I'm running 10.10. I have a Nvidia GTX 460. My actual resolution is only 1024x768. I can't get the native resolution (1280x1024). Nvidia-settings does not show this resolution. Google hasn't helped at all so far, and I have installed the Nvidia Driver.
View 2 Replies
When I boot my computer I get this message: Warning Pc video resolution is out of range Change setting to recommended resolution 1280x1024 @60mh So I hit ctrl alt f1 I typed in Sudo dpkg-reconfigure xserver-xorg Nothing happens. It's been very frustrating because with everything that I've looked up it says that it's suppose to guide me through something. I desperately need my computer for school.
View 8 Replies View RelatedBarebones installation. Manually start x with 'startx'. For some weird reason, the resolution randomly sets to either 1024x768 or 800x600. How do I permanently set a resolution?
View 1 Replies View RelatedYesterday I installed ubuntu 10.04 LTS, it allow me only 800x600, 640x480 and 400x300 screen resolution, how can i set 1280x1024 ?
View 9 Replies View RelatedI just want my normal settings back. I deleted the original post because I really screwed something up and I have to use Windows until I can figure out how to fix it. Forget about my resolution preferences. My Linux boot is stuck in low-graphics mode
Would anyone be able to provide me step by step, easy to follow for a newb instructions on fixing my boot?
I have to use recovery mode to load any graphics at all, and it's stuck in low graphics mode and I can't change it. More info below.
I'm new to Ubuntu, just installed it today as my Windows 7 got corrupted and couldn't boot. So far it's great, but I have on issue. My monitor is unrecognized, and I can't go to 1280x1024 resolution at all. I only have these options:
640x480 4:3
848x480 16:9
800x600 4:3
1024x768 4:3
1360x768 16:9
I have an HP Compaq dx2200 I have a Viewsonic VA 702b Monitor Did all possible update, no help. Even tried to use the "additional drivers" option and none were shown.
I need to set my resolution to 1280x1024. Problem is, that the NVIDIA X Server Settings does not display such a resolution and I want to use that! My monitor is an LCD capable of upto 1280x1024 75HZ resolution. I'm using Ubuntu 10.10. I did the xrandr command to check what resolutions are available and its output was:
Failed to get size of gamma for output default
Screen 0: minimum 320 x 240, current 1024 x 768, maximum 1024 x 768
default connected 1024x768+0+0 0mm x 0mm
1024x768 50.0 60.0*
800x600 51.0 52.0 53.0
680x384 54.0 55.0
640x480 56.0
512x384 57.0
400x300 58.0
320x240 59.0
In NVIDIA X Server Settings, the list of available resolutions are:
(all of the above)
1152x864
1360x768
I have NVIDIA GeForce 9500GT.
I am getting a screen resolution of 1280x1024 on my laptop, but I sometimes like the lower resolutions, which are unaccessible via the Screen Resolution program.
View 2 Replies View RelatedI'm a first timer on Ubuntu and I have a little problem with my Nvidia graphic card. After lots of attempts I can't get the 1280x1024 resolution that both of my monitors have. Instead I'm running on 1024x768.Is this a way to fix it?
View 8 Replies View RelatedI have Ubuntu 10.04 32bit installed on my desktop. My video card is an nVidia 7800 GT. My Monitor is a Sceptre X24WG. I am able to use the NVIDIA X Server Settings utility to change my resolution to 1920x1080 as well as 1920x1200,and 3d opengl accelerated games work. When i reboot, the x server comes up with 1280x1024 as the resolution. I want it to remember the resolution i selected instead of defaulting to a different resolution.
I was running Kubuntu 8.10 previously and had some difficulty setting up the graphics initially, but i don't recall what steps i had taken to get it to work. When i recently reformatted to install Ubuntu 10.04, it wouldn't go directly to 10.04. The screen would go to a garbled display and would load the install window, so i installed 9.04 and then upgraded to 9.10 and then 10.04, without trouble.
I'm using the nVidia hardware driver version 195.36.15, which in the hardware drivers utility is listed as the current and recommended version. It originally wouldn't install until after i had rebooted into the 2.6.31-21 kernel. I have tried the option to save to x configuration file. When i save to x configuration file, the xorg.conf in /etc/X11/ looks like this:
Code:
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildd@palmer) Fri Apr 9 10:35:18 UTC 2010
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder75) Fri Mar 12 01:42:27 PST 2010
# xorg.conf (X.Org X Window System server configuration file)
[Code]...
Well i have HP D2832. A very old CRT Monitor from HP which have resolutions supported upto 1300 one but i can't get the resolutions after 1024x768. I want to get 1152x864 and cannot work to get it show in Monitors Panel.
In monitors panel it shows: Monitor: Unknown.
change my resolution from 800x600 to 1024x768..since the latter option is not available in my display settings?
View 1 Replies View RelatedI'm trying to use the Xubuntu-based BitDefender Rescue Disk, and having an issue. Posting in their forum didn't return anything, so I figured I should ask here next.
Using the default settings, the Rescue Disk starts in 800x600 and complains that the resolution is too low to run the app in graphic mode.
FYI, this servers + monitor run Windows just fine in 1024x768 @ 75Hz, and even higher.
I tried adding "screen=1024x768" to the command-line, to no avail.
FWIW, the default includes "vga=791" but I don't know what it means.
If someone had the same issue, how can I set the resolution to something higher so I can run BitDefender in graphic mode?
I can't change the video resolution for Intel 82740 (i740) video card.I'm new to Ubuntu 10.04, as I've just installed it and I have a problem with video settings.I can't change video resolution for my video adapter. I can only choose between 800x600, 640x480,400x300... not 1024x768 for example.No restricted or proprietary drivers...I used Knoppix 5.1.1 Live CD and it automatically set the resolution to 1024x768.I also used Puppy linux 5.1 Live CD and it had a configuration program which also utilised 1024x768.If these versions of linux can utilise the 1024x768 resolution, why can't Ubuntu 10.04
View 9 Replies View Relatedafter the latest kernel update (2.6.32-26), my computer will no longer start up with a screen resolution higher than 800x600. Before this update, my computer would sometimes startup with this problem, but this could usually be fixed with a restart (or two if necessary). At this resolution the panels and a lot of tool-bars will not display properly, so I am limited as to what I can do using the GUI. my video card is an S3 unichrome (I think. It is built-in to the motherboard so I don't know for certain) my screen is an old ctr one I am running Ubuntu 10.04 on the 2.6.32-26 kernel.
View 3 Replies View RelatedI cannot get 1024x768 resolution permanently in my screen. When i go and adjust it in the kde personalize setting in the display menu everything seems to work. But after i reboot the system, the resolution again changes. Then i have to again configure it to 1024x768. Also i cannot find sax in openSUSE 11.3.
View 7 Replies View RelatedFC12-x86_64/KDE I want to set my resolution to 1024x768 using Intel Video adapter using the the i915 kernel module.
Putting the line below in /boot/grub/menu.lst on the kernel line after
rhgb quiet i915.modeset=1 vga=318
Is this the correct setting ?
I don't want to use a xorg.conf file.
Can't make Slack 13.1 to run at more than 1024x768. No problems where with 12.0-13.0. Here are portions of my xorg.conf and Xorg.0.log:
Code:
Section "Monitor"
HorizSync 31 - 81
VertRefresh 56 - 75
Section "Device"
[code]....
Note the last line marked (**) - "from config file", but I only have 1280x1024 there ! And what does that mean
(II) NV(0): Using fuzzy aspect match for initial modes
(II) NV(0): Output VGA2 using initial mode 1024x768
(--) NV(0): Virtual size is 1024x1024 (pitch 1024)
And KDE/Display only offers up to 1024x768 too. Didn't try NVIDIA driver yet but 13.0 had no problems with the same monitor,similar Card and nv driver.
I installed 10.04 on my former windows box last night, and I seem to be stuck at a screen resolution of 1024x768. I have a Geforce 7600 GT graphics card, and I installed current drivers via the hardware drivers option. I can't go above this resolution in the nvidia x-server settings, and even xrandr says the highest resolution I can use is 1024x768. What is up with that, and how can I change it?
View 1 Replies View RelatedI have recently installed Ubuntu on my Toshiba Satellite A25-S207 Laptop. Everything runs great except that the resolution will not go above 800x600. I had this problem before on the same laptop and was able to fix it but cannot find the fix now (I had to wipe my laptop clean in order to remove some pesky Windows partitions and reinstall Ubuntu) I have found several "fixes" but none work. I tried the one below as well as it applies almost perfectly to my problem
"I just installed the latest ubuntu 10.04 on a Toshiba-Tecra having "Trident Microsystems Cyberblade XP4m32" Monitor. After install resolution is defaulted to 800x600. I followed a method advised in some threads (arount xrandr and cvt) to increase the size (my laptop works with 1024x768 under XP). This was done OK and I obtained the resolution 1024X768 appearing in the drop list resolution options of the Monitor preferences but when I select the option if fails. Alternatively, when I execute $ xrandr --output default --mode 1024x768_60.00 i got the message "xrandr : screen cannot be larger than 800x600 (desired size 1024X76
I also saw a possible fix proposing to add "HorizSync 31.50-48.00" in Xorg.conf but I then I DO NOT have such a file in my /etc/x11/ after ubuntu install (supposing that this will fix my problem !!!)
Boot into recovery mode, when you get to the command line type:
sudo Xorg -configurewhich will create a default /etc/X11/xorg.conf file. Add the lines:
HorizSync 31.0 - 70.0
VertRefresh 40.0 - 75.0to the Monitor section then reboot."
However when I entered the "sudo Xorg -configure" line my computer spit back saying that "sudo" is not an acceptable command
I have a Dell U2311H monitor which has a native resolution of 1920 x 1080. My graphics card is an ATI 6870.
Last night I installed Ubuntu 10.10 alongside my Windows installation, and when booting into Ubuntu, the maximum resolution I can select is 1280 x 1024.
How can I resolve this to get Ubuntu to display at the native resolution?
I installed Debian 8 Jessie with the GNOME 3 desktop environment and I couldn't get pass the login screen after several reboots. Since I read that NVIDIA graphics are problematic, I decided to reinstall the system but selected Mate desktop, which appears to be less graphic intensive than GNOME 3. It worked. However, I can't get a higher resolution than 1024x768 (In Windows I could). The Mate settings in the "System → Preferences → Monitors" does not show higher resolutions.
The information of the graphics card is this:
Code: Select all00:0d.0 VGA compatible controller [0300]: NVIDIA Corporation C61 [GeForce 6150SE nForce 430] [10de:03d0] (rev a2)
Before I try to install proprietary drivers as instructed in [URL] ...., I'd like to see if there's anything to try first with the default stuff installed by the system, because that page says:
As of jessie, the need for the proprietary drivers is pretty much over - nouveau now works quite well and works with dual-headed displays by simple and easy configuring from within your desktop(for KDE see System_Settings/Hardware/Display_and_Monitor/Display_Configuration) . The proprietary drivers don't provide normal logging and can be a hidden source of problems.
I've googled the issue and had a little luck, though I can't seem to change my xorg.conf file because permissions are defailed. This is the example xorg.conf file I wrote based upon my original and the modifications:
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
[Code].....
I am using Mercury p4VM800 mother Board and Intel PIV 2 GHz Processor. I have installed the fedora 10 Today. My screen resolution was automatically set to 650x480 and this is the only option available in graphical mode. I am not able to increase the resolution to 1024x768. I once again reinstalled the F10. during the installation, in the boot: option I have entered 'linux resolution=1024x768', but it won't work.
View 4 Replies View RelatedI'm still on GNOME with 800x600 resolution but I can't switch to 1024x768 because there is no 1024x768 option under resolution settings.My monitor is 17" so 1024x768 should work fine.My graphic card is integrated GeForce 6150.
View 6 Replies View RelatedI have ati radeon 9600x series card. Cannot change resolution higher than 1024x768.
View 3 Replies View RelatedMy graphics card just died so I bought a Radeon HD 4350. My monitor is an Acer AL1916W whose default resolution is 1440x900. So I reinstalled Fedora 14 with KDE but I can't set the resolution higher than 1024x768 because that is the highest available.
Code:
[corneliu@localhost ~]$ lspci
00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 200 Host Bridge (rev 01)
00:02.0 PCI bridge: ATI Technologies Inc RS480 PCI-X Root Port
00:11.0 IDE interface: ATI Technologies Inc IXP SB400 Serial ATA Controller (rev 80)
[Code].....
I rebooted but still no dice. I saw a video on ..... using a graphical tool to modify the monitor settings but it seemed to be a Gtk application and I rather not use Gnome applications in KDE (not that I don't like Gnome, but I don't like to mix applications).
Can't set screen resolution 1024x768 permanently. There is no tools like sax2 which is in openSUSE 11.2. I am to set screen resolution to 1024x768 every time after loggin in.
View 3 Replies View RelatedI just installed 11.4 x64.I have already updated and installed the nvidia 260.19.36 driver via the nvidia repository. The video card is a GEforce 6200.The problem is the highest resolution it will allow is 1024x768.With the same hardware in 11.3 it was running 1920x1200. How can I get that back?
View 9 Replies View RelatedIt's an HP DX2300 running Fedora 13, I think it has NVidea chipset, my other computer is similar machine running Redhat 5.5 and it does 1680x1050 with the same monitor.
View 15 Replies View Related
