I have an issue with Hard Drives in GNU/Linux CentOS 5.3I installed linux 5.3 frash copy to new SATA MAXTOR 1000GB Hdd.And see the partitions is SATA MAXTOR 1000GB (NEW INSTALLATION CentOS 5.3)
/dev/sda1 Boot
/dev/sda3 /
(/dev/sda2 is the SWAP)
[code].....
I'm in rescue mode with Centos 5.2 disk trying to install/mount a new disk to extract data out from the failed server.
Plugged in a new SATA drive and syslog shows the drive being detected
SCSI device sdg: blah
sdg: Mode Sense: 00 3a 00 00
sdg: unknown partition table
sd 3:0:0:0: attached scsi disk sdg
However fdisk and mount does not find the drive. I tried echo "---" /sys/class/scsi_host/host3/scan based on one of the previous threads but get "write error: invalid argument".
how should I get the drive to be usable?
In our company, we have one server with kernel, 2.6.18. because of our neads, we had to buy new hard disk,that slax live cd detects that as "Ibex Peak 2 port SATA IDE Controlle".Apparently this kernel does not support this device.Unfortunately according to our policy(definitely some dependency on company's softwares installed on this kernel) we can not upgrade our kernel.
View 1 Replies View RelatedI'm trying to setup Linux on my friend's system but none of my Live CDs (gparted, kubuntu) will detect the SATA HDD or SATA optical drive. I keep getting the error message "unable to find a medium containing a live file system". I can boot into gparted from a USB flashdrive but it will not recognize the SATA HDD or any of the partitions on it.
System info:
XFX GeForce 8200 (XFX MI-A78S-8209) motherboard
nvidia nforce 8200 chipset
Liteon ATAPI iHAS220 SATA optical drive
I've been struggling a bit with install F11. F10 installs without issue. I have two internal SATA drives, a PATA DVD-ROM and a USB drive. The BIOS recognizes everything. However, when I got to the disk partition utility, Anaconda could never detect one of the SATA devices. I tried swapping cables, ports, etc. No luck. Today, I ran across this Bug thread: [URL] I checked the screens Ctrl-Alt-F1-6. Nothing obvious. But, for fun (from the bug thread) I went to the prompt on 2 and ran:
dmraid -r -E It found an "nvidia" RAID "thingy". Forgive my ignorance on what it really is called or what it does. Anyway, I answered yes to erase the "thingy" and voila. I was able to install F11. Not sure if I made a good title, but I've seen bits and pieces of people having similar problems with F11. And BTW, the drive that had "nvidia" on it was from a machine that was using nvidia hardware RAID 0 - but F10 had no problems with it.
I've never owned an external SATA device, so I'm curious whether these devices are hotpluggable in Fedora. Some computer cases and case inserts have an external SATA connector that plugs into the motherbords built-in SATA connectors and extends the connection so it reaches outside the case. But can you plug and unplug SATA devices just as you do USB devices?
View 8 Replies View RelatedMy IBM IntelliStation M Pro desktop tower has IDE hardware: CD burner and CD player. My computer (which is ~ 6 years old I think) has an unused SATA power plug end and an unused SATA data transfer port so I thought I'd buy a SATA DVD burner/CD burner combo to replace the PATA CD burner. But I read the following line at Wikipedia and wonder exactly what it means:
en.wikipedia.org/wiki/Serial_ATA "Backward and forward compatibility- SATA and PATA At the device level, SATA and PATA (Parallel AT Attachment) devices remain completely incompatible�they cannot be interconnected......" What does that 'interconnected' really mean? Can I have my 2 IDE hard drives and my IDE CD player play nicely with a SATA DVD burner/CD combo burner? [My OS is MEPIS 8.5]
I've bought a new e-sata external HDD. It work fine if it's connected throught USB. The problem goes when I connect it throught e-sata. The disk isn't detected (see the first screenshot).I must restart my computer to get the HDD detected (the HDD must be pluged in while booting, I think).Is it possible to repair that? I need the HDD to be detected immidiately when connected, like USB, without any restart.
View 1 Replies View RelatedI tried to install 11.04, but the partition tool shows no HDD. If I try to run Ubuntu from the CD, I can explore the HDD but the partition tool in the installation program won't find it. What can be wrong with my Promise SATA controller
View 8 Replies View RelatedI have a i3 processor and MSI p55-cd53 motherboard. My problem is fedora cannot detect the 2nd SATA, so that I can configure raid1.
View 1 Replies View RelatedopenSUSE 11.3, 2.6.34.7-0.7-desktop, KDE 4.4.x, 3.0-P4, 2.5g mem. I replaced PATA-OEM optical drive with SATA-OEM works fine with all apps outside of and except with this widget. No problems until the swap. I have performed some updates and I have not put the PATA drive back in to see if the behavior changed because it was failing. It could be an update but the optical drive swap is my first suspect. This now. If I hover cursor over notifier widget icon "last plugged in device" will pop up with accurate last device until a click on the widget icon and selection of action for the recently plugged in device. Selected actions work fine ... once.
Then it no longer updates the new or retains the previous DVD/CD (or any USB external drive when connected) entry. Closing after viewing but with out selecting an action results in an empty list also. The menu remains empty there after and only removal of the widget and reinstall makes the devices appear again ... once. Then the behavior repeats if the widget is removed and reinstalled. I was wondering if this is likely to be a udev/rules.d problem related to the swap of the optical drives? The 70-persistant-cd.rules file shows two cd's after the swap:
[Code]...
If I delete or rename the 70-persistant-cd.rules file in udev/rules.d will it truly be recreated at boot and might it this fix the issue? Should I look elsewhere first at some var logs for errors? Reinstall 11.3 and let auto detect and config sort it out is also and option but I'd rather not, heh.
I am trying to install Debian 5.0 "Lenny" on a PC with a very new hardware config (i3 processor, DDR3 RAM,LG SATA DVD drive, and Seagate SATA HDD). During the hardware detection phase of installation, I get a message saying the driver for my CD drive is not known, and asking me to select one manually. The options I get are only 'devcdrom', which does not work, and my installation cannot proceed.
I tried the following:
1. I read in a similar query that to use SATA DVD drives, I will have to set some boot options, so tried entering install libatapi_enabled=1 as an install option. This showed 'unknown parameter' error followed by same problem.
2. My Intel m/b BIOS has an option to set the DVD drive to "Native" or "Legacy", default is Native. I also tried changing this to "Legacy". Still same problem.
3. Read that I have to point to different drivers, but don't know how to do this during the installation.
I have a working F-10 box with an older motherboard (pre-sata). The p-ata ports are full (4 drives), so I'm trying to add a sata controller and another drive. The sata controller plugs into the pci bus, but is not detected by the bios (very old). After booting, the OS loads the driver module(s) and detects the new controller and drive. I was able to add the new sata drive into the LVM system using system-config-lvm. All was fine until I rebooted.
I get pages of lvm errors and booting fails. It looks like it's trying to mount the volumes before the sata controller is modprobed. Is there a way to get the os to modprobe for the new controller before trying to mount? The extra drive space is on a data partition, not the boot partition.
All of my computers are second-hand (except 1 laptop but it doesn't count) and I see in my Dell 4600 there are 2 SATA connectors on the motherboard. I picked up a 250 GB SATA hard disk and cables recently and tried plugging it in but the system doesn't see it. I even disconnected all other disks to make sure there wasn't a conflict (master/slave) issue going on but the system still does not see it.
The disk is vibrating so I assume it is getting juice and is spinning. Is there a setting or something I have to do to tell the system to access the SATA? Do I have to look at RAID settings if there is only 1 SATA disk? Can I not have a SATA disk and an ATA disk plugged in at the same time? I want to try and determine if the disk is bad, or is it PEBKAC!
I'm trying to install 10.04b2 x64 on my new rig and for some reason the live cd can't detect both of my 1TB Sata 3 drives. There is no Raid and the bios has them flagged as IDE. I have also tried adding pci=nomsi to the boot string to no avail.
View 8 Replies View Relatedused to run ARC linux and Windows 7 on my computer and i am now trying to install Ubuntu 10.10 X86_64When i used the live disc of Ubuntu 10.04 and load the installer it finds my four harddrive they way it should... sda,sdb,sdc,and sdd...When i however try the same with ubuntu 10.10 it displays my usb cardreaders drives first and then my hardrives as sde sdf sdg and sdh.I tried installing ubuntu with the reader unplugged and then reconnecting it after installation...But when i then boot with the reader attached it says it cannot mount drives sda,sdb,sdc and sdd becuase they are not ready.I think it is again detecting the usb cardreader before the sata controller ...Is there a way for me to alter the boot detection order so it will find my harddrives first and then the usb cardreaders ports ?
View 1 Replies View RelatedI am trying to install FC4 in my pc having WDC WD800JD SATA HDD. During the installation it shows that no HDD found. I have searched a lot but no driver are found for fedora core 4.
View 10 Replies View RelatedRecently I installed Fedora 12 without any hassles except that the USB devices are not getting detected. I checked with /proc/interrupts and the ehci_hcd module doesn't get any interrupts. Here is my dmesg (done to show only USB related messages) :
Code:
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
[code]....
I am just getting started with Ubuntu and love it so far. It has breathed new life into an old Compaq Presario V2000 and once I get up to speed on it I hope to start running it on all the rest of our machines.
The only major problem I am having is that none of the USB devices I have plugged in are being detected. From what I have seen online I should be getting a notification and should be able to view the devices at Places/Computer but so far, nothing. Googling this problem it appears that individual devices often don't work but I could not find anything on all USB devices not working.
Any ideas as to what I am doing wrong here?
Last week, I received a used, older (built ~ 2005 or so) IBM ThinkCentre desktop (machine 8143-2EU) having a Pentium 4 (64 bit), 3.0 GHz CPU. It came with WinXP- 64 bit as the sole OS. When I tested my USB devices with the WinXP OS, they were detected and read. I wiped the WinXP and installed MEPIS 11- 64 bit. [There's only a single Intel Pentium 4, 64 bit CPU known to work for MEPIS 11- 64 bit. It's the Pentium 4 Prescott with EM64T. I don't know if my P4 is that one.] Things seem OK with my MEPIS 11- 64 bit OS except for the times when I plug in USB devices--> they're not detected nor read. In a MEPIS forum, a guy told me to try, after first plugging in the USB devices, running lsusb in Konsole. I do that, the system wakes up, and the USB devices are detected and read. But why do I have to do this to get my system to detect and read the devices? I've made the MEPIS system setting so that all USB devices are automounted when plugged in. Doing that did not correct this problem. As root, in Konsole, I ran hwinfo and noticed that for the USB controllers, the driver - uhci_hcd - is not active. Here's the hwinfo output for one of the USB controllers:
18: PCI 1d.2: 0c03 USB Controller (UHCI)
[Created at pci.318]
UDI: /org/freedesktop/Hal/devices/pci_8086_265a
[code]...
[I suppose or guess that all MEPIS users who don't have this USB-device-detection-and-read problem have uhci_hcd.] To see what would happen as a test, I also used a MEPIS 11- 32 bit Live DVD in this computer having the MEPIS 11- 64 bit OS. When I use the Live DVD, I have the same USB detection-and-read problem! What does that mean? With some USB devices plugged in while I'm using the Live DVD, I'm forced again to run lsusb in Konsole. This wakes up the system so that it detects and reads plugged-in USP devices. Why? Any idea on how to fix this? Does this problem seem more a software one rather than a hardware one?
I want to install Ubuntu 10.10 via a DVD-ROM but I faild. I got the message "no common cd-rom drive was detected." I have tried to install ubuntu 11.4 and failed too.
Hardware Setting:
DVD-ROM was attached to SATA 3.0 port.
SATA controller was set to IDE mode.
PCH is CougarPoint.
I use the same hardware setting to install Red Hat 6.0 and it works fine. I tried following boot option but in vain: noapic, acpi=off, nodmraid, all_generic_ide. It is ok to boot via a live usb but ubuntu 10.10 still can't find DVD-ROM. I have to use the hardware setting I descripted to install Ubuntu 10.10.
dmesg:
Code:
[ 1.892198] ata1: SATA max UDMA/133 cmd 0x3098 ctl 0x30ac bmdma 0x3070 irq 19
[ 3.309652] ata1.01: failed to resume link (SControl 0)
[ 3.469636] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[code]...
i'm using athlon 64 bit , asus a8vmx mbd, 1gb ram
View 3 Replies View RelatedAfter I installed my ati grapics driver (the ati driver from the ati website) my ubuntu has this weird problem. When loading there is a line that cought my attention:
Running DKMS auto installation service for kernel 2.6.34: fglrx (8.543)...Failed
I think that has something todo with the other error I get which is:
Primary device is not PCI
(EE No devices detected)
Fatal server error
no screens found
giving up.
I have an ATI 5650 Radeon mobile grapics card By the way.
My USB devices are being detected when I run the 'lsusb' command.However there is no driver that is set to the device.Also the /dev/sdX device is created so there is a mount point
View 1 Replies View RelatedI recently had a hard drive on a computer (not to be obvious), and I fried the computer. You may ask "well why did you do that?" well, simply because I had accidentally bumped and switched to 220 volts, rather than keeping it at 115 like a sane individual. Anyway, I got a new computer, swapped the hard drive. When I go to boot into ubuntu though, it gives me the following error:
Code:
Ubuntu is running in low-graphics mode
The following error was encountered. You may need to update your configuration to solve this.
(EE) No devices detected.
I also have XP on this hard drive, and it works almost better than it did on my old one, surprisingly. all i have to do now for it to be labeled as efficient, is to get some RAM. But anyway, what can I do about the error message? I tried booting into recovery, running dpkg from the list of options, and it did a couple of things.
Whenever I plug in my usb flash drive or my memory card adapter they are not detected. If you can help me I will provide any kind of information needed to solve the problem, just tell me what command to run. Also my cd/dvd drive is still not being detected or is mislabeled on ubuntu 10.04 lucid lynx.
View 3 Replies View RelatedI am having problems understanding how sound capable devices are being used on my Ubuntu10.10 64 bit system. I have an ASUS A8V motherboard with on-board multimedia functions provided through the VIA V8237 chip. BIOS gives me the option to disable this functionality and I have set BIOS this way. I want to use an M-Audio 24/96 card for all sound processing.
However, in applications like Audacity the VIA chip functions are all available and can be set as recording and playback devices. The same is true in ALSA.
Why does 'linux' (I have no idea which part of the OS) ignore the BIOS settings?
Furthermore alsamixer always selects the 'default' devices. Where and how are these set?
<System><Preferences><Sound> hardware tab list 2 'Internal Audio' devices but no M-Audio device. What are these devices? Only 1 of them appears to create any output with the 'Test Speakers' tab. This confuses me completely because the speakers are connected only to the M-Audio card.
None of the profiles for 'Settings for the selected device' match the capabilities of the M-Audio card (1 set of stereo inputs and 1 set of stereo outputs). So where are these profiles coming from? Which do I select for the M-Audio card?
What do the Input and Output tabs in <System><Preferences><Sound> mean? Are these different to the hardware tab? The 'Output' tab lists2 devices for sound output: 'Internal Audio Analog Stereo, Stereo' twice. What devices are these ?
I have installed Imgburn and it wont detect my cd drive, I configured wine and everything and no matter what I can't get it to recognize my driver, what am I to do?
View 9 Replies View RelatedI'm having issues getting the nvidia-current drivers working with a GeForce 8400 graphics card on Ubuntu 10.10 (x64). After running nvidia-xconfig and restarting, X fails to start with an error: No devices detected.
Here is my xorg.conf:
Code:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 260.19.06 (buildmeister@builder101) Mon Sep 13 04:59:45 PDT 2010
Section "ServerLayout"
[code]....
The hard disk is seen in the BIOS.
The partitions on it are accessible via the Places Menu on the Lucid Live CD.
It's just when I try to install, nothing is detected in Step 4 of 8, "Prepare Partitions".
An old 80GB IDE disk, on the other hand is seen by the partitioner.
I am not using RAID and it is not enabled in the BIOS.