I plan on installing a belkin wifi router. Is there any software to configure it ? also i need to increase the security as max as possible will my wifi be secure? only certain number of devices to access it also any software to display the number of devices accessing it like a radar? i am very fed up of all the command-line thinggy
View 1 RepliesBecause of the configuration of my house, I need two routers.I have a DLink ADSL router as my main router and the Belkin N1 as my repeater.I have set up the IP address in the Belkin to be 10.1.1.10 - my DLink is 10.1.1.1. I have disable the dhcp in the Belkin and set the DNS as ISP provided. [URL]..I have set the channel to 11 and in the Ubuntu Network Manger I have set the IPV4 to Link Local Only. I can see the Belkin and connect with my PC.but it will not take me through to the internet.
View 9 Replies View RelatedI cant seam to find out how to get my card to work i cant find out how to install the driver or finding the wifi card on the system.
View 9 Replies View RelatedI have a new belkin N1 router which I tested in somebody else's flat. It worked fine. When I got home I reset it by pushing a paperclip in the hole for 10+ seconds to erase this flat's internet connection settings (username and password and stuff). After this I plugged it the computer and tried to connect to it (wired connection) using 192.168.2.1 (this is correct for that router, it is not 192.168.0.1). But the browser says it is offline and cannot connect. The lights of the router cycle, the "modem router" light blinks continuously and the others briefly come on and go off again, every few seconds. I tried resetting it again, several times, leaving it off for a few hours, leaving it on for a few hours, etc.
View 2 Replies View RelatedI have just installed 11.04 alongside windows vista. I have been trying to connect my router but it keeps saying disconnected from network. I have ran all of the troubleshooting tips in ubuntu its self and everthing seems in order. is there any settings i need to change on my router or in ubuntu's edit connections programe? I managed to connect to the router once to upgrade from 10.10 to the 11.04 but even before upgrading to 11.04 i had problems connecting to the router.
View 6 Replies View RelatedI joined this forum so I can say my experience with the crappy belkin N150 router. It appears you need to run the setup cd under windows to make the router 'see' the modem. Under linux as someone pointed out you can easily enter the router setup from a browser ( enter 192.168.2.1 ) and connect to the router only (wired or wireless connection) but not the internet. Does anyone have any idea what the windows setup is doing to connect the router to the modem and how to do it under linux in the browser?
View 9 Replies View RelatedHow do I get my ubuntu 9.04 computer to recognise the USB wireless stick and then connect to my wireless d_link router?
View 1 Replies View RelatedUbuntu 9.04.
Belkin Wireless G router.
Has been working fine. Today it is not. I have done nothing to it. It just keeps saying "Looking up *********" and "Cannot connect to server".
I hard wired the pc to the modem and it works fine. Hard wired the pc to the router it works fine. Running wireless, both of my computers are not connecting.
If I remember, one of the lights on the router should be lit solid, just as it is on the modem. However, all lights are blinking. The only solid light is "power".
Last night I jumped into the linux world and finally installed Ubuntu in a dual boot system with XP on board as well (eventually I want to get rid of this). How can I get my wireless Belkin F5D8233-4 router working. I put the install disk in and it shows on the desktop but unable to execute - keep getting an error message. Getting frustrated...
View 6 Replies View RelatedI have a old laptop Dell C600 PIII 800mhz 256mb RAM 20Gb HDD and a floppy drive. It has 1 USB port and no wifi card.
I bought the Belkin F6D4050 v1 usb wireless adapter so that I could use it on the above laptop and connect to my wireless network at home. The Belkin USB wireless adapter has a Ralink xchipset
There was no specific Linux driver available but a workaround for an old driver worked. Some changes to the code and compiling gets the wireless adapter to work.
I have installed Arch on the laptop. I compiled it and its working fine
Questions 1.Arch linux releases new image only once or twice a year I have downloaded the latest available arch image and built froms scratch. When I update Arch (as it is a rolling release) the kernel also gets updated and the compiled driver fails to work. I have to recompile again for the new kernel. Is there a way I can compile this driver in the existing Arch or any other distro kernel and use as long as I can without updating so I do not have to recompile again
I have a Belkin wireless router model F5D7234-4 version 5. I switched to DHCP long enough to access the router via Firefox browser and look at all the settings. I turned off all encryption and other security related functions in order to just get it going. The IP of the router is 192.168.2.1 which is the default for this router. It is set to channel 6. I can not ping the router from either of two machines using regular ethernet or wireless. I have very limited experience with routers and am in need of help so I can use this for wireless connection to my living room box to my laptop in the bedroom about 50 feet away.
I tried changing the gateway from the living room box IP number to the router IP number with no success. I don't have anything connected to the internet port on the router. The living room box and the laptop are connected to the ethernet ports on the router. Ethernet works fine. Wireless does not. I compiled and installed the drivers for my wireless card on the laptop, a Realtek 8176 which uses the kernel modules rtl8192ce, rtlwifi and mac80211. ifup wlan0 brings up the wlan interface with these modules loaded. Right now I just want to be able to ping the router using regular ethernet. That would tickle me pink at this point. I downloaded the manual but I just can't seem to make headway.
I have a newer Belkin N+ router that has a USB port for accessing an external hard drive.I can access the HD with no problem in Windows.I am new to Linux/Ubuntu and cant seem to connect to the HD. In "Network" I have a folder "Windows Share" and within that folder is where I see the HD "CBHD" (name of my drive). I cant click it because when I do, i get an error message along the lines of (cant remember exactly right now) "Failed to mound"I typically access the drive in Windows via : \192.168.2.1
View 1 Replies View RelatedYou'll need to reply like I'm an absolute idiot. I cannot get the stupid thing to work. WINE won't install, and I'm really confused on how to make it work. If anyone could please give me a step-by-step, that would be great.
View 1 Replies View RelatedDoes anyone have an opinion on the BELKIN F5Z0142uk Enhanced Wireless ADSL Router Network Kit, I want to setup a small home LAN and this kit caught my eye, it includes a usb Wi-Fi dongle for connectivity to a desktop computer, one of my pc's doesnt have a network card so this sounds like a good idea. Whats the build quality like and is it reliable. The link: [URL]
View 2 Replies View RelatedI have an external hard drive connected to my router. From Windows I can access it, but from Ubuntu I can see the hard drive, but when I try to access, I'm asked for a password. However my network does not have a password neither the hard drive.
What must I do?
I recently purchased a TPlink 5 port switch, which for some reason didnt work with windows, only my ubuntu computer, I found a cheap wireless belkin router which also has 4 wired ports. It now works well except that it is slow searching for new servers eg, going to facebook creates a long wait and can even time out but once on the website everything works fast, The connection is 2.89 Mbps which is good for this area and ping is 45ms. What could I do to fix this problem. This affect my ubuntu computer and the windows xp pc as well
View 2 Replies View RelatedFor two days I've tried to get my new Belkin 7050 wifi stick up and running. No matter what I did nothing changed, at all. After close to 8hrs of straight trouble shooting I have made zero progress. Zero.
If you have a bunch of free time and want a project then feel free to play with this device. However if you're short on time or have work to get done just take it back to the store and get a different device.
Here's the over view of my situation :
- Ubuntu 8.04 : Device is detected. DHCP = Doesn't connect to router / get IP. Router can see device. Router has no security / password enabled.After several hours of trouble shooting Ubuntu I booted into win2k (supported by device)
- Win2k : Device is detected, official software installed. DHCP = Doesn't connect to router / get IP.
It does the exact same thing in Win2k as it does in Ubuntu. - Ubuntu 9.10 : Did a fresh install if 9.10 just to trouble shoot this problem. Symptoms are exactly the same. DHCP doesn't get an ip. There are no errors in /var/log/messages
- Ubuntu 9.10 : Blacklisted the regular drivers and did the ndiswrapper method, smooth sailing. After all is said and done it does the exact same thing. DHCP doesn't get an ip.
In all the trouble shooting I did (iwconfig, ifconfig, etc) I never received any error messages telling me that something had went wrong (besides the part where dhcp didnt get an ip).
[Code]...
I have a pc which has 2 network cards, 1 wifi and 1 ethernet card.
I'm using wifi card to connect to wifi network (internet) and i'm planing to share this wifi/internet connection via ethernet to wireless router (siemens sx763) so i can have internet on my other devices, e.g. mobile phone, laptop.
the only error message I can find comes from "dmesg|tail"all it shows is
"no IPv6 router"any body know what is going on here or where where to look for more clues the next time I get around public wifi Oh the windoze washers and apple polishers don't seem to have any problems at all
EDIT 6 Dec: More detailed log from wpa_supplicant I'm using Ubuntu Studio 10.10 x64. I want to get wireless networking going manually. My wireless networking works successfully in Windows 7 x64. I can get it working successfully without encryption but when I try and use WPA-PSK, wpa_supplicant gets stuck in a loop between GROUP_HANDSHAKE and COMPLETED, as shown in the log below.
I've been working mostly off the instructions in this post: [URL]... My laptop is a Dell Studio 1537. It has an Intel Wifi 5100. I'm connecting to a F5D7633-4 router running F5D7633-4Av1_UK_1.00.010 firmware, which is the latest version of the firmware I can find. When I set up WPA, it uses encryption technique TPIK. The other generic information is
Code:
$ iwconfig wlan0 up
04:00.0 Network controller: Intel Corporation WiFi Link 5100
$ lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 045e:074f Microsoft Corp.
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[Code]...
configure my Belkin Wireless USB adapter(F7D2101)? I attached the adapter and rebooted the system. I used the hardware info and it is listed but no drivers.
View 1 Replies View RelatedTrying to install a USB Belkin 150 to my Unbuntu box. The computer simply does not recognise the USB stick. Beleive I need a driver to install.
View 10 Replies View Relatedam running Ubuntu 10.04 ... only because for some reason that is the only version that will load onto my IBM pentium 4 desktop! I installed ndisgtk, ndiswrapper-common and ndiswrapper-utils-1.9 by using the Synaptic Package Manager GUI. Using Windows Wireless Drivers GUI, I installed the driver rt 2870 off the Belkin CD that came with the product. Status is "Hardware present: Yes"
here is the status of my lsusb and iwconfig:
finn@finn-desktop:~$ lsusb
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 045e:008c Microsoft Corp. Wireless Intellimouse Explorer 2.0
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 006: ID 050d:935a Belkin Components
It seems I have ndiswrapper working (I think!) ... but i still can't connect my wireless.
I'm looking at buying one of the above cards, and was wondering if anyone knew if they worked in master mode (e.g. as an access point). According to the Aircrack-ng site, they support packet injection and monitor mode. Is master mode support solely up to the driver used with the card, or does the card have to physically support it?
View 2 Replies View RelatedI am new to ubuntu, but recently learning a lot I from the past 2 days have been struggling to get my Wi-fi up and running, but there seems to be no success. I can't get the browser to open the ""Belkin Router"" Configuration page. I tried even reading the mannual but dosen't seem to work. I use a ""Belkin Basic N150"" router It is certainly not desinged for Ubuntu
View 2 Replies View RelatedI want to configure linux CentOS 5 as a router using iptable, .Im new in linux so I need the steps to do that
View 5 Replies View RelatedI have been experiencing slight problems while attempting to connect to the internet via a wireless router. I can connect to my router perfectly fine on Vista and I could connect to my friends router while I was in Ubuntu, but I can't connect to my router while on Ubuntu. I've been entering the same code that will work when I'm in Vista, but it wont work while in Ubuntu.
View 7 Replies View RelatedMy isp gave me a router which has wifi.
I added an ubuntu box acting as a router, so the layout is this:
Now, the lan has 192.168.2.0 subnet, and the external interface of the router is in the 192.168.1.0 subnet
So the problem is that the wifi assigns 192.168.1.0 ip's which doesnt belong or get filtered through my router/firewall...
I think I have unique problem. I have a d-link DWL G510 rev c.(Austrailian) WiFi card in my pc which is detected as
Quote:
Network controller [0280]: RaLink RT2561/RT61 rev B 802.11g [1814:0302] in lspci -nn.
iwconfig shows:
Quote:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=6 dBm
Retry long limit:7 RTS thrff Fragment thrff
Power Managementff
ppp0 no wireless extensions.
Now sometimes it detects my wifi router and shows its ssid in nm-applet. but when I try to connect, it tries for 3 or 4 minutes and then fails. for most of time it even does not finds my router.
I have a Dell Studio XPS15 laptop running 11.04 which works flawlessly with my router (it's a broadcom card btw). Now I'm setting up a new laptop for my Father-in-law which is a Dell Inspiron 15 which has intel Centrino 1000 wireless. I've installed and setup 11.04 on it. Everything runs great except..
Now it can see all the access points around so I assume the wireless card is properly detected and working. But when I try to log into my router and give it my password, it just keeps trying to connect and can't. I've double checked the settings with my own laptop and everything seems the same. why it won't log in? I'm leaving it as a dual boot with Win7 and I know that Win7 will log into the same router with the same password.