Ubuntu Networking :: Network Card Not Detected During Install (Was Fine Under Wubi)?
May 20, 2010
My network cards were fine under Wubi Lynx. I decided to upgrade to Ubuntu Studio Lynx on its own partition, and the DVD install routine failed to detect the network card. Where do I go from here?***1 ) Machine Brand and Model (PC/Laptop):Acer 1410 (dual amd64 netbook, about a year old)***2) Network Interfaces
>lspci
01:00.0 Ethernet controller: Atheros Communications AR8131 Gigabit Ethernet (rev c0)
02:00.0 Network controller: Intel Corporation WiFi Link 1000 Series
[code]....
View 3 Replies
ADVERTISEMENT
Apr 4, 2010
I have bought a new laptop with W7 installed. And I installed dual boot with Ubuntu 9.10 on it.I tried to connect my laptop to Internet by Ethernet port. It works with W7, but Ubuntu doesn't detect my Network card .After some research on Internet, I suppose that it's a problem of drivers for this card.Here some parameters I could get :
>ifconfig :
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
[code]...
View 4 Replies
View Related
Jun 16, 2010
I'm in serious need of some help. The network adapter on the motherboard of my main machine apparently failed about noon today. This machine serves as the firewall and router for my home office LAN, and so it has two network adapters, the second being a PCI card installed in the only PCI slot of the mobo. The mobo's adapter served the WAN while the PCI card serves the LAN.Since the mobo has only one PCI slot, none of the other PCI cards I have on hand could be used. Instead, I pulled an unused PCI-e dialup modem card from the machine, and bought a PCI express gigabit card to put in its place.
The problem is that the machine (running Hardy 8.04.4 LTS) does not recognize the new card at all. Running lspci shows only the old PCI card that serves the LAN. Similarly, running "sudo lshw" shows only the old PCI card together with a virtual adapter that's part of my VirtualBox installation on that system.I then dual-booted into Vista Home and attempted to install the new card there, using the CD that came with it. Vista detected the card and asked for the disk, but then was unable to find any drivers on the disk!The box says the card is from Star Tech, and the instruction sheet says its model is ST1000SPEX.If anyone can point me to the correct module to add to the startup list and/or remove from the blacklist, that may get me going again.
View 3 Replies
View Related
Aug 27, 2010
I added to my machine PC running debian and others, ubuntu, pc wireless card:,the same card I used it on other machine, it ran nice.On the other machine i have Ethernet Controller instead of Class ffff.I installed the divers firmware-ralink and other realtek and network-manager, but nothing.on other machine, that was enough to run it correctly.and ifconfig dosn't give wlan0,iwconfig did't give characteristic of wlan0.does this mean that the bios didn't recognize it as a network card
View 3 Replies
View Related
Aug 27, 2010
I have a Realtek gigabit onboard ethernet (RTL-8110SC/8169SC)It was working in 9.10.After upgrading to 10.04, the connection dropped to 10MB. Now, lspci -v shows the card, but Ubuntu no longer recognizes eth0!I have no connection on the machine. I've been digging around the forums, but can't seem to find what I need.
View 2 Replies
View Related
Dec 9, 2009
i am testing the opensuse 11 installation on the Eee pc (Eee Box B202). My installation source is in the network drive but i can't seem to point it to this destination because the network card is not detected. This Eee pc is using a jmicron network card and i can't seem to find any related drivers on the net.
View 1 Replies
View Related
Mar 7, 2009
I have downloaded and installed Fedora 10.Now I am setting up the network and in the 'network configuration' it finds the wireless device (ralink) in the 'hardware' section of the configuration - I set this to eth0 (it originally set itself to wan0 and I still had the same problems, now it doesn't give me the option to put it back to wan0).Now I goto the devices tab and try to set up the device with eth0 - which it seems to find.But when I goto activate the device it tells me that eth0 cannot be found
View 2 Replies
View Related
Sep 7, 2010
I've recently salvaged a computer I found gathering dust in the basement and decided I'll have it running on Fedora (I have a summer studentship coming up that needs Linux use so I thought I'd best start learning!). Following a clean install, Fedora can see the wireless network just fine. I try to connect and nothing happens. Half of the time it will ask for the PSK (yes, I promise I'm entering it correctly) and the other half of the time it will just stop. When it does ask for the PSK I enter it (correctly) and it will ask me again... and again.
Quote:
uname -r
2.6.33.3-85.fc13.i686
Quote:
lspci
00:0b.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
[Code]....
View 11 Replies
View Related
Apr 22, 2011
just installed Ubuntu 10.10 (if I am not wrong) on my XP computer using Wubi. The problem now is that whenever I boot up, there is no sign of Ubuntu. The computer just goes straight into Windows XP. I checked the C: drive (main hard disk) and I see a folder called "ubuntu" and I am quite sure that Ubuntu is supposed to boot from there right? Could someone please help me out? How can I trouble shoot and get Ubuntu to boot up (using the Wubi install, that is
View 3 Replies
View Related
Nov 1, 2010
I have an Acer Laptop and I am trying to use Linux Redhat 5 on it but for some reason the NIC is not detected by Linux. It is a bit surprising to me that the same problem was seen in my desktop computer but after changing the NIC to a different slot the Linux OS detected the NIC and it is working fine but my laptop still has the same problem.
From troubleshooting point of view:
1. Installed Linux multiple times but it didn't work.
2. Tried to add the hardware (NIC) but it didn't work.
Note: The NIC was working fine when I first installed Linux but after sometime it didn't. The laptop is dual boot (Windows & Linux) when I boot via windows the NIC works fine but not with Linux.
NIC Details:
Device Type: Network Adapter
Manufacturer: Broadcom
Location: PCI bus 2, device 0, function 0
View 4 Replies
View Related
Mar 12, 2011
I have no Internet Access with Firefox
I first tried an upgrade from 11.3 to 11.4 and lost Internet Access, so i re-loaded 11.4 from scratch on clean partitions.
I am connected to my wireless WPA2/PSK connection, have an IP, am able to see the network.
I turned off and disabled the SUSE firewall.
I tried setting Firefox proxy settings to auto and to none, i dont use proxy.
I am currently posting this through an SSH connection to my 11.1 server from the new install of 11.4 on a Dell latitude D600 laptop (not using the on-board Broadcomm that is an issue for a later date).
I am running out of ideas anyone got a clue.
View 9 Replies
View Related
May 23, 2010
I have Onboard Realtek ethernet card (eth0) it worked fine but suddenly it stopped working when i see in yast it shows hwinfo not found. when i use hwinfo --netcard it gives realtek card name thats all. I went to yast >lan> edit> hardware and tried to add r8169 module but it was not accepting. previously created ifcfg-eth0 file is available but its not getting up.when i say ifup eth0 it say interface not found. the same messg is also available in /var/log/boot.msg.
View 4 Replies
View Related
Jan 6, 2010
I've been using Slackware distribution for few years now, Setup new system with Xen Server 5.5 and installed Slackware 13 on it, but network card is not detected and can't seem to make it work.
View 4 Replies
View Related
Oct 29, 2010
I just got Ubuntu and am new at this stuff. I have a dual boot windows 7 64 bit one and ubuntu 10.4. I booted ubuntu at startup and then tried to go online, but it says my wireless device is disabled. I tried pressing the keys on my keyboard to see if that may work, but it doesn't. I am lost and new at this.
View 1 Replies
View Related
Mar 14, 2009
Wireless card detected but cannot connect to a wireless network
I have install it suse 11, and everything went well until the wireless thing is not working, my card is Broadcom BCM4318, I see my card on the network settings but I cannot configure the card, and also I cannot connect to a wireless network, can someone tell me what to do here, I am loosing my patient....
View 4 Replies
View Related
Jul 4, 2010
I installed ubuntu netbook remix (the new version 10),and when I try to install drivers for my network card it says I need an internet connection,when I cant access the internet,I even tried using a wired connection (since I usually connect via wireless),but still its no use. My netbook is the following: [URL]...
View 1 Replies
View Related
Jun 27, 2010
I have a dual boot with W'XP and RHEL 5. M/B is MSI.
In XP the LAN is detected but not in LINUX.
View 2 Replies
View Related
Apr 30, 2010
I have just upgraded from 9.10 to 10.04 and now my wireless card isn't being detected as far as I know. It was working perfectly in the previous version. At the moment I've physically put an ethernet cable straight to the router.
[code]...
View 9 Replies
View Related
Dec 3, 2010
I have brought a new DELL INSPIRON 1410. I installed ubuntu 10.04 but my ethernet card is not getting detected where as in windows 7 is working..
View 2 Replies
View Related
Jun 18, 2011
I bought a new TOSHIBA C660 - i5010 today and installed.Lucid Lynx 10.04 on it, but it has not detected my wirelessg broadcom 80211 (STA) driver debp interface.
View 1 Replies
View Related
Mar 12, 2010
I have a problem where l am builing RHEL 5.x servers and during the install it asks which network card you want to boot from. My servers all have 4 NICs in, broadcom. I am booting from a PXE server which runs the anaconda installer l have tried editing the kickstart files and also the pxe cfg file with various options, but have had no luck so far.
View 3 Replies
View Related
Mar 1, 2010
im having some trouble connecting the wireless card to my wifi network, theres is a hint using the terminal
remora@remora-laptop:~$ sudo lshw -C network
[sudo] password for remora:
*-network DISABLED
description: Wireless interface
[code]....
View 6 Replies
View Related
Feb 13, 2010
I recently installed Ubuntu 9.10 on an old family laptop. It is a Compaq Presario V2000. Everything works perfectly except no wireless networks are recognized, even though I know there are available networks. My network controller is detected but is not doing it's job, which is finding available wireless networks! Using "system testing" I found this out about my network controller:
"Detecting your network controller(s):
Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)"
url
View 3 Replies
View Related
May 7, 2010
I started on ubuntu 8.10 and my wireless card has always worked,Since i did a fresh install of ubuntu 10.04 it still seems to work to a point.I can see networks, click them and use a password to connect but it never seems to carry on, I typed the password correctly and after a minute it asks for it again.I have read a post about problems other people are having and that i need to install a different program.But i cant install another program if there is no wireless as apt-get doesn't work without internet connection.So... I need to download something that will fix it (possible update if one has been released) to xp (partition) then access xp partition from ubuntu and install it.
View 9 Replies
View Related
Oct 20, 2010
I have an issue with wireless connectivity on my laptop. Its a HP dm3 and the intel network adapter is supported as I can scan and detect wireless access points.However, when I attempt to connect to my home network, it fails and this is probably a result of two things: The BSSID is missing and/or the DHCP client ID is missing.I am running Kubuntu 10.10 32 bit
View 2 Replies
View Related
Jul 21, 2011
I'm running an ubuntu maverick server, and I'm having a slight problem with networking. I've only got one ethernet line running into my room, and I've got loads of computers. The server has 2 ethernet ports, one integrated into the motherboard, one on a PCI card that I took from my old server. The on board ethernet never worked on my old server- but I only tried it out post-install, it was hooked up to the card during install (For the record, networking on linux has *never* worked for me if I installed then plugged in the networking stuff after the fact). So I just used the card instead. Transferred the hard drive into a new machine, and lo and behold, it would only work after I transferred in the card from the old one. What I wanted to set up is a basic NAT system, where the network connection is routed through from my server to my main desktop- but when I run ifconfig, my card is not detected, just lo and eth0. How can I fix this?
View 3 Replies
View Related
Apr 7, 2011
I want to load Atheros wireless card to ubuntu linux OS having kernel 2.6.32.21. I have loaded the atheros driver and I observed the following log messages when card was inserted.
[ 55.732223] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[ 55.732294] pci 0000:04:00.0: reg 10 32bit mmio: [0x000000-0x00ffff]
[ 55.810152] ath5k: disagrees about version of symbol ieee80211_free_hw
[code]....
My suspect was the driver was 2.6.35.1 kernel based i may need to update my kernel, but i have other laptop having 2.6.32-21 kernel and this card works fine.
View 2 Replies
View Related
Jan 27, 2010
I've been using slackware for many years. I think I started with Slack 8. I know how to configure the network, I've had this same POS Dell computer for a few years now but the other day I tried to go to a different distro (first mistake) everything worked fine but it was not for me. Once you go slack you never go back! Anyway I had slack on here prior to the change and it all worked fine. I'm running slack 13 and all of a sudden my network is slow as balls! I set it up as I always have so I did some research and tried a few things, nothing worked. So i enabled DHCP and its fine now.. I have a dell xps 420. onboard intel nic. worked fine when i first installed slack 13. Anyone have any clue what to do? I would like my static IP on this machine.
View 6 Replies
View Related
Apr 28, 2011
I have been an Ubuntu user for a year or so. My level is still ultra n00b but I am trying. Whenever I update Ubuntu there is always a WiFi problem, always. So now I am having problems getting wifi to work in 10.10. In Network Manager I can view wifi networks fine but I cannot connect. I tried with wicd also but I got as far as "getting ip" and then it would hang up.
lspci
Code:
Code:
Code:
I am not sure what driver I am using as I don't know how to exactly ID my driver. I know there is a way to ID the driver using airodump-ng but I have yet to find it.
I have a feeling this is a driver issue as one time I was able to establish a connection that then dropped a few minutes later. I have a feeling I should be disabling/removing the current driver and replacing it with ipw3945 or possibly a driver ndiswrapped? The problem is I cannot figure out how to remove the current driver.
I was going to switch back to 9.04 but I thought I would try to manually figure this one out instead of taking the easy way.
View 2 Replies
View Related
Jan 9, 2011
i just installed debian after about 2 weeks of using ubuntu afterriend suggested switching, and it's not detecting my wireless card in the network settings. i'm new at linux so try to keep it simple if you can please,i read the sticky about this and here's the info it said i should provide
ispci -knn Code: 00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07)
Kernel driver in use: agpgart-intel
[code]...
View 1 Replies
View Related
