Hardware :: HP CM 2320 FXI Scanner And Sane - No Device Detected
Mar 6, 2011
I have a problem here where sane no longer detects my scanner.
Code:
lsusb
reports
Bus 007 Device 002: ID 03f0:5b17 Hewlett-Packard
Code:
sane-find-scanner
reports:
found USB scanner (vendor=0x03f0 [Hewlett-Packard], product=0x5b17 [HP Color LaserJet CM2320fxi MFP]) at libusb:007:002
Code:
scanimage -L
reports
No scanners were identified. xsane reports no devices detected (I have it in French, "Aucun p'rif'rique disponible"). I get the same when I launch xsane as root, so I doubt it is a usb-rules issue. It used to work; I checked /proc/bus/usb, but that is empty.
View 3 Replies
ADVERTISEMENT
Dec 6, 2010
I added myself to the scanner and saned groups, however scanimage -L only detects the device when run as superuser. I think this may be related to [URL].
root@icecream:/home/discord# scanimage -L
device 'epson2:/dev/sg0' is a Epson GT-9800 flatbed scanner
discord@icecream:~$ scanimage -L
No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages).
View 1 Replies
View Related
Jul 22, 2011
OS: CentOS 5.6 yesterday i bought a new HP network printer/scanner (OfficeJet Pro 8500). It installed correctly using hplip drivers. I can print and scan without any problem, very nice and fast device. I did some research where the information where the device port is stored in sane, but cannot find anything. I tried to remove my old network device port for my Brother scanner, but did not find the config file where this information is stored. Neither /etc/sane.d/* nor ~/.sane/xsane/* contains this information.
View 14 Replies
View Related
Mar 28, 2010
I have a Genius CP-SF600 scanner. I have put the fimware in the necessary directory for the backend (/usr/share/sane/gt68xx), and what I run sane-find-scanner I get:
Code:
$ sane-find-scanner
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
found USB scanner (vendor=0x0458, product=0x2021, chip=GT-6816?) at libusb:002:006
# Your USB scanner was (probably) detected. It may or may not be supported by
# SANE. Try scanimage -L and read the backend's manpage.
# Not checking for parallel port scanners.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.
However, when I run scanimage -L I get:
Code:
$ scanimage -L
No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). So sane sees the scanner, but then scanimage says it can't find any scanners. If I run scanimage -L as root it does seem to find the scanner.. so its a permissions problem somewhere.. I will keep investigating....
View 2 Replies
View Related
Mar 24, 2011
I have a Samsung SCX-4200. It was working pretty good with sane 1.0.21. I'm using slackware current, keeping updated (almost) every day. On the Mon Feb 28 update sane was updated to sane-1.0.22-i486-1. After that update xsane (as user) cannot find my scanner. I was able to find it running sane-find-scanner as root, but scanimage -L (as root) wasn't able to find the scanner. Now I have updated to the last sane package, named sane-1.0.22-i486-2 . In the changelog I can see that this rebuild should add libusb support.
In fact, now there's no way to find the scanner. And now also sane-find-scanner (as root) is no more able to detect the scanner, also running the command as root. I've tried running sane-find-scanner -v -v and scanimage -v -v -L but I can't get no useful hints. I have checked the sane configuration files but always seems good (the row with USB IDs is not commented in the backend file, which is xerox_mfp, and the backend is listed in dll.conf).
View 10 Replies
View Related
Apr 21, 2011
I too have what looks like the same problem. I too have read all the relevant man pages and other relevant sites:
Supported devices [URL]
CanoScan LiDE 110 (the printer I've just bought) has "complete" support apparently.
Followed directions here: [URL]
Read: [URl]
Another story of purchasing a "complete"ly supported scanner. [URL]
The solution? Use windows xp in a vm.
I don't think much of that sort of solution. As a temporary work around... ok. I'm running debian lenny.
Code:
uname -r
provides:
2.6.26-2-686
Code:
lsusb
provides:
Bus 005 Device 002: ID 04a9:1909 Canon, Inc.
Code:
sane-find-scanner -v -f
provides:
libusb not available
# No USB scanners found. If you expected something different, make sure that
# you have loaded a kernel driver for your USB host controller and have setup
# the USB system correctly. See man sane-usb for details.
# SANE has been built without libusb support. This may be a reason
# for not detecting USB scanners. Read README for more details.
Code:
scanimage -L
provides:
device 'v4l:/dev/video0' is a Noname USB 2.0 Camera virtual device
Code:
dpkg-query -l '*libusb*'
clearly shows I have libusb installed:
Desired=Unknown/Install/Remove/Purge/Hold
| Status=Not/Inst/Cfg-files/Unpacked/Failed-cfg/Half-inst/trig-aWait/Trig-pend
|/ Err?=(none)/Hold/Reinst-required/X=both-problems (Status,Err: uppercase=bad)
||/ Name Version Description
ii libusb-0.1-4 2:0.1.12-13 userspace USB programming library
View 2 Replies
View Related
Apr 29, 2010
I have a debian server (squeezzy) amd 64, running with an epson BX-300f pluged to USB. And I want to share the scanner over my network. So let's do that, Intalled sane, sane utils, iscan, which I've downloaded from epson drivers and wich include epkowa drivers fro scanner to work..
after that I installed on my system (Ubuntu 9.10) xsane... on console I type:
root@bruno-laptop:/home/bruno# scanimage -L
*** glibc detected *** scanimage: free(): invalid pointer: 0x00be63d0 ***
WARNING: Unhandled message: interface=org.freedesktop.DBus.Introspectable, path=/, member=Introspect
device 'v4l:/dev/video0' is a Noname HP Webcam virtual device
device 'net:192.168.0.254:gt68xx:libusb:001:035' is a unknown manufacturer unknown device -- use override to select flatbed scanner
device 'net:192.168.0.254:epkowa:usb:001:035' is a Epson Stylus BX300F/TX300F/NX300/ME Office 600F flatbed scanner
device 'net:192.168.0.254:epkowa:usb:001:035' is a Epson Stylus BX300F/TX300F/NX300/ME Office 600F flatbed scanner
I don't know why I find so much things, if i only have one scanner. Then I opened xsane and found the scanner over network. I chose the epson with epkowa drivers I try to scan something but it dont output nothing and sometimes it gives me "end of file reached". I can put whatever config files here if you want to, just ask. One time it worked fine.. but only half of an image...
View 1 Replies
View Related
Nov 16, 2010
I have and old scanner, Canoscan 3200F, which is not supported by sane. It will not run in Wine, because there is no Sane support. Does anyone know if I was to install a Windows OS in Virtual Box would that enable me to run it or would I have the same problem as I have with Wine?
View 2 Replies
View Related
Mar 30, 2010
I have been given an Epson CX5000 3-in-1 that I only want to use the scanner part of (I have a laser and hate buying ink). The scanner works, tested under windoze, but xsane and scanimage -L fail to find it. But, lsusb does:
$ /sbin/lsusb
Bus 001 Device 003: ID 04b8:082b Seiko Epson Corp. Stylus DX5050
I saw a post about it under ubuntu that you had to modify
/etc/udev/rules.d/45-libsane.rules
Which doesn't exist on my Slackware 13 install. I hope this Epson runs faster than my Canon FB630U, which takes almost a four minutes to scan a 5x6 photo and forget scanning an 8.5x11 page (go take a nap).
View 2 Replies
View Related
Mar 21, 2011
I am having a problem with the Sane Drivers and a Scanjet HP4570 scanner. I have sane-backends-1.0.21-6.fc14 and I am running on x86_64 machine. Other info in my signature below. I have verified that the specific Scanner works as I have installed it on a Win Machine. I ran yum provides *libsane* . Results with respect to the hp5590 libs was --->
[Code]....
How to get the Scanner working, as I would expect it to work out of the box. It is one of the scanners that is completely supported, as per SANE web page info. I also have a hp3300c and it found that immediately.
View 7 Replies
View Related
Apr 20, 2010
1. Unless root chmod's /dev/parport0 to include o+rw, a user running xsane just gets the dialog 'No devices available'. Should the canon_pp driver be installed as su root, perhaps? CUPS uses the same port for printing without problems. Which library or executable needs to have permissions changed to change to run as root?
2. The N640P has a printer output port built in. As I have only one parallel port, I piggy-back my printer through the scanner. This does not work for xsane in Copy mode: nothing prints until I close xsane and then all I get printed is a stream of binary characters, not an image. I guess the canon_pp driver is holding the port open in such a way that CUPS sees the device as being busy. Any ideas on how to combat that? I am a C programmer and quite happy to help by hacking the code, if I have a start point. It irritates me to have to boot the print server into WinXP just so scanning and copying work without fuss.
View 8 Replies
View Related
Apr 9, 2010
Have Karmic 9.10 ,Changed from Epson RX595 all in 1 (uses a ton of ink)Got the Lexmark Pro 805 3 in 1 because it says it supports Linux and the ink cartridge only cost $5 downloaded drivers and printer works but using Xsane Image Scanner error reports
'Lexmark_1_0_0:libsub/001/009': Device busy Using Image Scan - reports Could not send command to scanner Check the scanner status. The RX595's scanner drivers had to been manually instatlled,, in the Printer box the Lexmark shows available..
View 3 Replies
View Related
Aug 5, 2010
I found someone who has a CanoScan 9000F (the new Canon flatbed scanner replacing the 8800F which is already supported in SANE 1.0.21), and managed to find out that it also uses the PIXMA protocol (the protocol used in the scanners for Canon's multi-function printer/copier/scanner devices of the PIXUS/PIXMA MP series (and other names depending on sales region).
Support for the scanner has therefore been added in the pixma backend. However, the initial tester is having trouble compiling and configuring SANE from source, so I am hoping there will be some people here who have access to this scanner and can try to help out as well.
After compiling SANE, if "scanimage -L" does not detect the scanner, probably "usb 0x04a9 0x1908" needs to be added to /etc/sane.d/pixma.conf and /usr/local/etc/sane.d/pixma.conf.
After that slow steps need to be taken to get support for the various resolutions, as this scanner as double the number of CCD rows as the 8800F, and can do double the resolution (up to 9600dpi) optically.
View 14 Replies
View Related
Sep 13, 2010
I have an Epson perfection V100 Photo scanner. When I open any programit will not detect the scanner. Simply plugging in the scanner and crossing fingers does not work.sane-find-scanner returns the following:
Code:
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
[code]...
View 6 Replies
View Related
Nov 16, 2010
Just upgraded from Fedora 13 to 14. My network Brother MFC-9440CN will not operate (worked fine in F13). Error message from both Simple Scan and Scanner Tool (xsane) states "No devices available".
View 14 Replies
View Related
Jun 1, 2011
I have an epson stylus sx425w which is a printer/scanner. ubuntu found and installed a driver for me and im able to use the printer fine but for some reason the scanner just isnt working. if i use the simple scan software it says connect a printer and if i press the scan button on the printer and select usb it says connection problem.
i saw a post about this already for ubuntu 10 or 9 and they provided a link for a newly released driver which turned out to be the drive ubuntu installed automatically and that hasnt fixed my problem.
anyone know what the cause could be and how to fix it?
View 1 Replies
View Related
Apr 7, 2011
I am working on an embedded system, which is an USB MSC device that supports some vendor specific scsi commands. I am using FC10 laptop as USB host for testing, and it runs some small apps based on sg3. All has been well for ~ a week. The FC10 laptop is able to communicate with the device and retrieve data. Suddenly, starting from today, the laptop is not able to properly detect the device. When plugged-in, the MSC device is detected as input device (I thought). This is observed from "dmesg" output and changes in "/dev/input/".The device under development is running at full speed. When I connect to winXP, no problem. A windows file explorer pops up, showing the content of the drive.Also, the FC10 has no problem with other USB flash drive (high speed).
View 1 Replies
View Related
Mar 11, 2011
I've got a SCSI scanner that is being detected by the kernel on Fedora 14, but XSane does not see it. If I run "sane-find-scanner" it says that noSCSI or USB scanners are found.The scanner is a Cacham Splendeur 3024, model VM3552. I believe this scanner is the same as the Relisys Scorpio VM3552. In /var/log/messages, the following entries show up as soon as the scanner is warmed up:
Code:
Mar 11 13:34:45 dt kernel: [22595.116042] usb 4-2: new full speed USB device using uhci_hcd and address 41
[code]...
View 4 Replies
View Related
Mar 7, 2010
Have an Epson Expression 1640 XL A3 scanner (usb & network interface card). Bus=0002 Device=004 its usb ID is 0x04b8 0x0109 I have never been able to connect the scanner using the network - if anybody can advise, I would be very grateful. Quite happy to use this if usb is going to be a problem The scanner has worked very well through the usb and wask working well with 9.04(32bit). I have bought a new machine and did a fresh install of 9.10 (64bit) and the scanner is not detected.
xsane detects my webcams (vl4:/dev/video*)but no scanner Have run sudo xsane-find-scanner - only the webcams are detected Have edited /etc/sane.d/epson2.conf - added scanner usb ID, and added the lines:- usb /dev/usb/scanner0 usb /dev/usbscanner0 as advised in one of the threads in this forum sudo scanimage -L gave this-
WARNING: Unhandled message: interface=org.freedesktop.DBus.Introspectable, path=/, member=Introspect
device `v4l:/dev/video1' is a Noname Creative Labs Webcam Pro Ex virtual device
device `v4l:/dev/video0' is a Noname Logitech QuickCam Pro 4000 virtual device
[code]....
Do I need to select M for these three modules?
the following had [M] -
USB Printer support
Microtek X6USB scanner support
It looks like the scanner module has not been loaded, and possibly the usbfs yet usb webcam and card readers are accessible. I have tried to keep outputs relevant & short. If I have omitted anything, you would like full results or any other information.
View 1 Replies
View Related
May 7, 2010
Using xsane with HP scanjet 3970 scanner. It used to be that when I plugged the scanner in and started the xsane a window would come up asking if I wanted to use my HP scanner or my Hauppauge video card. Well, that window no longer comes up and the Xsane wants to use my video card. When I try to "scan" the program closes and all the windows associated with it disappear.
View 1 Replies
View Related
May 22, 2011
Does anybody know where to find an rpm of sane-frontends?I want to use my auto-document-feed functionality on my scanner using scanadf, which is part of sane-frontends.Otherwise I'd also welcome alternative suggestions for scanadf.
I'm running Suse 11.2 and using a Brother DCP7065DN scanner/printer, which actually comes with stunning drivers and support for Linux.
View 2 Replies
View Related
Aug 2, 2010
I have an epson cx7800 printer/scanner that 11,3 doesn't detect on USB. I tried Yast-Hardware-printers and Yast-Hardware-printers and nothing is discovered/detected.
Are there repos for this stuff and is there a tutorial like the one for graphic card theory I could peruse?
View 3 Replies
View Related
Aug 11, 2010
I have HP Scanjet 3770. UBUNTU 10.04 installed on my desktop. HPLIP also installed. This scanjet working well in Windows Xp but in ubuntu SimpleScan does not recognize it.
It shows:- No scanners detected Please check your scanner is connected and powered on.
I Also visited [url] & found as below-
ScanJet 3770 Unsupported. While an external binary-only backend exists, it works only on Linux i386. Therefore the scanner is unsupported on other platforms.
View 2 Replies
View Related
Jul 11, 2010
I just received a Canon Pixma MX320 as a gift.
I am currently running the Ubuntu 10.04 OS
I was able to get the printer up and running by downloading the printer driver for debian linux (3.1) from the Canon site without any problems.
Unfortunately I am not having the same luck with the scanner.
I tried downloading ScanGear MP for Linux (deb) (1.3) from the same Canon site but have not yet been able to get the XSane Image Scanner to recognize this scanner driver for my Canon.
View 2 Replies
View Related
Apr 20, 2010
I just got a new scanner HP Photosmart C4640 and tried to set it up on Ubuntu 8.10SANE has it as supported, but I can't scan.Printing works fine. when I run xsane I get
Code:
Failed to open device 'v4l:/dev/video0': Invalid argument.
Poking around I found ScanningHowTo page. But I was unable to find the .fw, .usb, or a PPD
[code]....
View 3 Replies
View Related
Feb 3, 2010
I'm using debian lenny, I bought a new Hp officejet j4500 scanner but the xsane is unable to detect the scanner. It says device not found. If I run xsane as root it detects and works properly it is obvious.I have added the user to scanner,saned and also to root user group.
View 2 Replies
View Related
Jan 9, 2011
I have installed a new network multifunctional device Samsung CLX-3185FN using the drivers provided by the manufacturer (Samsung Unified Driver). The printing over the network works fine, I can administer the device using browser. The only problem I have is using scanner over the network. It works fine if I disable firewall, but is blocked with firewall enabled. I can not figure out which ports or port-range I must enable for this scanner. Do you have any information on this one or how can I found out the necessary ports to open?
View 3 Replies
View Related
Sep 1, 2009
I have recently installed Fedora11 and have managed to get the printer side of the above multifunction machine working but not the scanner . The computer recognises the scanner and sane, xsane, sanelib's etc are all installed . When I try to open it it gives the following:
Failed to open device 'brother3:bus5;dev1': Error during device I/O
View 6 Replies
View Related
Jan 8, 2010
My scanner is Benq 5000 ,the default scanning software (xsane) give me the following message whenever I plug the scanner to the pc :
Failed to Open Device 'Snapscan:libusb:005:002' Invalid Argument.
I tried the gnome image scanning software too but it didn't recognize the scanner at all. The only software that worked is vuescan but unfortunately it is non-free software !!!!
View 4 Replies
View Related
Jan 15, 2010
Ok, installing the Epson DX8400 printer driver was easy... I just turned it on, and Ubuntu searched and installed the printer itself.
But scanning... that's another story. In Ubuntu 9.04 the trick was as simple as installing libsane-extras in Synaptic, but this doesn't work in Ubuntu 9.10! When I try to run XSane, it simply replies that there is no available device...
View 5 Replies
View Related
