Ubuntu Networking :: NC8000 - 104 Unsupported Wireless Network Device Detected

May 6, 2010

I have an nc8000 that gives a "104 unsupported wireless network device detected" error when I plug in my Intel wifi card that I acquired recently. Based on reading, this is a common HP problem due to non-native HP hardware. If I insert the Intel Pro card after the HP boot screen, 10.04 loads just fine and Ubuntu detects the card.

1) Machine Brand and Model (PC/Laptop): HP/Compaq nc8000

2) Wireless Brand, Model and Wireless Chipset: 02:04.0 Network controller: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network Connection (rev 05)

3) Check interface:
lo no wireless extensions.
eth0 no wireless extensions.
irda0 no wireless extensions.
eth1 unassociated ESSIDff/any

4) Check for modules:
Code:
Module Size Used by
binfmt_misc 6587 1
snd_intel8x0 25588 2
snd_ac97_codec 100646 1 snd_intel8x0
ac97_bus 1002 1 snd_ac97_codec
fbcon 35102 71 .....

5) Network configuration
Code:
$ *-network:0
description: Wireless interface
product: PRO/Wireless 2915ABG [Calexico2] Network Connection
vendor: Intel Corporation
physical id: 4 .....

6) Scan for networks:
Code:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
irda0 Interface doesn't support scanning.
eth1 No scan results

7) Ubuntu Version:
Code:
Ubuntu 10.04 LTS

8 ) Kernel/architecture (including 32 vs. 64 bit):
Code: 2.6.32-21-generic i686

View 2 Replies


ADVERTISEMENT

Ubuntu Networking :: Wireless Device Not Detected In 9.10?

Jan 9, 2010

I have freshly installed ubuntu 9.10 and moreover i am completely a newbie to Linux. The problem now i am facing is, i am not able to configure my wireless router. I tried finding drivers for it in System->administration->hardware drivers. But it showed me none. Then i checked out one of the threads in this forum and came across the 'lspci -nn' cmd. This gave me the info abt my wireless network controller and it was : 'Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01)'.

View 1 Replies View Related

Ubuntu Networking :: 10.10 On Lenovo L420 - Wireless Device Not Detected

Jul 17, 2011

I have purchase one Lenovo L420. It has Windows 7 installed. I have installed Ubuntu 10.10 also (dual boot). The wireless is not working in Ubuntu but working in Windows 7. I think that the wireless device is not detected in Ubuntu.

View 9 Replies View Related

Ubuntu Networking :: Wireless Network Not Detected In 11.04?

Jun 26, 2011

I am using a Compaq presario laptop. I installed Ubuntu 11.04 (32 bit) within windows 7.Initially my WiFi was running fine in Ubuntu without me doing anything. Now suddenly Ubuntu has stopped showing any of the WiFi networks. I have not done any changes in Ubuntu.When i booted to my Win 7, it was able to detect the network. I uninstalled and reinstalled Ubuntu, with no avail. But Ubuntu is able to detect the wired network when connected. I am at a loss.

View 9 Replies View Related

Ubuntu Networking :: Wireless Network Not Detected After Wakeup?

May 15, 2010

I am using a Toshiba Satellite M200. Sometimes after a wakeup ubuntu does not detect any wireless networks. This does not happen all the time only some times but, when I restart my computer the wireless networks are detected.

View 2 Replies View Related

Ubuntu Networking :: Wireless Network Detected But Not Getting Connected

Aug 15, 2010

I've installed Ubuntu 10.04 32 bit version(dual OS) on my 64 bit Pentium core2 duo 2.2GHz processor. Everything seems to be working fine except it's not getting connected to wireless network, although it's detected the network .It was working fine(got connected to wireless network) when I had installed the same OS via virtual machine.

View 9 Replies View Related

Ubuntu Networking :: No Network Interfaces (neither Ethernet, Nor Wireless) Detected?

Mar 2, 2010

Problem:I got a new Acer Aspire 8935G notebook, installed Ubuntu 9.10 on it and everything is fine, except the fact, that it wont detect any network interfaces (or how to call it So there are no ethernet or wlan connections available in the network-manager..

lspci gives me following lines:
joe@IGNAZ ~ $ lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev

[code]...

View 9 Replies View Related

Fedora Networking :: Wireless Network Card Being Detected But Not Being Allowed To Activate?

Mar 7, 2009

I have downloaded and installed Fedora 10.Now I am setting up the network and in the 'network configuration' it finds the wireless device (ralink) in the 'hardware' section of the configuration - I set this to eth0 (it originally set itself to wan0 and I still had the same problems, now it doesn't give me the option to put it back to wan0).Now I goto the devices tab and try to set up the device with eth0 - which it seems to find.But when I goto activate the device it tells me that eth0 cannot be found

View 2 Replies View Related

Ubuntu Networking :: WG511 Wireless Card Not Available As Network Device

Feb 22, 2011

I have just installed Ubuntu 10.10 on a Dell Laptop. It has a Netgear WG511 (made in China) PCI wireless card but I cannot see any connections other than the wired one. Entering in lspci in the terminal mode and removing/replacing the WG511 shows (I think) that something is being detected in the PCI slot "Network Controller: Intersil Corporation ISL 3890 [Prism GT/Prism Duette]/ISL3886 [Prism Javelin/Prism Xbow] rev 01". Is this the WG511 and, if so, how do I get it to be detected as a network device?

View 9 Replies View Related

Ubuntu Networking :: 780i Network Unsupported In 10.10?

Dec 26, 2010

I have installed Ubuntu 10.10 in my desktop, and network doesn't work, are nForce 7 network cards unsupported in Ubuntu?

View 1 Replies View Related

Ubuntu Networking :: Error While Creating Wireless Network - Set Failed On Device?

Jan 16, 2010

I have been working on this for a while now and am absolutely stumped. Basically, what i am attempting to do is make my ubuntu box into a gateway for my network. I have everything working thru hard wire, but I simply cant get the wireless to work. No matter what I do, I cannot get my wireless card to transmit an essid and allow nodes to connect. I have tried assigning it in the interfaces file (shown below), and I have also tried manually modifying it using the iwconfig command. Here is the topology:

eth1: internet WAN
eth2: ethernet out to LAN
ra0: wireless out to LAN
Here is a copy of my /etc/network/interfaces file:
[CODE]
auto lo

[Code]...

View 2 Replies View Related

Ubuntu Networking :: Usb Wireless Device Not Shown Under Sudo Lshw -c Network?

Feb 5, 2010

Okay currently I am using a a Belkin F6D4050v1 usb wireless n card on a 32 bit intall of ubuntu 9.10. I have already installed ndiswrapper and installed the the rt2870.inf driver and rebooted. But i still have no wireless. when I use the command "sudo lshw -C network" all i see is my pci wired nic card"lsusb" the ID of the card is "050d:935a Belkin Components""sudo iwconfig" sayslo no wireless extensionsetho no wireless extensions

View 2 Replies View Related

Ubuntu Networking :: 'sudo Lshw -C Network' Can't Find My Wireless Device

Aug 7, 2010

I have a wired connection on the motherboard and a also a card for wireless communication.Wired connection works fine but my plan is now to setup wireless connection too.I was advised to use this in order to find installed network devices: sudo lshw -C network.Not sure, but I think it only reports details about the wired device. Is that correct?How could I get ubuntu to also find my wifi-card?

View 7 Replies View Related

OpenSUSE Network :: 11.1 - Router On USB Not Detected (Unknown Device)

Mar 10, 2010

I installed 11.1 when it first came out. The PC I used gave up the ghost and I bought a refurbie, HP xw4100 and installed the 11.1 drive in it. All works except Internet connection. I am befuddled, bemused, confused and at a complete loss! The router on USB is not detected.

Boot Time - Status blinks, LAN is OFF and remains OFF. DSL blinks several times.
Booted - Status continues and DSL blinks.

YaST (NetworkManager is useless)
Network Devices - DSL
Config Overview
- DSL Devices - Not detected
- Add - PPP over Ethernet
Mode Dependent Settings
- Ethernet Card
- DS: Connection - Unknown - No IP address assigned
- Configure Network Cards = On Hotplug
Network Settings
- Enable IPV6 (as previously set)
- DHCP Client Options - left blank
Overview
- Unknown Device
- IP Address - Not configured
- Unknown Network Device (no hwinfo)
Edit
- Dynamic Address - Zeroconf
Next
- Loop back to Overview - Unknown Device

View 6 Replies View Related

OpenSUSE Wireless :: Wireless Card Detected But Unable To Scan The Network

Oct 27, 2010

1 ) make and model of wireless device Athreos 5k

2 ) driver version in use dont know

3 ) any error message. -

abhishek:/ # sudo /usr/sbin/iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down

4 ) what you have tried to rectify the problem.

Tried to install all the patches.

5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies

6 ) openSUSE version 11.3

7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)

Subsystem: Hewlett-Packard Company Device 137a
Flags: bus master, fast devsel, latency 0, IRQ 23
Memory at c2000000 (64-bit, non-prefetchable) [size=64K]

[code]....

View 9 Replies View Related

CentOS 5 :: Reinstall The Guest Additions And Detected Unsupported X86 Environment?

Sep 2, 2010

Just installed updates with the recent kernel update 11.3 for Centos 5.5. I have had guest additions running fine before that. Now when I try to reinstall the guest additions (which is necessary) I get the message Detected Unsupported x86 environment. how to get this going since it was running fine before the kernel update.

View 7 Replies View Related

Fedora Networking :: Open The Network Device Control To Activate It But There Is No Network Ports In Network Device Control?

Jan 7, 2010

I just added a 2 port network card to a system that is running Fedora 11, but it is INACTIVE. I open the Network Device Control to activate it but there is no network ports in Network Device Control. It is empty.It looks like the system recognize the card and loaded correct driver.

View 4 Replies View Related

Ubuntu Networking :: Usb To Ethernet Device Not Detected / Enable This?

Jul 28, 2011

I'm using ubuntu 10.04 enterprise cloud server for my project. I use USB NIC to interface with other 2 servers. but the system doesnot detect USB NIC. detect & configure USB NIC in the network.

View 5 Replies View Related

Ubuntu Networking :: Wireless Network: "device Not Ready (firmware Missing)"

Jun 12, 2011

I have installed Ubuntu 11.04 on my laptop. For some reason Wireless Network does not work any more (there was installed 9.04 before).

lspci says:
Code:
00:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
System->Administration->Additional Drivers doesn't list anything.

View 9 Replies View Related

Debian :: Wireless Network Not Detected?

Aug 22, 2010

I just did a fresh install of debian (amd64) on my laptop (Dell Inspiron 1520). My wireless network is not being detected, but I'm pretty sure that my wireless device IS being detected. During the installation, I got a message about some firmware .ucode file not being found. It asked me to put the file on a usb stick (which I got online), and I did that. It didn't complain after that, but I got the same message again later on, but again it didn't complain when I continued the installation.

View 4 Replies View Related

Ubuntu Networking :: See The Phrase " Device Not Ready" Greyed Out, And Unable To Access A Wireless Network?

Oct 10, 2010

Everytime I to turn on my wireless device, and try to connect to a wireless network, i see the phrase " device not ready" greyed out, and not able to access a wireless network. i do not know what to do

View 6 Replies View Related

Fedora Networking :: Wifi Device Detected But Can't Connect?

Jan 21, 2010

I have just installed the last FC distro, and everything works good, except the wireless network.I have a Linksys N-Ultra WirelessN USB wifi card, model WUSB600N.It uses the rt2x00 driver, concretely the rt2870 driver (at least, thats the driver included in the original device drivers CD).Right now, the problem is that i don't know how to make my Fedora 12 to enable and/or connect to internet.

dmesg | tail
usb 1-3: Manufacturer: Cisco-Linksys LLC
usb 1-3: configuration #1 chosen from 1 choice

[code]...

View 4 Replies View Related

OpenSUSE Wireless :: Network Detected But Will Not Connect?

Feb 16, 2010

I have a D-link dir-635 firmware v. 2.30eu (latest) and a USB WLAN adapter D-link DWA-140 802.11n. The driver seems to be installed correctly since lsusb lists it correctly and all the wireless networks in the vicinity are detected including mine. When I try to connect however NetworkManager says it is activating but after awhile the windows with the newtork password appers. dmesg output:

[ 5509.487262] wlan0: direct probe to AP 00:1c:f0:71:03:88 try 1
[ 5509.684014] wlan0: direct probe to AP 00:1c:f0:71:03:88 try 2
[ 5509.884020] wlan0: direct probe to AP 00:1c:f0:71:03:88 try 3
[ 5510.084014] wlan0: direct probe to AP 00:1c:f0:71:03:88 timed out

So it is able to determine the AP:s mac address but each time it times out.

I have tried disabling the security on the router but no luck.

Not sure what to try next. I have checked some of the tips supplied in these forums but none seem to handle the issue I am having.

View 7 Replies View Related

OpenSUSE Wireless :: Network Detected But It Just Won't Actually Connect To It

Jul 17, 2010

an issue with my broadcom wireless that is using the bcm4312 driver. I installed the b43(?) cutter firmware from the command line and now my network is detected but it just won't actually connect to it. My router has wpa security enabled but i think it worked with it before.

View 9 Replies View Related

Ubuntu Networking :: Trendnet Wireless Detected, But No Wireless?

Dec 20, 2010

I recently bought and installed the Trendnet TEW423PI. Running ubuntu 10.10I downloaded ndiswrapper and it tells me:net8185 Hardware present: yesYet,cannot connect to the internet wirelessly.How do I go about setting this up?What do I need to type in the terminal

View 2 Replies View Related

OpenSUSE Network :: Network Manager Not Detecting Wireless Device?

Sep 25, 2010

Having a hard time getting NM to detect wireless usb device: Linksys model WUSB600N. Here are a few commands I do know about.

iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
irda0 no wireless extensions.

[code]....

View 9 Replies View Related

SUSE :: Wireless Card Detected But Can't Connect To A Its Network / Get It To Work?

Mar 14, 2009

Wireless card detected but cannot connect to a wireless network

I have install it suse 11, and everything went well until the wireless thing is not working, my card is Broadcom BCM4318, I see my card on the network settings but I cannot configure the card, and also I cannot connect to a wireless network, can someone tell me what to do here, I am loosing my patient....

View 4 Replies View Related

General :: Wireless Network Adapter Is Not Detected In Hp CQ40-416 Using Backtrack4?

Feb 19, 2010

I am a newbie in linux and I curious to learning all about linux, but I have a little trouble. I've just installed my first linux, its Backtrack 4 and my wirelesss network adapter was not detected..please help what I'm soppost to do..i'm using HP CQ40-416AMD Turion X2Broadcom 802.11 b/g WLAN Adapternote :

View 1 Replies View Related

Fedora Hardware :: Full Speed USB MSC Device Detected As Input Device?

Apr 7, 2011

I am working on an embedded system, which is an USB MSC device that supports some vendor specific scsi commands. I am using FC10 laptop as USB host for testing, and it runs some small apps based on sg3. All has been well for ~ a week. The FC10 laptop is able to communicate with the device and retrieve data. Suddenly, starting from today, the laptop is not able to properly detect the device. When plugged-in, the MSC device is detected as input device (I thought). This is observed from "dmesg" output and changes in "/dev/input/".The device under development is running at full speed. When I connect to winXP, no problem. A windows file explorer pops up, showing the content of the drive.Also, the FC10 has no problem with other USB flash drive (high speed).

View 1 Replies View Related

Fedora Hardware :: Wireless Network Adapter Not Detected - Dell Inspiron E1750?

Jan 4, 2011

today my windows crashed and i decided to move into Linux.But here comes my biggest problem now, i cannot connect to wireless network but i am able to connect through wired connectionmine is a 10 year old computer so i think the card used is Intel PRO/Wireless 3945ABGi am using Fedora 14. please note that i know only very little in Linux so please respond accordingly

View 14 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved