Ubuntu Networking :: Cant Access ExtHD Via Belkin Router With USB Port?
Jul 8, 2010
I have a newer Belkin N+ router that has a USB port for accessing an external hard drive.I can access the HD with no problem in Windows.I am new to Linux/Ubuntu and cant seem to connect to the HD. In "Network" I have a folder "Windows Share" and within that folder is where I see the HD "CBHD" (name of my drive). I cant click it because when I do, i get an error message along the lines of (cant remember exactly right now) "Failed to mound"I typically access the drive in Windows via : \192.168.2.1
View 1 Replies
ADVERTISEMENT
Jun 21, 2010
I have an external hard drive connected to my router. From Windows I can access it, but from Ubuntu I can see the hard drive, but when I try to access, I'm asked for a password. However my network does not have a password neither the hard drive.
What must I do?
View 9 Replies
View Related
Apr 13, 2010
Because of the configuration of my house, I need two routers.I have a DLink ADSL router as my main router and the Belkin N1 as my repeater.I have set up the IP address in the Belkin to be 10.1.1.10 - my DLink is 10.1.1.1. I have disable the dhcp in the Belkin and set the DNS as ISP provided. [URL]..I have set the channel to 11 and in the Ubuntu Network Manger I have set the IPV4 to Link Local Only. I can see the Belkin and connect with my PC.but it will not take me through to the internet.
View 9 Replies
View Related
Mar 1, 2010
I changed to a 4 port ethernet router (D-Link DSL-2542B Adsl2+)with intention to share Internet access with my brother (he's on Vista).Initially it all went well,but 3 days ago there were connection problems occured on the part of the ISP. Without realized the problem,I had reset the router.This morning I've been informed by the ISP that the connection has been re-established.So,I accessed the Internet via the 4 port router but failed to do so (server not found).Suspecting that the problem was from the 4 port router,I reverted to my old Adsl router (DSL-520B single port) and without any problem I managed to access the Internet back.I really need help to configure back the 4 port ethernet router to its initial state.
View 9 Replies
View Related
Jun 23, 2010
I have a new belkin N1 router which I tested in somebody else's flat. It worked fine. When I got home I reset it by pushing a paperclip in the hole for 10+ seconds to erase this flat's internet connection settings (username and password and stuff). After this I plugged it the computer and tried to connect to it (wired connection) using 192.168.2.1 (this is correct for that router, it is not 192.168.0.1). But the browser says it is offline and cannot connect. The lights of the router cycle, the "modem router" light blinks continuously and the others briefly come on and go off again, every few seconds. I tried resetting it again, several times, leaving it off for a few hours, leaving it on for a few hours, etc.
View 2 Replies
View Related
Jun 20, 2011
I have just installed 11.04 alongside windows vista. I have been trying to connect my router but it keeps saying disconnected from network. I have ran all of the troubleshooting tips in ubuntu its self and everthing seems in order. is there any settings i need to change on my router or in ubuntu's edit connections programe? I managed to connect to the router once to upgrade from 10.10 to the 11.04 but even before upgrading to 11.04 i had problems connecting to the router.
View 6 Replies
View Related
Jun 30, 2011
I have a Belkin wireless router model F5D7234-4 version 5. I switched to DHCP long enough to access the router via Firefox browser and look at all the settings. I turned off all encryption and other security related functions in order to just get it going. The IP of the router is 192.168.2.1 which is the default for this router. It is set to channel 6. I can not ping the router from either of two machines using regular ethernet or wireless. I have very limited experience with routers and am in need of help so I can use this for wireless connection to my living room box to my laptop in the bedroom about 50 feet away.
I tried changing the gateway from the living room box IP number to the router IP number with no success. I don't have anything connected to the internet port on the router. The living room box and the laptop are connected to the ethernet ports on the router. Ethernet works fine. Wireless does not. I compiled and installed the drivers for my wireless card on the laptop, a Realtek 8176 which uses the kernel modules rtl8192ce, rtlwifi and mac80211. ifup wlan0 brings up the wlan interface with these modules loaded. Right now I just want to be able to ping the router using regular ethernet. That would tickle me pink at this point. I downloaded the manual but I just can't seem to make headway.
View 2 Replies
View Related
May 10, 2011
You'll need to reply like I'm an absolute idiot. I cannot get the stupid thing to work. WINE won't install, and I'm really confused on how to make it work. If anyone could please give me a step-by-step, that would be great.
View 1 Replies
View Related
May 13, 2010
Does anyone have an opinion on the BELKIN F5Z0142uk Enhanced Wireless ADSL Router Network Kit, I want to setup a small home LAN and this kit caught my eye, it includes a usb Wi-Fi dongle for connectivity to a desktop computer, one of my pc's doesnt have a network card so this sounds like a good idea. Whats the build quality like and is it reliable. The link: [URL]
View 2 Replies
View Related
Dec 28, 2010
I recently purchased a TPlink 5 port switch, which for some reason didnt work with windows, only my ubuntu computer, I found a cheap wireless belkin router which also has 4 wired ports. It now works well except that it is slow searching for new servers eg, going to facebook creates a long wait and can even time out but once on the website everything works fast, The connection is 2.89 Mbps which is good for this area and ping is 45ms. What could I do to fix this problem. This affect my ubuntu computer and the windows xp pc as well
View 2 Replies
View Related
Jul 30, 2011
I'm curious is it possible to access your router settings. I'm trying to open up a port. I have done this in my firewall now I need to open up my port through my router. I'm using fedora 15.
View 5 Replies
View Related
Jul 2, 2011
I have a Centos 5.6 Linux Server configured as Router with NAT for my LAN. There are currently 2 NIC's on my server. One is connected to WAN , a PPOE connection (eth0) and eth1 is connected to a switch which supports my LAN. I have enabled NAT and configured iptables on my server and I am able to access internet from LAN and everything is working fine.I have a Belkin F5D8233-4v3 Wireless router and I need to configure wireless on my network so that I can access internet from my Laptop. The issue is that I have only 2 NIC's on my server, one Gigabit NIC integrated with my motherboard and another NIC which I am currently using for WAN access and LAN. I need to setup the Belkin as an wireless Access Point.
Can I connect my Belkin to my switch and set it up as a Wireless Access Point?? I have read about setup using 3 Nic's.Any ideas on how to configure my Belkin as Wireless Access Point with my existing setup? Is Belkin F5D8233-4v3 supported on Linux.
View 1 Replies
View Related
Aug 22, 2010
I have logged into my router and set up port-forwarding on port 22. I can log into the machine fine from a machine on the local network using the machines internal IP but when I try to log on from a remote machine using my router's external IP or my DyDNS host-name I get a message saying "connection refused" or "connection timed out." I have configured port-forwarding on the router and the firewall rules says that port 22 is open but when I nmap my routers external ip it says that only port 23 and 80 are open. I am very new to linux and networking.
View 8 Replies
View Related
Dec 16, 2010
I have an n900 phone and I'm trying to ssh to my desktop but I'm getting an error:
ssh: connect to host 58.xx.xx.xx port 22: Connection refused
I recently started using a router for I wanted to connect to net even with n900. I've tried to open the port from the setup page of the router however it doesn't seem to work. (find below the screenshot of setup page).
I've tried to ssh through slackware I've got as a virtual machine and I have the same problem although I was able to ssh through slackware before I started using the router.
View 1 Replies
View Related
Jun 18, 2011
I joined this forum so I can say my experience with the crappy belkin N150 router. It appears you need to run the setup cd under windows to make the router 'see' the modem. Under linux as someone pointed out you can easily enter the router setup from a browser ( enter 192.168.2.1 ) and connect to the router only (wired or wireless connection) but not the internet. Does anyone have any idea what the windows setup is doing to connect the router to the modem and how to do it under linux in the browser?
View 9 Replies
View Related
Mar 4, 2009
I have the wake on lan option enabled on my debian computer. If i wake it by sending:
-mac adres
-internal ip in my home network
-subnetmask
-port 7
It all works fine, but when i try to do it from outside my network and change the ip address to the router adress it wont go on. I have also opened the port 7 in my router.
View 6 Replies
View Related
Aug 29, 2010
I'm trying to get my SSH server I set up on my home box working from behind a router. A 2wire 2700HG-B gateway, in fact. Now, I know my server is working fine, because I can get into it via loopback, anywhere inside the LAN from another machine, OR if I go into the router's config and enable DMZ for the machine. However, I don't like having DMZ on all the time because of the kludge-ness of it, and the security issue of the complete absence of a hardware firewall.If I try to port forward and access it from outside the LAN using the external IP (or my DynDNS, because it's dynamic), it just times out. I have a nonstandard port (45) for the listen port of the server, to keep away hack attempts if I were using the standard 22. I used this to see if the port was open, and it said it was. But, I tried the trick of telnetting the IP with that port, and it also timed out, instead of printing stuff about OpenSSH.
Attached is a screenie of my router's firewall page, so you all can look at it and see if I'm an idiot and doing it wrong. You might notice uTorrent there, it's because this machine is a dual-boot with 7, and the router doesn't differentiate the OS's. Also the SSH @ 46 port is for the Windows side, with freeSSHd. I changed the port on that one so the client I have can distinguish them, so it can run a reachability test.
View 9 Replies
View Related
Feb 13, 2010
How do I get my ubuntu 9.04 computer to recognise the USB wireless stick and then connect to my wireless d_link router?
View 1 Replies
View Related
Oct 5, 2010
Ubuntu 9.04.
Belkin Wireless G router.
Has been working fine. Today it is not. I have done nothing to it. It just keeps saying "Looking up *********" and "Cannot connect to server".
I hard wired the pc to the modem and it works fine. Hard wired the pc to the router it works fine. Running wireless, both of my computers are not connecting.
If I remember, one of the lights on the router should be lit solid, just as it is on the modem. However, all lights are blinking. The only solid light is "power".
View 2 Replies
View Related
Sep 27, 2010
Last night I jumped into the linux world and finally installed Ubuntu in a dual boot system with XP on board as well (eventually I want to get rid of this). How can I get my wireless Belkin F5D8233-4 router working. I put the install disk in and it shows on the desktop but unable to execute - keep getting an error message. Getting frustrated...
View 6 Replies
View Related
Aug 23, 2010
how to access networking port and run scripts on that port so as to gain access of remote machine.is that possible through command prompt or through software.
i kno ip address of my frnd who is chattin with me .okay.i want to run an application on his computer .i came to kno tht we can run script o through port
View 2 Replies
View Related
Oct 2, 2010
I have a old laptop Dell C600 PIII 800mhz 256mb RAM 20Gb HDD and a floppy drive. It has 1 USB port and no wifi card.
I bought the Belkin F6D4050 v1 usb wireless adapter so that I could use it on the above laptop and connect to my wireless network at home. The Belkin USB wireless adapter has a Ralink xchipset
There was no specific Linux driver available but a workaround for an old driver worked. Some changes to the code and compiling gets the wireless adapter to work.
I have installed Arch on the laptop. I compiled it and its working fine
Questions 1.Arch linux releases new image only once or twice a year I have downloaded the latest available arch image and built froms scratch. When I update Arch (as it is a rolling release) the kernel also gets updated and the compiled driver fails to work. I have to recompile again for the new kernel. Is there a way I can compile this driver in the existing Arch or any other distro kernel and use as long as I can without updating so I do not have to recompile again
View 1 Replies
View Related
Mar 12, 2010
how i can open port 4444 in my system and in the router of my ISP cuase i used it to download and i dont to be blocked from ISP
View 2 Replies
View Related
Apr 29, 2011
I plan on installing a belkin wifi router. Is there any software to configure it ? also i need to increase the security as max as possible will my wifi be secure? only certain number of devices to access it also any software to display the number of devices accessing it like a radar? i am very fed up of all the command-line thinggy
View 1 Replies
View Related
Aug 1, 2010
I enabled D-Link (DSL-502T) router web management (I am aware of security implication). I was able remotely to login to the router (by typing http://23.45.xx.6y) before changing the default number 80. Then I changed the port number from the default value 80 to 21908 (https option is not available) for better security, and when I tried to login to the router by typing this :
http://23.45.xx.6y:21908
Yes I am aware that if I am physically near to the router then I can check that , but this is not the case with me. How can I make sure that I had changed port number form 80 to 21908? Does NMAP do a trick to reveal which port is used for web management ? or are there other better options?
View 4 Replies
View Related
Jan 26, 2010
I am trying to make a vnc connection from pc #2 to pc #1. Pc #1 is a debian pc behind a zyxel router (P-2602HW-D1A). Pc #2 is a windows xp pc another place at the internet.I have configured the zyxel router to forward incomming trafic on port 5902 to the local ip-adress of the debian box. The debian box is running a vnc server, listening on port 5902.But i dosn?t work.I have tryed to scan the zyxel routers ipadress on port 5902 from the internet, but the scanner says that the port is closed.The vnc server on pc #1 is working fine on the local network. I can connect to the server from a pc on the same side of the zyxel router.Is it deffenitly a router problem, or could it have something to do with debians own firewall?
View 2 Replies
View Related
Sep 2, 2010
what I have: Belkin G Wireless Router Model F5D7234-4. To attempt to get Subsonic working, I changed the port forwarding settings (Belkin calls it Virtual Servers) to forward port 4040 to my desktop computer. I then saved changes, and my wireless disconnected. I waited about 3 minutes, and nothing was happening, so I restarted my router. This left me in the position that I am in now. Even when the router and modem are fully booted, the router does not broadcast my SSID. In addition, a wired connection will not connect to the network through the router. This leaves me completely unable to use wireless, and unable to change any settings in the router.
View 3 Replies
View Related
Jun 9, 2010
I moved my server and network equipment, and now the wireless works but I cannot get my server online. I host a website, so this is kind of urgent.
I have a wireless router and can access the internet fine on my laptop. My server is wired & connected to the router. It sets up the networking properly.. ifconfig has an ip address, the default gateway is present. But I cannot ping google, or even the router. It says destination host unreachable.
So I go back to the laptop to check the router settings.. sometimes it likes to assign the server the wrong internal ip. But, I can't access the router settings either! The page (192.168.1.1) times out. Same with trying to ping the router. How can the laptop be online if it can't reach the router?
Oddly, ifconfig on my laptop reports an ip address starting with 99.233. It's always given me an internal address starting with 192.168. What's going on here? Is the router not allocating an internal ip? I use wicd to connect, if it's relevant.
We have a windows laptop that can only get a "local connection". Now it does sound like the router is forwarding directly to my laptop, instead of allocating internal ips.
View 1 Replies
View Related
May 18, 2010
I've managed to confirm that I can reach my home network via ssh from a remote location through my SMC Barricade when it is directly connected to the desktop machine but when the second router is put back into the chain ssh requests time out. The second router is a Linksys WRT 54GL running the Tomato firmware. The chain looks like this: ISP's router (bridged) --> Barricade -->WRT54GL-->desktop
The Barricade has port 22 forwarded to the Linksys' WAN address and it in turn forwards to the desktop address. It appears that it is a setting on the Linksys firmware that is preventing the remote connection. I've looked through the various settings many times but cannot see anything that would cause the problem.
View 4 Replies
View Related
Feb 17, 2011
i use slackware 13.1 i have apache, mysq, php - working i have a router netgear WPN824v2 - latest firmware port forwarding to my comp 192.168.1.105 port 22 i can access my ssh from my internel lan, but i cannot access it from the outside... i used [URL] to test the port and it says that is closed. i used PFportCheck Program on my other windows computer and it says that "port 22 is opened on another device!" - which is good because it's opened on this computer. also tried to changed the port on sshd_config to 6655 and 22 but it's still cannot connect...
View 1 Replies
View Related
