I have been installing via wiki instructions and I am stuck installing a USB wireless. Where should I be going with this?
PHP Code:
debianportable:/home/dave# modprobe rt73usb
debianportable:/home/dave# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[Code]....
I am trying to get my usb wireless to work on Ubuntu 10.4 I found a how to and followed it but when I did a Make install this is what I got.
make -C /home/ronald/Downloads/DPO_RT3070_LinuxSTA_V2.3.0.4_20100604/os/linux -f Makefile.6 install
mkdir: cannot create directory `/etc/Wireless': File exists
make[1]: Entering directory `/home/ronald/Downloads
[Code].....
I have a Ralink rt2870 chip. Since it did not work with 11.2 out of the box (should it not be in the kernel?), I had to install this driver from the software search area on opensuse.org:
After installing it, it works, but only at reduced speed, (I think), because when keeping the mouse over the list item (of that connection) in Network Manager, a window pops up saying I only have 54Mbit/s.
It says:
Type: WiFI
Interface: ra
Hardware adress: 00:15: .....
Driver: usb
Status: connected
Bit rate: 54 Mbit/s
I have recently installed Fedora 10 onto my PC, dual booting with XP, and I am fairly new to linux. I have been trying to connect to my wireless network, but cannot even get Fedora to recognise my wireless adapter (Belkin N1 +MIMO). I have tried to follow a few tutorials that go through either the ndiswrapper method or by using native drivers. Because I don't have an internet connection on Fedora, I have to boot into XP to download the files for either ndiswrapper or the native drivers, rather than installing using the terminal.I downloaded the ndiswrapper RPM, and it failed because of an 'unexpected error', and when using the tarball, it could not find the makefile. The native drivers did not install because of unresolved dependencies.
View 11 Replies View RelatedAfter having my usb wifi adapters working fine for some time, they stopped working and I can not get network connectivity.
Some one else was using my box and they reported seeing a kernel panic and then rebooted the box. Now there is no connectivity through the wifi interfaces.
I have seen the kernel panics related to this driver before, but usually a reboot has no ill effect.
Code:
root@Algalon:~# iwconfig wlan0
wlan0 RTxx70 Wireless ESSID:"a800" Nickname:"RT3070STA"
Mode:Managed Frequency=2.412 GHz Access Point: 00:0B:86:9A:08:80
Bit Rate=54 Mb/s
[Code].....
Im a Linux newbie and am running OpenSuse 11.3 (Gnome, 2.6.34.7-0.5-desktop Kernel) and Ive an Asus N13 wifi dongle (linux compatible). I currently connect using my laptopÅ› internal wifi but I bought the dongle due to trouble with weak signal. It came with some sort of code that can be "compiled" but I havent got a clue how to do that (and I have been researching this matter for quite some time now). I then came across a post where someone with the same USB stick created and added only two small files to his filesystem and it worked...for him (maybe becasuse he was on a different Distro )
Ralink RT2870 USB Stick and created the two files mentioned in the post (network_drivers.rules and network_drivers.conf) and placed them in ETC... etc, etc! I rebooted the system but NetworkManager only lists it as "device not ready" ... So now back to square one.
[Code]...
I am very new to Linux and need to install a driver for my wireless card. I am trying to install the RT3070 v2.0.1.0 driver from Ralink. I am running Fedora 2.6.29.4-167.fc11.i686.PAE. I have read the thread in the Solutions section about this driver, but unfortunately this is somewhat above my levels of comprehension, and I don't really know where to start.
Here is the output.
[chips@fedora wireless_utility]$ tar xvf RT3070_Linux_STA_v2.0.1.0.tar.bz2
tar: Record size = 8 blocks
2008_1225_RT3070_Linux_STA_v2.0.1.0/common/
2008_1225_RT3070_Linux_STA_v2.0.1.0/common/2870_rtmp_init.c
2008_1225_RT3070_Linux_STA_v2.0.1.0/common/action.c
2008_1225_RT3070_Linux_STA_v2.0.1.0/common/ba_action.c
2008_1225_RT3070_Linux_STA_v2.0.1.0/common/cmm_data.c
2008_1225_RT3070_Linux_STA_v2.0.1.0/common/cmm_data_2870.c
2008_1225_RT3070_Linux_STA_v2.0.1.0/common/cmm_info.c .....
cp: cannot stat `/home/chips/wireless_utility/2008_1225_RT3070_Linux_STA_v2.0.1.0/RT3070STA.dat': No such file or directory
make[1]: *** [install] Error 1
make[1]: Leaving directory `/home/chips/wireless_utility/2008_1225_RT3070_Linux_STA_v2.0.1.0/os/linux'
make: *** [install] Error 2
[root@fedora 2008_1225_RT3070_Linux_STA_v2.0.1.0]#
After reading some download documentations, I'm still confused on how to install Ubuntu Linux onto a USB Flash Drive so that it is portable and not connected to a single computer.
View 3 Replies View Relatedi don't have connection in my compuer write now so i whant to install RT2870 driver but i don't know how i found this tutorials [URL] but i can't install may be i have error in choise package this is my kernel version Linux Ouz3r4 2.6.35.10-74.fc14.i686 #1 SMP Thu Dec 23 16:17:40 UTC 2010 i686 i686 i386 GNU/Linux i found this driver too [URL] but how to install
View 1 Replies View RelatedI've just tried to install PS CS5 portable in wine but I get a R6034 error. Does anyone know what I need to do?
View 1 Replies View RelatedI am trying to install a RaLink RT2570 USB Enhanced Driver for my Linksys WUSB54G that I found the driver here:I understand that I have to install full kernel source (I'm running CentOS 5.4 i386). I installed the source by the following commands that I found on the web:Install kernel headers: # yum install kernel-devel Kernel-headersInstall kernel source code:
# cd /tmp
# wget http://mirror.centos.org/centos/5/updates/SRPMS/kernel-2.6.18-164.10.1.el5.src.rpm
# rpm -ivh kernel-2.6.18-164.10.1.el5.src.rpm
[code]....
I have a Linksys wusb600n v.2/rt2870 that Ubuntu isn't dececting ndiswrapper is installed and appears to have taken well to the XP drivers but the card itself is still not being detected. I looked at the Linux drivers for it but i have no idea how to install the tar.tar.something file(i cant even find the ralink site anymore).to rest of the process. I even managed to make my way up to the library to get a couple of books but the latest one was written in 2006. I installed root and tryed a few commands but nothing made sence.
View 1 Replies View RelatedI work at a local computer shop as a computer technician and we get many computer in daily that require external virus scans (having to take out the hard drives, sticking it in another machine) just to scan (if we're lucky we can sometimes just do it in safe mode).Now what I want to know is...
1. Is it possible to install Ubuntu to an external HDD and use it virtually anywhere I plug it in? Will it pick up the network card, graphics card, etc so I can just plug and go? (Of course there are drivers for some computers).
2. Is it possible to run a Windows oriented virus scanner on Ubuntu? I know I can use WINE to run Windows applications, but will it prove to be compliant with virus scanners as well?
3. The main reason why I want it to be able to pick up on hardware and just work is because I plan on using it for schooling / travelling as well, have all my documents etc saved on it for easy access.
I've used Ubuntu in the past on an old laptop that didn't have much memory, small HDD, and a crap processor but that was 5-6 years ago (I still have the disk they sent me for free ).
I'm running ubuntu 9.10 and I'm trying to get my RNX-ESYN1 with rt3070 chipset to work. I've tried to download and install the newest drivers from ralink's page and when I type "lsusb" in a terminal I get this "Bus 001 Device 002: ID 148f:3070 Ralink Technology, Corp." so that means if it's plugged in and should work. In the network manager it shows only my PCI broadcom card, but not my USB stick. When I type in the "iwconfig" command I get the "ra0" but not in the network manager.
ra0 RT2870 Wireless ESSID:"" Nickname:""
Mode:Auto Frequency=2.412 GHz
Link Quality=10/100 Signal level:0 dBm Noise level:-143 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
[Code]...
and still nothing changed, I got it to work once, but I reinstalled my system and can't get it to work again. I don't know if I'm doing something wrong. Last time I did it, both of my wifi adapters were showing up in the network manager at once and were working great. I need my Ralink to use with the aircrack which doesn't work with my broadcom.
I am trying to install this driver in ubuntu 10.10 for a week. I am getting this error when I type {sudo make}
cimi@cimi-pc:/etc/2010_0831_RT3070_Linux_STA_v2.4.0.1_DPO$ sudo make
make -C tools
make[1]: Entering directory `/etc/2010_0831_RT3070_Linux_STA_v2.4.0.1_DPO/tools'
gcc -g bin2h.c -o bin2h
make[1]: Leaving directory `/etc/2010_0831_RT3070_Linux_STA_v2.4.0.1_DPO/tools'
/etc/2010_0831_RT3070_Linux_STA_v2.4.0.1_DPO/tools/bin2h
cp -f os/linux/Makefile.6 /etc/2010_0831_RT3070_Linux_STA_v2.4.0.1_DPO/os/linux/Makefile
make -C /lib/modules/2.6.35-23-generic-pae/build SUBDIRS=/etc/2010_0831_RT3070_Linux_STA_v2.4.0.1_DPO/os/linux modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.35-23-generic-pae'
make[2]: *** No rule to make target `/etc/2010_0831_RT3070_Linux_STA_v2.4.0.1_DPO/os/linux/.c', needed by `/etc/2010_0831_RT3070_Linux_STA_v2.4.0.1_DPO/os/linux/.o'. Stop.
make[1]: *** [_module_/etc/2010_0831_RT3070_Linux_STA_v2.4.0.1_DPO/os/linux] Error 2
make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-23-generic-pae'
make: *** [LINUX] Error 2
This is the last driver in ralink website. The built-in driver works but don't recognize my chipset and i wanna install this driver. My URL card is levelone wua-0603 usb [URL].
I got a CentOS 5.3 fileserver machine (no monitor/kb/mouse). I'd like to "pair" it with a specific USB drive, so that when this USB drive is connected and mounted it would start a backup - just a simple cp /source /target will do for now - it's the "autorun on mounted a specific USB drive" part I can't really solve. Is there an elegant way to do this some sort of autorun? My only really rough idea to do it is to check if the USB drive is available with a script run in crontab every minute :-
View 7 Replies View RelatedWell, I want to be able to run some Linux in a VM at my school (on WinXP systems), via a USB stick.Two problems:
- Computers are mediocre
- Will be on many of them
I tried portable virtualbox but it starts very slow and runs slow without the guest additions. It just doesn't work right.What I need is a quick, portable VM that starts up quick and runs decently; I'm not expecting all that much from a USB stick but at least smooth cursor movement.I would like one that allows me to save changes on the virtual HDD, as opposed to a LiveCD style VM.
Is there a non-root, portable distribution of MySQL for Linux? I need to do some testing on a server that I do not have root access to.
View 2 Replies View RelatedI think there is something wrong with my Wine setup, but I don't know how to fix it or even what it is. Others have gotten this program to work without problems in Wine. This is the console output that I get from Wine before it crashes. What could be the problem?
I tried removing wine wine directory so that it would auotomatically get recreated when trying to run firefox. Firefox still crashed, but new information was output:
I would like some feed back on how I can take a media player case I bought from net bios flash with tiny-core and set up to load xmbc from the hdd. Its a China made 2" case I'm putting a tb drive in I'm farely sure that it uses a pretty basic mtp sys on its on board memory its compat with many media types but I want to make more types accesable on it and I want the xmbc media browser on it it has ability to playback in hd with hdmi as well as composite/component and s-vid as well as vga using one output like an ipod just plug the cord you need in great for travel and automobile this is device specs [URL]
View 3 Replies View RelatedI've created a wonderful (until this issue) portable copy of Ubuntu linux that will boot on mostly anything by using a USB enclosure for my laptop's 80GB SATA drive. So far so good, it boots and runs on everything, and on non-nVidia card setups was even detecting the drivers, or letting me install the required drivers for hardware acceleration and compiz. Because you know, the wobble windows are the most awesome thing ever.
Anyway, my desktop machine had an nVidia card, so I'm thinking, sure, I'll just install the nVidia drivers like before and everything will work happily. Not so-- now the desktop and any other nVidia cards work great, but it seems to have completely disabled any other graphics cards. When the kernel module detects that an nVidia card isn't present, it shoots up this nasty little dialog box giving me the option to boot into "low graphics" mode, which doesn't even allow me to use the correct screen resolution, much less see the installed graphics card and try to configure a driver for it.
Is there any way to configure Ubuntu (with the dreaded nVidia kernel module) so that it can use nVidia's drivers when an nVidia card is present, and default to the normal (not low-graphics) setup in other cases, so that it has a fair chance of using what's actually present? I'm not afraid to much with config files, I just don't know the underlying system well enough to feel comfortable diving in without a push in the right direction.
My portable hard drive (WD My Passport), which used to work correctly now does not automount on my Ubuntu system. It does work on a Windows machine or even when plugged into WD HD TV, which is a Linux based device. There's one NTFS partition spanning the whole drive.When I plug the disk in, I see the following in dmesg:[269259.504631] usb 1-2.2: new high speed USB device using ehci_hcd and address 20[269259.604674] usb 1-2.2: configuration #1 chosen from 1 choiceHowever it does not mount in GNOME and I don't see it when I type:sudo fdisk -lAny suggestions why this might be? I repaired the partition using chkdsk on Windows, so the issue is probably not filesystem related.
View 4 Replies View RelatedI have been using ubuntu 8.10 for over a year and have recently upgraded my huawei modem ubuntu will not recognise my new modem which has wireless capability so I went and got this new usb wireless adapter to connect using the wireless, I have followed the trouble shooting and have the windows drivers installed all ok but it will not enable the device I am at a total loss how to make it do what I need, I will say I am very thick when it comes to using the code to do anything and yet I build pc's and repair them for a hobby O im 54 years of age.
View 8 Replies View RelatedI have a fit-PC server with Debian GNU/Linux (Lenny). I would like to use it as a wifi access point since my Linksys WRT54GS has become unstable.I have a USB Ralink wifi NIC. When I insert the card to USB I can see this with lsusb: Bus 001 Device 002: ID 148f:2573 Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter.I have tried following various HOWTOs on using wifi card as AP in Linux, however, it seems that the card cannot go into monitor mode. I believe this is because I must use a newer driver or upload non-free firmware or something like that.I have tried installed wicd, but it does not help.
I bought this wifi adapter because I was told that it is one of the most common used Linux supported wifi cards that can be used as access point and a lot of other stuff.How do I set up this USB wifi card as wireless access point in Debian Lenny?
I've got a sitecom usb wireless adapter that uses the RT2870 chipset.I have got the rt2870sta module and have a ra0 interfaceI can set up a connection in the network tool and it recognises the usb device fine.
[root@genie devices]# iwconfig
ra0 RT2870 Wireless ESSID:"******" Nickname:"RT2870STA"
Mode:Auto Frequency=2.462 GHz Access Point: Not-Associated
Link Quality=10/100 Signal level:0 dBm Noise level:-97 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
I have no control over it and the wireless bit in Network Manager is greyed out. I got the firmware from the Ralink site
/lib/firmware/rt2870.bin
I have set the country code in the .dat file to 1 for channels 1-13 and selected channel 11 My netgear wg-614 wireless light has no activity.
I have installed the Fedora 14, and a Dlink usb wireless adapter (DWA-125) with rt2870 chipset, but this one isn't working with my OS.
I typed the lsusb command
Code:
Bus 001 Device 006: ID 07d1:3c0d D-Link System DWA-125 Wireless N 150 Adapter(rev.A1) [Ralink RT2870]
I downloaded the drivers from YUM, the rt2870 and also kmod-rt2870. I thing that this step is ok.
I typed the dmesg | grep 2870 command
Code:
[21421.956342] usbcore: registered new interface driver rt2870
When I open the /proc/modules file, it shows the line bellow
rt2870sta 542230 0 - Live 0xffffffffa02fc000
[Code].....
I've compiled and installed my rt2870sta.ko and the firmware to the correct locations but my ubuntu 10.10 is loading the one under
/lib/modules/2.6.38-25-generic/kernel/drivers/staging/rt2870/rt2870sta.ko.
How do I get it to use the correct driver? I've attached a screenshot of the module info.
I have a Sparklan WUBR-502GN USB dongle with the RT2870 chip. It has worked, (with a little effort) of previous installs of 9.04, 9.10, 10.04 and 10.10. However it refuses to work in 11.04. I followed the same procedures, (blacklisting, confirming device ID, modifying config.mk and rt_linux.h, sudo make & make install and removing staging/rt2870), outlined in past forum articles and that worked in the previous RCs, but the connection to my home network will not complete. Has something changed in 11.04 that is substantially different from past releases?
P.S. the only thing I haven�t done, since 11.04 was only installed moments before, is do the build essential and headers.
Having read and attempted several theories on how to resolve this issue to no avail.
Code:
root@bt:~# lsusb
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[code]....
my wireless adapter(WUSB600N) doesn't run when I log in. The driver is loaded on start-up but the green light is not on the adapter. I have to physically disconnect the adapter and plug it back in to get it recognised and it works fine afterwards
View 2 Replies View Related