Last night I jumped into the linux world and finally installed Ubuntu in a dual boot system with XP on board as well (eventually I want to get rid of this). How can I get my wireless Belkin F5D8233-4 router working. I put the install disk in and it shows on the desktop but unable to execute - keep getting an error message. Getting frustrated...
View 6 Replies
Because of the configuration of my house, I need two routers.I have a DLink ADSL router as my main router and the Belkin N1 as my repeater.I have set up the IP address in the Belkin to be 10.1.1.10 - my DLink is 10.1.1.1. I have disable the dhcp in the Belkin and set the DNS as ISP provided. [URL]..I have set the channel to 11 and in the Ubuntu Network Manger I have set the IPV4 to Link Local Only. I can see the Belkin and connect with my PC.but it will not take me through to the internet.
View 9 Replies View Relatedvery new to using fedora and trying to install my belkin wireless adaptor is not working at all. It reads the disk but says there is an error.it still works fine on windows so i'm not sure how to fix this.
View 1 Replies View RelatedI have a new belkin N1 router which I tested in somebody else's flat. It worked fine. When I got home I reset it by pushing a paperclip in the hole for 10+ seconds to erase this flat's internet connection settings (username and password and stuff). After this I plugged it the computer and tried to connect to it (wired connection) using 192.168.2.1 (this is correct for that router, it is not 192.168.0.1). But the browser says it is offline and cannot connect. The lights of the router cycle, the "modem router" light blinks continuously and the others briefly come on and go off again, every few seconds. I tried resetting it again, several times, leaving it off for a few hours, leaving it on for a few hours, etc.
View 2 Replies View RelatedI have just installed 11.04 alongside windows vista. I have been trying to connect my router but it keeps saying disconnected from network. I have ran all of the troubleshooting tips in ubuntu its self and everthing seems in order. is there any settings i need to change on my router or in ubuntu's edit connections programe? I managed to connect to the router once to upgrade from 10.10 to the 11.04 but even before upgrading to 11.04 i had problems connecting to the router.
View 6 Replies View RelatedI joined this forum so I can say my experience with the crappy belkin N150 router. It appears you need to run the setup cd under windows to make the router 'see' the modem. Under linux as someone pointed out you can easily enter the router setup from a browser ( enter 192.168.2.1 ) and connect to the router only (wired or wireless connection) but not the internet. Does anyone have any idea what the windows setup is doing to connect the router to the modem and how to do it under linux in the browser?
View 9 Replies View RelatedHow do I get my ubuntu 9.04 computer to recognise the USB wireless stick and then connect to my wireless d_link router?
View 1 Replies View RelatedUbuntu 9.04.
Belkin Wireless G router.
Has been working fine. Today it is not. I have done nothing to it. It just keeps saying "Looking up *********" and "Cannot connect to server".
I hard wired the pc to the modem and it works fine. Hard wired the pc to the router it works fine. Running wireless, both of my computers are not connecting.
If I remember, one of the lights on the router should be lit solid, just as it is on the modem. However, all lights are blinking. The only solid light is "power".
I have a old laptop Dell C600 PIII 800mhz 256mb RAM 20Gb HDD and a floppy drive. It has 1 USB port and no wifi card.
I bought the Belkin F6D4050 v1 usb wireless adapter so that I could use it on the above laptop and connect to my wireless network at home. The Belkin USB wireless adapter has a Ralink xchipset
There was no specific Linux driver available but a workaround for an old driver worked. Some changes to the code and compiling gets the wireless adapter to work.
I have installed Arch on the laptop. I compiled it and its working fine
Questions 1.Arch linux releases new image only once or twice a year I have downloaded the latest available arch image and built froms scratch. When I update Arch (as it is a rolling release) the kernel also gets updated and the compiled driver fails to work. I have to recompile again for the new kernel. Is there a way I can compile this driver in the existing Arch or any other distro kernel and use as long as I can without updating so I do not have to recompile again
I have a Belkin wireless router model F5D7234-4 version 5. I switched to DHCP long enough to access the router via Firefox browser and look at all the settings. I turned off all encryption and other security related functions in order to just get it going. The IP of the router is 192.168.2.1 which is the default for this router. It is set to channel 6. I can not ping the router from either of two machines using regular ethernet or wireless. I have very limited experience with routers and am in need of help so I can use this for wireless connection to my living room box to my laptop in the bedroom about 50 feet away.
I tried changing the gateway from the living room box IP number to the router IP number with no success. I don't have anything connected to the internet port on the router. The living room box and the laptop are connected to the ethernet ports on the router. Ethernet works fine. Wireless does not. I compiled and installed the drivers for my wireless card on the laptop, a Realtek 8176 which uses the kernel modules rtl8192ce, rtlwifi and mac80211. ifup wlan0 brings up the wlan interface with these modules loaded. Right now I just want to be able to ping the router using regular ethernet. That would tickle me pink at this point. I downloaded the manual but I just can't seem to make headway.
I have a newer Belkin N+ router that has a USB port for accessing an external hard drive.I can access the HD with no problem in Windows.I am new to Linux/Ubuntu and cant seem to connect to the HD. In "Network" I have a folder "Windows Share" and within that folder is where I see the HD "CBHD" (name of my drive). I cant click it because when I do, i get an error message along the lines of (cant remember exactly right now) "Failed to mound"I typically access the drive in Windows via : \192.168.2.1
View 1 Replies View RelatedI plan on installing a belkin wifi router. Is there any software to configure it ? also i need to increase the security as max as possible will my wifi be secure? only certain number of devices to access it also any software to display the number of devices accessing it like a radar? i am very fed up of all the command-line thinggy
View 1 Replies View RelatedYou'll need to reply like I'm an absolute idiot. I cannot get the stupid thing to work. WINE won't install, and I'm really confused on how to make it work. If anyone could please give me a step-by-step, that would be great.
View 1 Replies View RelatedDoes anyone have an opinion on the BELKIN F5Z0142uk Enhanced Wireless ADSL Router Network Kit, I want to setup a small home LAN and this kit caught my eye, it includes a usb Wi-Fi dongle for connectivity to a desktop computer, one of my pc's doesnt have a network card so this sounds like a good idea. Whats the build quality like and is it reliable. The link: [URL]
View 2 Replies View RelatedI have an external hard drive connected to my router. From Windows I can access it, but from Ubuntu I can see the hard drive, but when I try to access, I'm asked for a password. However my network does not have a password neither the hard drive.
What must I do?
I recently purchased a TPlink 5 port switch, which for some reason didnt work with windows, only my ubuntu computer, I found a cheap wireless belkin router which also has 4 wired ports. It now works well except that it is slow searching for new servers eg, going to facebook creates a long wait and can even time out but once on the website everything works fast, The connection is 2.89 Mbps which is good for this area and ping is 45ms. What could I do to fix this problem. This affect my ubuntu computer and the windows xp pc as well
View 2 Replies View RelatedI have a dell desktop using 9.04 version before when belkin 4 port usb hub was working with keyboard, mouse, printer, webcam connected on it. I upgraded system to 11.04 when again USB hub was working. Recently certain upgrades happened on my system and USB hub stopped working. If I connect mouse, keyboard directly to usb port they are working but not when connected with usb hub. Present kernel version is 2.6.38.10. Since USB ports are limited so i have to use mouse, keyboard, printer, webcam through usb hub.
View 1 Replies View RelatedI'm looking at buying one of the above cards, and was wondering if anyone knew if they worked in master mode (e.g. as an access point). According to the Aircrack-ng site, they support packet injection and monitor mode. Is master mode support solely up to the driver used with the card, or does the card have to physically support it?
View 2 Replies View RelatedI have a belkin n wireless net card its model # f5d8053 v3 tring to get this card to work. have done some looking around and some of the places where i have looked they said DID work but are no longer working...the os on the computer i am trying to install this on is a 64 bit ubuntu
View 2 Replies View RelatedI am new to ubuntu, but recently learning a lot I from the past 2 days have been struggling to get my Wi-fi up and running, but there seems to be no success. I can't get the browser to open the ""Belkin Router"" Configuration page. I tried even reading the mannual but dosen't seem to work. I use a ""Belkin Basic N150"" router It is certainly not desinged for Ubuntu
View 2 Replies View RelatedI've got an old IBM Thinkpad T41 that I just play around with Ubuntu on. The internal Wireless card is broken, so I bought a Belkin F5D8013 PCMCIA Wireless N card a while ago. It worked fine with Ubuntu 8.04-9.10, but it will not work with 10.04. It sees the networks just fine and will let me type in the network password, but it will not connect. Everything else in my house connects without a hitch, so I know it is Ubuntu causing the problem.
View 1 Replies View RelatedI have a Compaq AMD64 that has ubuntu 9.04 on one HD that works great. I've installed 10.04 on a separate HD and had problems installing it. I have 10.04 running now but I can't get my wireless card to work. During installation I skipped setting up the wireless network. Now when I boot into the 10.04 partition I cannot get the nm-applet to work. I can't get it onto the task bar and I don't see it anywhere else.
I checked to see what drivers are installed, and since I have no connection with that OS I can't update or DL drivers for it. I'm pretty sure that it is because I skipped setting it up during installation. What do I need to do to get the wireless working now? I checked other threads and none seem to pertain to my situation. Since I have to log into the 9.04 partition, I can't copy/paste outputs very easily.
i am complitly new in Ubuntu and the world of Linux in general, so i said to my self its better late then never, i installed the last one 10.10. but i am having trouble with my wifi usb adapter (BelkinF5D7050 v 1000), the same adapter works perfect under XP in the same PC. when i go to NM i dont see it in the list of network cards "i see just my two other normal network cards + loopback" and i have permanent small "x" on the icon of NM up in the task bar, even if check or uncheck "Enable Networking", it alwayes show a info bubble "you are now offline", here is the result of all the command line that can help getting better view on my problem
[Code]....
I have just installed Ubuntu 9.10 alongside Windows 7 and it is not picking up my Belkin N wireless adapter?? So I went to go and download the Windows Wireless Drivers (ndiswrapper) software so I can install my adapter and the download center just says "Not available in the current data" and wont let me download it? Also I tried to download my nVidia drivers from software center and it said the same thing?
Never before have I had a problem with Ubuntu until now So can anyone point me in any directions as to how to get these installed???
I'm trying to get internet set up on my grandad's laptop (sony pcg-f590), which has a fairly old pcmcia belkin 54g wireless card. I've installed the relevant bcmwl5a.inf driver through ndiswrapper, and for a time wireless worked so I installed updates through update manager. however after restarting the network manager menu comes up with "wireless networks disconnected" and no list of networks (I know there are because my laptop works and his is sitting next to the router!). The light is on on the network card so I know the laptop is talking to it. Unplugging and replugging the card does nothing, and neither does restarting again.
View 1 Replies View RelatedInstalled F14 on my daughters HP Pavilion a131On. I rebooted multiple times. Do I need to activate something? I'm new to all of this but read through many threads to do as much as I could myself. I used the GUI to load the rt3070 drivers rather than rpm. The GUI is easier I think and should be equivalent. Please let me know what else I need to do. Fedora has been great on my Lenovo but this usb wlan stuff has been a pain.
[Code]...
I tried getting a Belkin USB Wireless adapter:N150 to work in a fresh installation of 10.4 with no success. After reading several forum posts I tried both solutions with ndiswrapper and the XP driver and with the Ralink native driver with no luck.
Code:
lsusb
Bus 005 Device 008: ID 050d:935a Belkin Components
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
i have ubuntu 10.04 i believe and i cant connect to the intenret i guess its not detecting my wireless adapter. i cant try ethernet cord which prolly would work because i cant move pc to another room....is there any fix for this? i googled linux drivers but i cant find any...i do have the cd that came with the adapter.
View 1 Replies View RelatedI have a Belkin F5D6050 adapter, which (despite being only 11b) was working better than my 11n adapter on 11.1 [The 11n stopped working today after I ran an upgrade; I have got it working - in a fashion under 11.3 - see RTL819SU not working with ifup (needs ifup-dhcp first)] I can't connect to my AP. The significant output from dmesg appears to be:
Code:
[19991.327361] wlan1: authenticate with 1c:af:f7:26:01:bc (try 1)
[19991.524037] wlan1: authenticate with 1c:af:f7:26:01:bc (try 2)
[19991.724034] wlan1: authenticate with 1c:af:f7:26:01:bc (try 3)
[19991.924031] wlan1: authentication with 1c:af:f7:26:01:bc timed out
FYI the info from
[Code]...
I'm trying to set up a new Dell machine with openSUSE 11.1 and KDE 4. For the rest of my PCs I use a Belkin kvm that connects the mouse and keyboard into PS/2 ports and it works. However, the new Dell doesn't have PS/2 ports and I can't get the machine to detect the mouse and keyboard (at all) unless I plug them in directly.
I'm using a Belkin four-port kvm, model number F1DJ104P. Does anyone know of a driver I could download to my Dell PC that would detect the devices via the kvm? The Belkin web site seems to be in pieces and is absolutely no use.
Alternatively, since I'm not particularly attached to the kvm, can anyone suggest a kvm switch that I could buy instead? It would have to have a minimum of four ports and be able to handle both Windows and Linux (all flavours with both OSs) machines, with both usb and PS/2 ports for mouse and keyboard. If it could handle audio, then that would be an improvement on what I've got already.
