Ubuntu Networking :: Can't Connect To Belkin N1 Router
Jun 23, 2010
I have a new belkin N1 router which I tested in somebody else's flat. It worked fine. When I got home I reset it by pushing a paperclip in the hole for 10+ seconds to erase this flat's internet connection settings (username and password and stuff). After this I plugged it the computer and tried to connect to it (wired connection) using 192.168.2.1 (this is correct for that router, it is not 192.168.0.1). But the browser says it is offline and cannot connect. The lights of the router cycle, the "modem router" light blinks continuously and the others briefly come on and go off again, every few seconds. I tried resetting it again, several times, leaving it off for a few hours, leaving it on for a few hours, etc.
View 2 Replies
ADVERTISEMENT
Jun 20, 2011
I have just installed 11.04 alongside windows vista. I have been trying to connect my router but it keeps saying disconnected from network. I have ran all of the troubleshooting tips in ubuntu its self and everthing seems in order. is there any settings i need to change on my router or in ubuntu's edit connections programe? I managed to connect to the router once to upgrade from 10.10 to the 11.04 but even before upgrading to 11.04 i had problems connecting to the router.
View 6 Replies
View Related
Apr 13, 2010
Because of the configuration of my house, I need two routers.I have a DLink ADSL router as my main router and the Belkin N1 as my repeater.I have set up the IP address in the Belkin to be 10.1.1.10 - my DLink is 10.1.1.1. I have disable the dhcp in the Belkin and set the DNS as ISP provided. [URL]..I have set the channel to 11 and in the Ubuntu Network Manger I have set the IPV4 to Link Local Only. I can see the Belkin and connect with my PC.but it will not take me through to the internet.
View 9 Replies
View Related
Jun 30, 2011
I have a Belkin wireless router model F5D7234-4 version 5. I switched to DHCP long enough to access the router via Firefox browser and look at all the settings. I turned off all encryption and other security related functions in order to just get it going. The IP of the router is 192.168.2.1 which is the default for this router. It is set to channel 6. I can not ping the router from either of two machines using regular ethernet or wireless. I have very limited experience with routers and am in need of help so I can use this for wireless connection to my living room box to my laptop in the bedroom about 50 feet away.
I tried changing the gateway from the living room box IP number to the router IP number with no success. I don't have anything connected to the internet port on the router. The living room box and the laptop are connected to the ethernet ports on the router. Ethernet works fine. Wireless does not. I compiled and installed the drivers for my wireless card on the laptop, a Realtek 8176 which uses the kernel modules rtl8192ce, rtlwifi and mac80211. ifup wlan0 brings up the wlan interface with these modules loaded. Right now I just want to be able to ping the router using regular ethernet. That would tickle me pink at this point. I downloaded the manual but I just can't seem to make headway.
View 2 Replies
View Related
Jul 8, 2010
I have a newer Belkin N+ router that has a USB port for accessing an external hard drive.I can access the HD with no problem in Windows.I am new to Linux/Ubuntu and cant seem to connect to the HD. In "Network" I have a folder "Windows Share" and within that folder is where I see the HD "CBHD" (name of my drive). I cant click it because when I do, i get an error message along the lines of (cant remember exactly right now) "Failed to mound"I typically access the drive in Windows via : \192.168.2.1
View 1 Replies
View Related
May 10, 2011
You'll need to reply like I'm an absolute idiot. I cannot get the stupid thing to work. WINE won't install, and I'm really confused on how to make it work. If anyone could please give me a step-by-step, that would be great.
View 1 Replies
View Related
May 13, 2010
Does anyone have an opinion on the BELKIN F5Z0142uk Enhanced Wireless ADSL Router Network Kit, I want to setup a small home LAN and this kit caught my eye, it includes a usb Wi-Fi dongle for connectivity to a desktop computer, one of my pc's doesnt have a network card so this sounds like a good idea. Whats the build quality like and is it reliable. The link: [URL]
View 2 Replies
View Related
Jun 21, 2010
I have an external hard drive connected to my router. From Windows I can access it, but from Ubuntu I can see the hard drive, but when I try to access, I'm asked for a password. However my network does not have a password neither the hard drive.
What must I do?
View 9 Replies
View Related
Dec 28, 2010
I recently purchased a TPlink 5 port switch, which for some reason didnt work with windows, only my ubuntu computer, I found a cheap wireless belkin router which also has 4 wired ports. It now works well except that it is slow searching for new servers eg, going to facebook creates a long wait and can even time out but once on the website everything works fast, The connection is 2.89 Mbps which is good for this area and ping is 45ms. What could I do to fix this problem. This affect my ubuntu computer and the windows xp pc as well
View 2 Replies
View Related
Mar 5, 2011
I'm having a slight problem with my new wireless card that I purchased. I installed the firmware and the like and it does work, my computer recognizes it and I can search through my available networks, only thing is though.I cannot connect to any of them. I'm fairly sure it's a problem with it obtaining an ip address though.because it does connect briefly and I read the status and it shows no IP address, but when I connect through wired internet all that information is available. I tried setting my network configuration to static and that didn't help at all. I'm only a week into Ubuntu so this is all still fairy confusing for me.
View 1 Replies
View Related
May 4, 2010
I have been trying to get my Belkin FD8233-4v3 wireless-n usb adapter to work in Ubuntu since 8.04. It has worked with ndiswrapper under 32-bit (never the 64-bit) versions in the past, but has never been able to be configured directly. It uses the Ralink RT2870 chipset, but cannot seem to be configured using the drivers from the Ralink website.
With Ubuntu 10.04 64-Bit, everything has changed. I have high hopes that this adapter may finally work correctly and without ndiswrapper. As soon as I first booted 10.04, for the first time ever, Ubuntu recognized the IF automatically, reported my wireless router, allowed me to enter my 128-bit WEP hex code and tried to connect up. It is failing miserably, but it is making a valiant effort.
View 4 Replies
View Related
Jun 15, 2010
I was dual booting with XP and Jackalope using a Belkin N wireless USB. The install on Jackalope was simple, a plug and play type situation, plugged it in and it worked. A few days ago though, i wiped the whole computer and installed Lynx. To my dismay, even though Lynx sees the wireless, sees the available signals, lets me input my password... it fails to connect. It just spins and spins and eventually asks for my password again...
I'm still pretty new to Ubuntu, and Linux in general. I updated, and pretty sure i retrieved 3rd party drivers for the video card properly (using a cable connection), but thats pretty close to where my "expertise" ends.
View 9 Replies
View Related
Feb 20, 2011
I'm using a Belkin F7D1101 USB adapter for my wireless internet, and I can't get the damn thing to connect. I've installed ndiswrapper, ndisutils, and ndisgtk, then used the latter to install the driver that came with the CD (though I'm sure I'm using the right one, I've tried all the included drivers with no success). The adapter itself is functioning fine, as I've used it on Windows XP with no issues. It's just not communicating with Ubuntu very well. My issue isn't that I can't get it to show up and search for a network (as I've seen on several other posts about this adapter), but that I can't get it to actually connect to my router. Using WEP 40/128, I enter the password, but after about a minute, I'm simply prompted for the password over and over. I've restarted several times, even installed 10.04 just because I had no idea what to try, and no dice.
View 2 Replies
View Related
Sep 22, 2010
I am using the Belkin wireless g usb adapter f5d7050 v1000 or at least that is what ubuntu says when I lsusb.
Code:
ceegee@Valar1:~$ lsusb
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 019: ID 050d:7050 Belkin Components F5D7050 ver 1000 WiFi
[code]....
View 2 Replies
View Related
Nov 6, 2009
I have a desktop PC running Ubuntu 9.10 and Windows 7, and a Eee PC 701 laptop running EasyPeasy Ubuntu 9.04. I'd like to connect the desktop to the laptop with a wired connection (eth0), then the laptop to my ADSL router using wireless (ath0).
I have a crossover ethernet cable (I bought on ebay). I have set up my laptop with a static IP address on my LAN and it uses OpenDNS.
I have added this to /etc/sysctl.conf on the laptop:
net.ipv4.ip_forward=1
Then I tried this on the laptop:
sudo iptables --table nat --append POSTROUTING --out-interface ath0 -j MASQUERADE
sudo iptables --append FORWARD --in-interface eth0 -j ACCEPT
This is a variation on what I found on other sites describing how to set up a router. I don't understand iptables very well, but I gather that the above two lines should set up forwarding so that traffic from my router to the laptop will be forwarded to the desktop, and vice versa.
But this doesn't work. The connection doesn't even establish between the laptop and the desktop.
View 12 Replies
View Related
Mar 9, 2011
I've just literally gone out this morning and bought the Belkin N300 Dual Band USB for my Deskstation running Maverick Meerkat. At first i put the stick in and nothing happened. So i went to System>admin>Windows wireless drivers and clicked on there. I put the CD in the drive that came with the dongle and found the drivers folder on the disk. I then installed the .inf file in the XP folder. It connected straight away as easy as that.
I'm really frustrated though as it loses conectivity and then asks me for my WAP password on connection, but then doesn't seem to connect. I unplug the dongle and then hit connect again and it connects.
If i use the same dongle on XP i have no problems what so ever, so i know its not a signal strength issue.
View 8 Replies
View Related
Apr 6, 2011
I am trying to setup a dhcp server for my internal network. I have two NICs, a modem, and a wireless router. I have my server connected directly to my modem which is providing me with Internet access on eth1 and is working fine. I have dhcp and dns setup on eth0 which is connected to my router. The router shows that it is connected to the Internet but when the router gives a client computer an IP address, the client is unable to connect to the Internet but can connect to the router. I will post my configuration files below with my current configuration.
[Code]....
View 5 Replies
View Related
Jun 18, 2011
I joined this forum so I can say my experience with the crappy belkin N150 router. It appears you need to run the setup cd under windows to make the router 'see' the modem. Under linux as someone pointed out you can easily enter the router setup from a browser ( enter 192.168.2.1 ) and connect to the router only (wired or wireless connection) but not the internet. Does anyone have any idea what the windows setup is doing to connect the router to the modem and how to do it under linux in the browser?
View 9 Replies
View Related
Feb 13, 2010
How do I get my ubuntu 9.04 computer to recognise the USB wireless stick and then connect to my wireless d_link router?
View 1 Replies
View Related
Oct 5, 2010
Ubuntu 9.04.
Belkin Wireless G router.
Has been working fine. Today it is not. I have done nothing to it. It just keeps saying "Looking up *********" and "Cannot connect to server".
I hard wired the pc to the modem and it works fine. Hard wired the pc to the router it works fine. Running wireless, both of my computers are not connecting.
If I remember, one of the lights on the router should be lit solid, just as it is on the modem. However, all lights are blinking. The only solid light is "power".
View 2 Replies
View Related
Sep 27, 2010
Last night I jumped into the linux world and finally installed Ubuntu in a dual boot system with XP on board as well (eventually I want to get rid of this). How can I get my wireless Belkin F5D8233-4 router working. I put the install disk in and it shows on the desktop but unable to execute - keep getting an error message. Getting frustrated...
View 6 Replies
View Related
Oct 2, 2010
I have a old laptop Dell C600 PIII 800mhz 256mb RAM 20Gb HDD and a floppy drive. It has 1 USB port and no wifi card.
I bought the Belkin F6D4050 v1 usb wireless adapter so that I could use it on the above laptop and connect to my wireless network at home. The Belkin USB wireless adapter has a Ralink xchipset
There was no specific Linux driver available but a workaround for an old driver worked. Some changes to the code and compiling gets the wireless adapter to work.
I have installed Arch on the laptop. I compiled it and its working fine
Questions 1.Arch linux releases new image only once or twice a year I have downloaded the latest available arch image and built froms scratch. When I update Arch (as it is a rolling release) the kernel also gets updated and the compiled driver fails to work. I have to recompile again for the new kernel. Is there a way I can compile this driver in the existing Arch or any other distro kernel and use as long as I can without updating so I do not have to recompile again
View 1 Replies
View Related
Apr 29, 2011
I plan on installing a belkin wifi router. Is there any software to configure it ? also i need to increase the security as max as possible will my wifi be secure? only certain number of devices to access it also any software to display the number of devices accessing it like a radar? i am very fed up of all the command-line thinggy
View 1 Replies
View Related
Aug 1, 2010
My son lost his USB Wireless stick for his Computer. I had thought I heard that if you had a second wireless router, you could use it somehow to detect the wireless router you have already set up in your home (like using a wireless card)? Is this what Ad-Hoc is? Either way, can this be done and if so how? I use a WRT54Gx2 Lynksys router and have a TRENDNET TEW-432BRP wireless router and also a spare D-link DI-514. I use ubuntu 10.04, and also wanted to know if I connected one of the router to his on the LAn port could he connect msaybe through an Ad-Hoc on my local computer here? He uses XP on his. I'm a newbie to linux and networking in general.
View 2 Replies
View Related
May 14, 2010
Code:
*-network
description: Ethernet interface
product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
[Code].....
I've read around blacklisting but I'm not sure on what I should be blacklisting really.
View 9 Replies
View Related
Feb 5, 2010
My problem is little different then what I've seen here. I get the same message after inputting network name and password. I click connect and it just pops up again I don't get it. I'm running Ubuntu 8.10 for Ppc (PS3) I get no internet connection what so ever just the same message. The message I get is " authentication required by wireless network " What do I need to do to connect wireless to my router with my PS3 using Ubuntu 8.10? It does connect with a Ethernet Wire. I am new with Linux.
View 1 Replies
View Related
Feb 6, 2010
I have a router with 2 IBM Thinkpads connected. One Thinkpad is running Ubuntu, and the other is running XP.
They connect to the router with no problems.
I installed Ubuntu on a Sharp Moebius laptop and plugged in the network cable.
NOTHING.
I have tried pinging the laptop; nothing.
I am not sure where the problem is, because my Thinkpads have no problems connecting to the router, with both Ubuntu and XP
View 9 Replies
View Related
Apr 22, 2010
my LAN just suddenly stopped working. we had a power outage, and it just stopped. it will still recognize the network, but it wont connect. i was experimenting with setting up a web server (trying to set it up on the standard distro). i know its not the network card (on board) because i can put in my pci card and it still wont connect. it will connect when in the live environment. i thought that maybe it had updated, so i tried to boot from a different (older) kernel. that still didn't help.
i stopped apache. i was experimenting with portforwarding at the time (i had everything else working on my server), but i could not get it to work. after this happened, i restored the original settings on my router. i had applied the settings only a day before the power outage. everything still works on another computer on the network (also running linux). (all computers run 9.10) its almost like my router won't assign me an ip address.
View 9 Replies
View Related
Sep 5, 2010
I recently just upgraded my operating system to Ubuntu 10.04 LTS and I can't seem to get my wireless card to connect to our new Verizon Actiontec router. I am using an Encore Electronics 802.11n Wireless USB Adapter (model: ENUWI-N), which had worked with an earlier version of Ubuntu and our old router. The adapter recognizes the SSID of the new router but will not connect with the correct WEP key or even with the encryption turned off. I have tried deleting the wireless profiles and manually re-creating them and still no dice. I have also gone to the website of the chipset manufacturer and found the latest drivers (RT2870USB(RT2870/RT2770)) for the adapter, which, according to the Synaptic Package Manager, I do not currently have installed.
Where do I go from here? Do I need to install the new drivers, and if so how do I do that?
View 6 Replies
View Related
Oct 23, 2010
I wanted to try Ubuntu again but have gone wayback to an old 8.10 disk because I couldn't get 10.10 to work. The install with 8.10 went fine but the internet will not connect. The network manager shows eth0 grayed out and when going in to manage the connection it says 'never'. I'm using Vista with a broadband modem connected to a netgear router.
View 3 Replies
View Related
