore. so how to fix? windows still prints to this printer on the network. I deleted the printer in ubuntu and tried to redetect and now it says no printer at that address.
before I deleted it, I recall it saying something about the backend had failed?
The problem with my wireless network. I have Dell DV6 Pavilion 2115 eg laptop and i installed Ubuntu 11.4 and internet and wireless worked, until i reboted my system it has disapear. I cant no longer to connect to a wireless network. It dont shows me any wireless network. My wireless card is Atheros AR 9285 802.11b/g/n Wifi Adapter
View 9 Replies View RelatedI have a msi netbook with ubuntu netbook remix installed and it was working great until yesterday when suddenly it stopped detecting my home network. There are no problems on my two other machines, so I'm sure the problem is the netbook. I have no idea how to go about troubleshooting this. I was hoping someone could help me by giving me a place to start.
View 2 Replies View RelatedI have an absolutely bizarre hardware issue (concerning the Atheros AR8132 PCI-E Fast Ethernet Controller) that has been giving me quite a bit of grief for a while, and having completely hit a wall on this one, I'm a reasonably-experienced Linux user of several years, and have been running Ubuntu 9.10 on an Acer AOD250 netbook for several months out. I know that this model has wireless issues out-of-the-box (easily fixed), but it did not have any noticeable ethernet issues. That is, until I attempted an installation of Arch Linux.
During the Arch Linux installation, the ethernet card was initially detected, but unable to be used (because of a bad module in the kernel released with the installer). As I didn't know the fix for this at the time, I decided to reinstall Ubuntu 9.10. This time, however, the system failed to recognize the wired ethernet whatsoever. Instead, the external activity lights for the port (green and orange) are ALWAYS on, yet the device doesn't function.
I have done a successful install of the latest drivers directly from Atheros for the device and have them automatically loading with the kernel during boot, but as the device isn't recognized, the drivers aren't doing any good. Relevant information:
Code:
root@niobium:~# lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
[Code]...
I have a ZTE HSUPA USB Modem Model:MF636 which used to work great and then is not longer detected.
I am using Fedora 12 and was having problems with the modem not been properly detected and filed a bug, which turned not to be a problem of NetworkManager, but an issue with udev.
https://bugzilla.gnome.org/show_bug.cgi?id=603433
I followed instructions to edit /lib/udev/rules.d/61-option-modem-modeswitch.rules and then it worked fine.
Now the modem is again not properly detected. Here is a copy of the results from dmesg code...
I have tried restoring the file that I edited. It was back to the stated previusly reported. I also have tried to run an older kernel. Then I updated to the latest kernel available for Fedora 12. Nothing seems to work.
I have an Acer Laptop and I am trying to use Linux Redhat 5 on it but for some reason the NIC is not detected by Linux. It is a bit surprising to me that the same problem was seen in my desktop computer but after changing the NIC to a different slot the Linux OS detected the NIC and it is working fine but my laptop still has the same problem.
From troubleshooting point of view:
1. Installed Linux multiple times but it didn't work.
2. Tried to add the hardware (NIC) but it didn't work.
Note: The NIC was working fine when I first installed Linux but after sometime it didn't. The laptop is dual boot (Windows & Linux) when I boot via windows the NIC works fine but not with Linux.
NIC Details:
Device Type: Network Adapter
Manufacturer: Broadcom
Location: PCI bus 2, device 0, function 0
I have Onboard Realtek ethernet card (eth0) it worked fine but suddenly it stopped working when i see in yast it shows hwinfo not found. when i use hwinfo --netcard it gives realtek card name thats all. I went to yast >lan> edit> hardware and tried to add r8169 module but it was not accepting. previously created ifcfg-eth0 file is available but its not getting up.when i say ifup eth0 it say interface not found. the same messg is also available in /var/log/boot.msg.
View 4 Replies View Relatedi am testing the opensuse 11 installation on the Eee pc (Eee Box B202). My installation source is in the network drive but i can't seem to point it to this destination because the network card is not detected. This Eee pc is using a jmicron network card and i can't seem to find any related drivers on the net.
View 1 Replies View RelatedI've been using Slackware distribution for few years now, Setup new system with Xen Server 5.5 and installed Slackware 13 on it, but network card is not detected and can't seem to make it work.
View 4 Replies View RelatedWireless card detected but cannot connect to a wireless network
I have install it suse 11, and everything went well until the wireless thing is not working, my card is Broadcom BCM4318, I see my card on the network settings but I cannot configure the card, and also I cannot connect to a wireless network, can someone tell me what to do here, I am loosing my patient....
I have a dual boot with W'XP and RHEL 5. M/B is MSI.
In XP the LAN is detected but not in LINUX.
I have just upgraded from 9.10 to 10.04 and now my wireless card isn't being detected as far as I know. It was working perfectly in the previous version. At the moment I've physically put an ethernet cable straight to the router.
[code]...
I have brought a new DELL INSPIRON 1410. I installed ubuntu 10.04 but my ethernet card is not getting detected where as in windows 7 is working..
View 2 Replies View RelatedI bought a new TOSHIBA C660 - i5010 today and installed.Lucid Lynx 10.04 on it, but it has not detected my wirelessg broadcom 80211 (STA) driver debp interface.
View 1 Replies View Relatedim having some trouble connecting the wireless card to my wifi network, theres is a hint using the terminal
remora@remora-laptop:~$ sudo lshw -C network
[sudo] password for remora:
*-network DISABLED
description: Wireless interface
[code]....
I started on ubuntu 8.10 and my wireless card has always worked,Since i did a fresh install of ubuntu 10.04 it still seems to work to a point.I can see networks, click them and use a password to connect but it never seems to carry on, I typed the password correctly and after a minute it asks for it again.I have read a post about problems other people are having and that i need to install a different program.But i cant install another program if there is no wireless as apt-get doesn't work without internet connection.So... I need to download something that will fix it (possible update if one has been released) to xp (partition) then access xp partition from ubuntu and install it.
View 9 Replies View RelatedI have an issue with wireless connectivity on my laptop. Its a HP dm3 and the intel network adapter is supported as I can scan and detect wireless access points.However, when I attempt to connect to my home network, it fails and this is probably a result of two things: The BSSID is missing and/or the DHCP client ID is missing.I am running Kubuntu 10.10 32 bit
View 2 Replies View RelatedI'm running an ubuntu maverick server, and I'm having a slight problem with networking. I've only got one ethernet line running into my room, and I've got loads of computers. The server has 2 ethernet ports, one integrated into the motherboard, one on a PCI card that I took from my old server. The on board ethernet never worked on my old server- but I only tried it out post-install, it was hooked up to the card during install (For the record, networking on linux has *never* worked for me if I installed then plugged in the networking stuff after the fact). So I just used the card instead. Transferred the hard drive into a new machine, and lo and behold, it would only work after I transferred in the card from the old one. What I wanted to set up is a basic NAT system, where the network connection is routed through from my server to my main desktop- but when I run ifconfig, my card is not detected, just lo and eth0. How can I fix this?
View 3 Replies View RelatedI want to load Atheros wireless card to ubuntu linux OS having kernel 2.6.32.21. I have loaded the atheros driver and I observed the following log messages when card was inserted.
[ 55.732223] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[ 55.732294] pci 0000:04:00.0: reg 10 32bit mmio: [0x000000-0x00ffff]
[ 55.810152] ath5k: disagrees about version of symbol ieee80211_free_hw
[code]....
My suspect was the driver was 2.6.35.1 kernel based i may need to update my kernel, but i have other laptop having 2.6.32-21 kernel and this card works fine.
recently installed 10.04 on his hp pavilion laptop and we got everything working fine, including the wireless internet. When he installed some recommended software updates his card is no longer being detected although wired networking is still fine.
ryan@ryan-laptop:~$ sudo lshw -c network
[sudo] password for ryan:
*-network:0 UNCLAIMED
[code]...
I have just installed Fedora 14 on my desktop machine and have just discovered that it can't detect my WiFi card. The card is an Edimax EW-7711In which the makers say will run with Linux. I know that the card works fine with Ubuntu because my brother uses the same card in his Ubuntu machine but he is away until after Christmas so I don't know what he did to make it work other than I know he used ndiswrapper and the Windows drivers that were supplied with the card. I have looked for ndiswrapper in the Fedora repositories but it doesn't appear to be there.
View 14 Replies View RelatedI have a problem with Netgear Wireless WG311v3 card and it is not listed in "ifconfig -a". Network Manager does not see the Netgear card either, just eth0 the onboard wired NIC. Here is the result of lspci.
Code:
[root@mylinux ~]# lspci -nn
02:00.0 Ethernet controller [0200]: Attansic Technology Corp. Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller [1969:1026] (rev b0)
03:00.0 IDE interface [0101]: Marvell Technology Group Ltd. 88SE6101 single-port PATA133 interface [11ab:6101] (rev b2)
[Code]......