I bought a x-kim gptl-00c gamepad and when I plug it in it is not recognized.
The dmesg read out is
[ 2173.516017] usb 5-2: new low speed USB device using uhci_hcd and address 63
[ 2173.928012] usb 5-2: device not accepting address 63, error -71
it is not detected from lsusb
[Code]...
I am working on an embedded system, which is an USB MSC device that supports some vendor specific scsi commands. I am using FC10 laptop as USB host for testing, and it runs some small apps based on sg3. All has been well for ~ a week. The FC10 laptop is able to communicate with the device and retrieve data. Suddenly, starting from today, the laptop is not able to properly detect the device. When plugged-in, the MSC device is detected as input device (I thought). This is observed from "dmesg" output and changes in "/dev/input/".The device under development is running at full speed. When I connect to winXP, no problem. A windows file explorer pops up, showing the content of the drive.Also, the FC10 has no problem with other USB flash drive (high speed).
View 1 Replies View RelatedI have freshly installed ubuntu 9.10 and moreover i am completely a newbie to Linux. The problem now i am facing is, i am not able to configure my wireless router. I tried finding drivers for it in System->administration->hardware drivers. But it showed me none. Then i checked out one of the threads in this forum and came across the 'lspci -nn' cmd. This gave me the info abt my wireless network controller and it was : 'Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01)'.
View 1 Replies View Relatedsome days ago I upgraded to Ubuntu 10.04 and now I have a problem with my webcam. I like to use chatroulette and mebeam, therefore I have to use programs like webcamstudio/flashcam... (Flash does not accept the normal cam device v4l2 and webcamstudio puts it to v4l loopback). The problem is that Ubuntu is detecting only v4l2 and not v4l, so that I don't have an output device in webcamstudio.
When I type:
ls -l /dev/video*
the answer is only:
crw-rw----+ 1 root video 81, 0 2010-05-08 17:59 /dev/video0
and nothing more
how I can create a second video device for flash.
I have tried connecting an LG GD330 mobile in both "Mass Storage" & "Data Service" but in either cases it does not appear in bansheee nor even in rhythmbox.
View 6 Replies View RelatedI'm trying to install 11.04 onto a custom build pc.I have burned an install CD of the desktop edition and have inserted it into the drive, started up, and tried to run the live version. IT pops up, everything works, Hooray! I go to install it to disk and I follow all the prompts and it needs me to reboot to start. YAY! I click to reboot, remove the CD as requested, and then I get the "No Boot Device Detected!" error message.
I then tried installing straight from the CD and not booting into the live version. I follow all the steps and get a congratulations on installing it and all I need to do it reboot. I remove the CD, reboot, and BANG! the same message. I'm not sure what's up or even where I can get information from because there is no BIOS splash screen or anything to naviagate through.
System Specs:
Intel Atom Mobo/Proc (1.66Hz)
8GB Corsair RAM
1 slim optical drive (SATA)
1 2TB Seagate HD (SATA)
1 Case/PSU combination
EDIT1: Currently I am checking the live CD for defects (though it has an internet connection so I'm unsure whether the CD matters).
I have a Epson Stylus SX115 All In One Printer which i connected to ubuntu 9.10 the other day. Upon installation the drivers for the stylus SX 115 were not available, but there were drivers for the stylus SX110 which i then installed. Printing is fine although for some reason even though i connect via usb cable the printer is not detected as a external device. I have to pull out the usb cable without unmounting-what should i do?
View 8 Replies View RelatedI am new to linux having just abandoned Windows due to stability issues. I have a Hauppage remote with a usb ir receiver. This worked fine under windows using the drivers for the windows media center remote. I can't however get this to work under Linux. What I am really looking for is a method, perhaps using a command line in the terminal window to be able to test and see if the OS has actually detected the device. I have tried irw, but there is no response. If I know that the device is connected, then I can start looking at issues of identifying the correct drivers for the device.
View 6 Replies View RelatedI'm using ubuntu 10.04 enterprise cloud server for my project. I use USB NIC to interface with other 2 servers. but the system doesnot detect USB NIC. detect & configure USB NIC in the network.
View 5 Replies View RelatedAfter plugging in my mp3 player to usb it isn't detected, even though it powers up and charges. I do an fdisk -l and nothing. My lspci shows the controller and my mouse is detected. lsusb shows the Phillips gogear as the device and it is device 2. I did dmesg and at the end it showed
scsi 6:0:0:0: Device offlined - not ready after error recovery
I don't know if this is the issue or not but it's the only error I get, so I assume it's the problem.
I have a usb PlayStation-gamepad (Trust GM-1520) which I would like to get a readable output from. I run hexdump and od got a bunch of numbers. How can I get which button(s) is active and the position of the joystick(s)?
View 1 Replies View RelatedRecently xsane has stopped detecting my MFP (HP Deskjet F2280). My setup has not had any hardware changes and the only software changes in that time have been the periodic Synaptic updates. Before this hiccup all had been well for over a year. If I run xsane it thinks a while (10 sec?) and tells me in a little panel no devices were detected. If I run lsusb, it finds the device, but after all it is a printer/scanner and the printing function continues to be OK so this is not a surprise.
I do not know enough to understand all the lsusb output to know if anything is amiss in the detail. What is it that xsane needs so that it detects the device as a scanner? Is there a file or specific stuff in a file which I could get from an old backup or edit (carefully!) by hand? I don't need the scanning function often enough to pin down what might have done the mischief.
I have purchase one Lenovo L420. It has Windows 7 installed. I have installed Ubuntu 10.10 also (dual boot). The wireless is not working in Ubuntu but working in Windows 7. I think that the wireless device is not detected in Ubuntu.
View 9 Replies View Relatedi am trying to use my logitech gamepad as a mouse using js2mouse. It is not working.
i am running suse 11.2
I have downloaded and installed js2mouse with no errors. when i run it i get:
# js2mouse
Number of axes : 6
Number of buttons : 12
Driver version : 131328
Joystick name : Logitech Logitech Dual Action
[Code].....
i dont get any errors form the terminal, but it does not work.
I have an nc8000 that gives a "104 unsupported wireless network device detected" error when I plug in my Intel wifi card that I acquired recently. Based on reading, this is a common HP problem due to non-native HP hardware. If I insert the Intel Pro card after the HP boot screen, 10.04 loads just fine and Ubuntu detects the card.
1) Machine Brand and Model (PC/Laptop): HP/Compaq nc8000
2) Wireless Brand, Model and Wireless Chipset: 02:04.0 Network controller: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network Connection (rev 05)
3) Check interface:
lo no wireless extensions.
eth0 no wireless extensions.
irda0 no wireless extensions.
eth1 unassociated ESSIDff/any
4) Check for modules:
Code:
Module Size Used by
binfmt_misc 6587 1
snd_intel8x0 25588 2
snd_ac97_codec 100646 1 snd_intel8x0
ac97_bus 1002 1 snd_ac97_codec
fbcon 35102 71 .....
5) Network configuration
Code:
$ *-network:0
description: Wireless interface
product: PRO/Wireless 2915ABG [Calexico2] Network Connection
vendor: Intel Corporation
physical id: 4 .....
6) Scan for networks:
Code:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
irda0 Interface doesn't support scanning.
eth1 No scan results
7) Ubuntu Version:
Code:
Ubuntu 10.04 LTS
8 ) Kernel/architecture (including 32 vs. 64 bit):
Code: 2.6.32-21-generic i686
I have just installed the last FC distro, and everything works good, except the wireless network.I have a Linksys N-Ultra WirelessN USB wifi card, model WUSB600N.It uses the rt2x00 driver, concretely the rt2870 driver (at least, thats the driver included in the original device drivers CD).Right now, the problem is that i don't know how to make my Fedora 12 to enable and/or connect to internet.
dmesg | tail
usb 1-3: Manufacturer: Cisco-Linksys LLC
usb 1-3: configuration #1 chosen from 1 choice
[code]...
My onboard bluetooth is not being detected by SUSE 11.4. Fedora 14 has no problem detecting the hardware, but it just doesn't show up in SUSE 11.4. I have included a few outputs:
lsusb:
Code:
Bus 008 Device 002: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth
rfkill list
[Code]....
If I plug in a dongle, the Bluetooth icon shows up in the notification bar, and I'm able to add and remove devices normally. Is there support for my onboard bluetooth device?
I installed 11.1 when it first came out. The PC I used gave up the ghost and I bought a refurbie, HP xw4100 and installed the 11.1 drive in it. All works except Internet connection. I am befuddled, bemused, confused and at a complete loss! The router on USB is not detected.
Boot Time - Status blinks, LAN is OFF and remains OFF. DSL blinks several times.
Booted - Status continues and DSL blinks.
YaST (NetworkManager is useless)
Network Devices - DSL
Config Overview
- DSL Devices - Not detected
- Add - PPP over Ethernet
Mode Dependent Settings
- Ethernet Card
- DS: Connection - Unknown - No IP address assigned
- Configure Network Cards = On Hotplug
Network Settings
- Enable IPV6 (as previously set)
- DHCP Client Options - left blank
Overview
- Unknown Device
- IP Address - Not configured
- Unknown Network Device (no hwinfo)
Edit
- Dynamic Address - Zeroconf
Next
- Loop back to Overview - Unknown Device
I have a problem here where sane no longer detects my scanner.
Code:
lsusb
reports
Bus 007 Device 002: ID 03f0:5b17 Hewlett-Packard
Code:
sane-find-scanner
reports:
found USB scanner (vendor=0x03f0 [Hewlett-Packard], product=0x5b17 [HP Color LaserJet CM2320fxi MFP]) at libusb:007:002
Code:
scanimage -L
reports
No scanners were identified. xsane reports no devices detected (I have it in French, "Aucun p'rif'rique disponible"). I get the same when I launch xsane as root, so I doubt it is a usb-rules issue. It used to work; I checked /proc/bus/usb, but that is empty.
I am trying to install dynabolic on my system by docking.I copied dyne/ directory into my partition and updated grub as follows:
title Dyne
root (hd0,0)
kernel (hd0,0)/dyne/2618ckld.krn root=/dev/ram0 rw load_ramdisk=1 prompt_ramdisk=0
ramdisk_start=0 max_loop=64 vga=788
initrd (hd0,0)/dyne/initrd.gz
Still on booting into it,it is saying "No storage device with dyne system found"
why this happens? On the otherhand it is automatically detecting my pendrive in which i have copied dyne/
and boots from it.
When I run the audio configuration I get:
The following audio device was detected:
Vendor: nVidia
Model Coporation GF100 High Definition Audio Controller
Module snd-hda-intel
but I do not hear sound.
The ALSA driver version is 1.0.14rc3
Lib package is: 1.0.17.-1.e15
Utils package is: 1.0.17-1.e15
The sound log has:
class: AUDIO
bus: PCI
detached: 0
driver: snd-hda-intel
desc: "nVidia Corporation GF100 High Definition Audio Controller" .....
The audio configuration sound test and the answer to the question No returns a message that says: automatic detection of sound card did not work. I am not sure what else is needed to diagnose the problem.
I am new to Linux and after a lot of research I settled on CentOS to be my OS for Linux. But I am having trouble with sound right now as I can not play audio. The command system-config-soundcard opened a gui for audio configuration saying following device is detected - Intel Corp. 82801(ICH9 Family) HD Audio Controller.
Ouput for some commands are given below::
[root@localhost ~]# lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) .....
[root@localhost ~]# uname -r
2.6.18-164.el5
[root@localhost ~]# cat /etc/redhat-release
CentOS release 5.4 (Final)
Clicking on the volume icon gives me message that either Gstreamer plugins are not installed or sound card is not configured.
While Trying to install gstreamer using YUM, I got following message:
[root@localhost ~]# yum install gstreamer
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile .....
Setting up Install Process
Package gstreamer-0.10.20-3.el5.x86_64 already installed and latest version
Package gstreamer-0.10.20-3.el5.i386 already installed and latest version
Nothing to do
[root@localhost ~]#
So I guess gstreamer are installed but how to configure the sound card or is there any other problem.
I have bought a generic gamepad from China quite a while ago, which worked well on Windows XP (it's HID-compliant). However, after finally being able to switch back to OpenSuSE, I now find that I can't get it to work.
I am currently running OpenSuSE 11.3, with GNOME. I've used the "modprobe joydev" command, and if I run lsusb, I get the following:
Code:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID eb1a:2571 eMPIA Technology, Inc.
Bus 001 Device 005: ID 058f:6362 Alcor Micro Corp. Hi-Speed 21-in-1 Flash Card Reader/Writer (Internal/External)
Bus 001 Device 006: ID 0c0b:b136 Dura Micro, Inc. (Acomdata)
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID e0ff:0002
Bus 002 Device 003: ID 06a3:8021 Saitek PLC Eclipse II Keyboard
Bus 002 Device 004: ID 0079:0006 DragonRise Inc. Generic USB Joystick
The last one is my gamepad, and it's apparently pretty well-known. I have also tried the "cat /dev/input/js1" trick, and it does indeed show garbage when I press buttons or move the analog sticks, so in fact it should be functioning properly. However, I can't get it work. In Tux Racer it simply doesn't recognize any joystick/gamepad, and Racer (the simulator) tells me that 0 joysticks have been found.
I have been searching for a solution for quite a while now, but all topics seem to be outdated (older OpenSuSE versions, listing commands that don't exist and are nowhere to be found...)
how to get this gamepad to work? Even if it means without the analog sticks, if it at least works a bit (I'll just do without the vibration, which is apparently very hard to get to work under Linux).
I recently installed Arch Linux on an old desktop machine. Everything works well except the onboard audio isn't detected at all.
I am using the 2.6.32-ARCH kernel
My lspci output is:
Code:
# lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] SiS645DX Host & Memory & AGP Controller
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
[Code]....
On another note, the manufacturer (ASUS) actually provides Linux audio drivers for my motherboard (model: P4S533). I attempted to install them, but the configuration process involves using make menuconfig, make xconfig, or make config to add the drivers to the kernel (I think) and I'm still a relatively new Linux user and had no clue what I was doing.
I upgraded from 11.2 to 11.3 yesterday, using a 64-bit Dell 1535 laptop.
With the new version, I find that the Device Notifier no longer detects my mp3 player through any of the USB ports. Neither does Dolphin.
Similar threads that I've read through have not done the trick.
I have a Logitech Wireless Gamepad F710 that I'd like to be able to use as a remote control for a media player on my PC. I currently map the gamepad to certain hot-keys for use with VLC, but I can't say it's ideal.Is there a media player out there that's easy to control with a gamepad and supports a wide range of file types?Bonus points if it has an internal video library.
View 2 Replies View RelatedThis device doesn't automount, doesn't show in KDE 4's device notifier, and I can't mount this camera manually because it doesn't appear to get assigned to a device node. Any known solutions? It worked in Slackware 12.2, but not in 13.0 or 13.1.
View 2 Replies View Relatedi am having dell inspiron 1540 laptop installed with ubuntu 10.04 (updated). i wanted to install LAMP(Linux,Apache,MySQL,PHP) for software development purpose.
but after restarting the system, following things occured:-Message box appears saying "Ubuntu is running in low-graphics mode" Your screen, graphics card and input device setting could not be detected... OK
Then i get prompt saying what would you like to do ?Run ubuntu in low-graphics mode for just one session.
i get a message starting display in one minute.....nothing happens ... i switch to text mode by pressing
escape. There is a brown color star before: Speech dispacher configured for user sessions.on battery state there is a infinte loop i.e. no response and system just hangs there...startx at text mode makes the screen blank...
Please tell which part of '/var/log/Xorg.0.log' sholud be scanned to find required information.
i am a new to ubuntu How to solve this problem i donot have internet connection and its important that i get it repaired as soon as possible....essential to get it running else i will be forced to goto Windows...
I have recently installed fedora 15, I'm trying to connect my mobile phone to my laptop through bluetooth, when I did setup new device it is just showing device address and (instead of name), and the forward button is not enabled..FYI - I have started and enabled the bluetooth services using systemctl
View 9 Replies View RelatedI tried to install OpenSuse 11.3 on my brand new pc, which already had Windows 7 proffessional in it, and I went step by step through the installation without changing anything. It didn't work. I tried for a second time and this error message kept popping up: "Creating device modes with udev 2.0436224] [drm: i915_diver_load]*ERROR*Detected broken BIOS with 262140/2644kb of video memory stolen. 2.0436224] [drm: i915_diver_load]*ERROR*Disabling GEM(try reducing stolen memory or updating the BIOS to fix)"
And then a lot of letters and numbers wich make no sense to me. Now the only way I can initiate OpenSuse is with the OSuse boot dvd and on failsafe mode.