Ubuntu Networking :: Connect Only One PC At A Time To Adsl Router/modem For Internet Access?
Apr 1, 2011
I have 2 pcs at home. I dont have a switch so I can connect only one PC at a time to my adsl router/modem for internet access. In the past I had successfully connected the two PCs (NIC to NIC) to each other using the same ethernet cable which was supplied with my dlink adsl modem.
Recently the motherboard of on of my PC went bad so I replaced it with a new one. The problem is when I connect the two using the same Ethernet cable they won't connect. The lights on the Ethernet port won't light up. I can still connect both of them to the adsl router (NIC to Router) (one at a time).
I'm a beginner in Ubuntu, I'm using Ubuntu 9.10. Currently using a Dlink GLB-802c router and using a ADSL connection. I try to connect to the Internet but it is unsuccessful. Ubuntu is not indicating my router when I connect to the PC.
My PC is P4 and using USB to connect to internet, PC haven't a Ethernet interface.
My router/adsl modem is not connected to a power supply so when power goes and comes the network will do a re-boot. Now the problem is my OpenSUSE network won't come back on! I set the static ip as Autoeth0 to eth0 however when network updates I losse eth0. Why is this happening? Why doesn't the PC simply re-connect? Can I do it via command line?
I have an adsl modem acting as a bridge to my router my setup was working well for more than year now , but then the internet went slow . I set the modem back to PPPoE the problem was with the DNS server of the ISP so using ifup i set the dns t 8.8.8.8 (google) the connection is back , but when i set the modem back as a bridge slow internet does the router know that my dns is 8.8.8.8 or i should set the dns on the router ? I can't see an option to set the dns on the router ( i just enter my username and password from the isp to use PPPoE mode ) by the way i called the isp support they kept telling me to restart , i told them i did but i never restarted my pc . I'm sure if i tell them i'm running linux they will blame the os !
i've just installed opensuse 11.2 everything is working fine but i'm unable to connect to the internet through my adsl modem the network is shown to be active but after i configure the dsl connection i can't see any option from where to connect
I have a desktop PC running Ubuntu 9.10 and Windows 7, and a Eee PC 701 laptop running EasyPeasy Ubuntu 9.04. I'd like to connect the desktop to the laptop with a wired connection (eth0), then the laptop to my ADSL router using wireless (ath0).
I have a crossover ethernet cable (I bought on ebay). I have set up my laptop with a static IP address on my LAN and it uses OpenDNS.
I have added this to /etc/sysctl.conf on the laptop:
This is a variation on what I found on other sites describing how to set up a router. I don't understand iptables very well, but I gather that the above two lines should set up forwarding so that traffic from my router to the laptop will be forwarded to the desktop, and vice versa.
But this doesn't work. The connection doesn't even establish between the laptop and the desktop.
What are the pros and cons of various current model ADSL modem routers for use with DD-WRT, OpenWRT or Tomato? There are, of course, hardware compatibility lists (HCLs) for each of these (DD-WRT, OpenWRT and Tomato) but many of the models are no longer available and there are so many that researching them all would be onerous. Many pages on the Internet recommend the WRTG54L and that would be great but it is no longer an option except second user which is increasingly difficult. What are the pros and cons of the various chipsets: ADM5120, AR7, IXP4xx and BCM63xx?
I have a wireless Internet modem (USB) and a LAN Ethernet connection. I can only pick 1 of them to connect to (by disconnecting the other). How can I connect to both at the same time?
I have an ADSL Internet connection with static IP.I connected through PPPOE from my modem to my ISP.I need to ssh from outside of my home to my home, But i don't know to use which connection between my computer and my modem.(dhcp ,static , bridge or ....)
I just installed Lucid Lynx Ubuntu on my computer. I love it, but I do not see how to configure my dial-up modem and connect. I'm hoping it's still possible. Here's my hardware.
At work, we (like almost everyone) are still full-on windows. I am currently trying to get away from windows because I am not a fan. my current windows machine (different from my Ubuntu machine) is accessing the wireless network fine, and there are no obvious problems there. Also, my Ubuntu machine can access my wireless network at home, so I know there are no driver issues. I set up the connection for the Ubuntu machine, and it seems to be connecting OK. I can ping internal IPs and by all statuses, the connection to the router is functioning. However, when I attempt to load a web page or ping a domain or external IP, it fails. I tried to ping the IP, thinking if that worked, it's probably the DNS, but pinging both domains or IPs fails. I have looked around at forums and posts, but none of them seem to match my issue (that's probably not true, but I am struggling to see the commonality).
Here are the results of "netstat -r":
Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.45.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default 192.168.45.5 0.0.0.0 UG 0 0 0 wlan0
And here is "ifconfig":
wlan0 Link encao:Ethernet HWaddr 74:f0:6d:XX:XX:XX inet addr:192.168.45.49 Bcast:192.168.45.255 Mask:255.255.255.0 inet6 addr:fe80::76f0:6dff:XXXX:XXXX/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
My broadband internet connection came with a Nokia-Seimens C2110 Adsl modem. Please help me connect the modem through USB cable as the ethernet card is used to connect my computer(Asus- P5RD2 VM motherboard) to a different computer on LAN. I am in a fix and have no clue how to proceed.
I use an atom based processor of 1.60 ghz on intel d945gclf board. My ram is a zion 1gb @ 533mhz. Hdd is from western digital 80gb @ 7200 rpm. I have a broadband(dsl) connection from bsnl dataone (a state owned telecom service provider). I connect to internet via a huawei wa1003a ethernet/usb/wireless modem which is provided by my service provider. I need a username and a password everytime i connect to internet via dial-up.
I was using windows xp service pack ii. It was nice and easy installing my modem on xp either via usb or ethernet. Both ways it was easy as i have both the drivers with me.Only and main problem was fighting viruses. I tried many free downloadable anti-virus software to protect my maching. Initially they were fine. But after few months they stopped taking regular updates and became non-functional. I also tried symantec corporate v.10. But it has its drawbacks also. It made my machine perform like a snail.I had previously heard about linux based operating systems. But never tried one. As i am an ameteur in using computers windows xp was suiting my needs. Recently i saw an article in the newspaper about ubuntu which is a free open source operating system. And most important to me it is virus free.But here is a problem also. I cannot connect to internet. My ubuntu 9.10 karmic koala is not identifying my modem and a network between my modem and my machine cannot be established. Also i cannot create a dial-up option where i can give username and password.
I want to configure my ADSL but I don't know what should I do. Can you explain me How can I configure it?(I use fc10, ethernet cable <Asus Am608 ADSL modem)
I had an ATT "2Wire" modem/router that was working but connection to the Internet was often poor. An ATT technician came to my home and swapped out the modem/router for the identical model. I changed the ESSID and WEP code to match the new unit and everything was fine with the following wireless units: a wireless desktop, two cellphones, three wireless Archos tablets, and a couple of e-reader tablets. So all seemed to be fine wirelessly. However...
My laptop (SuSE 11.0, KDE3) simply won't connect no matter what I do. I changed the ESSID and WEP info in the lappy exactly as was done with the other wireless devices named above. But no good. The lappy does see the modem/router (a good, strong signal appears in KNetworkManager). But it seems as if the modem/router is rejecting the lappy's attempted handshake using the new ESSID and/or WEP information.
I thought that perhaps there was something wrong with the lappy's wireless card, so I took it to a Starbucks to see if it would connect there on an open network, and it did without problem. So the lappy's wireless card appears to be working fine. It just won't talk to the encrypted modem/router at home. Here are the settings on the lappy. Hopefully something here is easily identified as the culprit. With all the clicking I've done it certainly is possible that I ticked something that should not have been ticked and just don't realize what I've done.
Network settings screen: Global options tab: Network setup method: user controlled with Network Manager Change default route via DHCP (ticked)
[code]....
Why won't the new modem/router which is exactly the same as the old one except for the ESSID and WEP work with my lappy yet it does work with a bunch of other wireless devices?
I have an ADSL line that allows me for maximum of 4 concurrent users with external IP addreses. The IP addresses are not static (they change every 3-4days).
My current setup is as follows: * A-link Roudrunner 44B Modem connected to the main line * D-Link DI524 Router (port 1) connected to the modem * This leaves me with 3 ports and Wireless for my other machines
What I wish to do is: * Have all my machines with static IP addresses for LAN * still have internet connection
I've tried enabling DHCP on the D-Dlink Router with LAN IP 192.168.0.1 and IP range from 192.168.0.100 - 192.168.0.199. Then gave my machine static IP 192.168.0.101, subnet 255.255.255.0 and gateway 192.168.0.1....obviously it didn't work. I've tried the above with both the modem being connected to the router via port1 and WAN port... but I have the same results. I also tried to do the same without the router (direct connection between the PC and modem) still got the same results. Could it be that what I am trying to do is not technically not possible due to my ISP setup to ensure no more than4 concurrent users limit is in place.
I have an valid account,and I used pppoe-setup to set the dial correctly.After the configuration,I typed "ifup ppp0",nothing wrong happens(no news is good news?).Then I typed "pppoe-status",it said I've connected to the internet . I opened firefox,updated my system through yum ,they all said I haven't connected to the network!!!I've formated my harddisk and reinstall my system,but the problem is still.
i'm running Kubuntu karmic and i've been using a 3G Huawei E1552 modem to connect to the internet, everything was going well when suddenly my modem stopped working. I've tried reconfiguring everything, i even reinstalled kubuntu from scratch with no success.Here's a part of my /var/log/debug
HTML Code: Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099883] usb-storage: device found at 7 Feb 8 17:14:01 alberto-laptop kernel: [ 1532.099888] usb-storage: waiting for device to
After reinstall Ubuntu 10.04 LTS didn't recognize my ADSL router Billion 400 G.The Ethernet 1 led is off after booting.Search on web for help on this but no good results.You good people now are my last resort.I tried boot in live CD and result is the some.Check with sudo lshw.
Because of the configuration of my house, I need two routers.I have a DLink ADSL router as my main router and the Belkin N1 as my repeater.I have set up the IP address in the Belkin to be 10.1.1.10 - my DLink is 10.1.1.1. I have disable the dhcp in the Belkin and set the DNS as ISP provided. [URL]..I have set the channel to 11 and in the Ubuntu Network Manger I have set the IPV4 to Link Local Only. I can see the Belkin and connect with my PC.but it will not take me through to the internet.
I just bought a TRENDNET TDM C4000 (=modem/ wiredrouter) and got it working. If I connect my computer with through the ethernet port directly, the internet will work. However, when I try connecting the ends of the ethernet cable on the modem and my wireless router, it's not transmitting. I know I set up the wireless router correctly because it worked with my previous modem. I just need to know how to configure my modem so that it works with my wireless router (D-Link DI-524).
I have a long wired ethernet wire to satisfy my academic needs for the internet at the moment but my mother is not able to surf the internet and it would be more convenient for myself to put the wire back to my desktop and have my laptop browsing wirelessly.
I have 2 machines both using U 11.04, one of them being Studio. I have tried to connect them together (via a modem/router of course) to browse files but I can't connect. I get error messages. I've installed samba and everything.
I use Opensuse 11.2 & Edge/Gprs Modem to connect Internet.I configured /etc/wvdial.conf & /etc/resolv.conf. Now I can connect Internet using this command "wvdial MYNET" in terminal.Now I want to share my internet using Lan card & Netgear Router. If i connect my PC with Router using wire & change option ON BOOT find this device in ifup then it'll show in ifconfig command.
My Router IP : 192.168.0.1 & It gives my PC an IP automatically : 192.168.0.2
I can ping my router.. even I can browse Router Admin page in browser. No problem there.But now If i want to connect my net using wvdial command... net connected... but no data passing!!! If i disable Lan card in ifup then Edge/Gprs net connection again OK!
i'm having problems connecting to the internet unless i manually enter the IP info.
automatic DHCP does not work. I'm on a dual boot machine vista/ubuntu 10.04 LTS connecting to the internet through a lynksys wireless g router and a cable modem.
Due to PCI limitations on our server, we are trying to connect a Trandnet TDM=C400 ADSL modem via USB but are not having any luck, as the modem appears not to be recognised.
I am trying to setup a dhcp server for my internal network. I have two NICs, a modem, and a wireless router. I have my server connected directly to my modem which is providing me with Internet access on eth1 and is working fine. I have dhcp and dns setup on eth0 which is connected to my router. The router shows that it is connected to the Internet but when the router gives a client computer an IP address, the client is unable to connect to the Internet but can connect to the router. I will post my configuration files below with my current configuration.
