We have several new DELL STUDIO-XPS machines pre-packaged with Win7 onto which we intend to load 10.3 the 2.6.22.5-31-default kernel as a dual boot.
The first test machine however is showing reluctance to reveal its NIC under SuSE. The card in question is a Broadcom Netlink (TM) Gigabit Ethernet with driver version 12.4.0.3 under Windows.
The error message I recieve under SuSE is "Unable to configure network card because kernel device is not present".
ifconfig confirms this showing only the loopback device.
The tg3.ko driver seems to be OK (although I am not sure how to interogate this file for its vesion?). It is listed under /sbin/lsmod and I have attempted a rmmod followed by an insmod but thsi seems to have no effect.
Talk on the net suggests Windows will not 'let go' of the card on a dual boot machine but this seems unlikely and I have attempted the various power down options without success.
I have installed Linux SuSE 10.3 on a PC (Lenovo Thinkstation A58). However, when I start the computer I get the following error message:
"No valid Host_ID or host-name found."
I then use YaST to set up the network. I get the following error message:
"Unable to configure the network card because the kernel device is not present."
The computer has Windows 7 installed and everything seems to work fine. The LED on the Ethernetplug is blinking when using Windows, but not when using Linux. I guess this means that there is no driver for the Ethernet card (Marvell Yukon 88E8057). I have not found any driver for the card and am considering buying a new one. Which PCI card works with SuSE Linux 10.3?
Installed a TP-Link TG-3269 Gigabit card in a machine running OS 11.3 32 bit, when I go into Yast, Network Devices, Network to try configuring the card I get this errormsg: Unable to configure the network card because the kernel device (eth0, wlan0) is not present. This is mostly caused by missing firmware (for wlan devices). See dmesg output for details. Couldn't find any mention of the card in dmesg's output, (though the 8139 onboard card is in there) there is some stuff about pci host bridge but I don't know whether they would be relevant or not
The chip on the card says it's rtl8169sc but lspci lists it as being 00:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 8369 (rev 10) Done some googling and there don't seem be any drivers for a Realtek 8639 and it returns no matches from a search on realtek's site, but there is a driver there for rtl8169sc chips, which I downloaded and installed, no errors when installing it Even after a reboot I still get the same error in Yast's Network Settings screen, lspci still lists it as 8369 and the device isn't listed at all if I run ifconfig
i am using intel hardware on this working on suse linux 10.2 . i am not able to configure the network card IP address I have tryed using dhcp and static both way. Currently intel DG41RQ network card is assembled in my system. by using command ifconfig i can see only lo but eth0 is not displayed their.
I've installed the Ubuntu 10.04 Server onto a PPC G4 Mac just for the experience of setting up a server. During the installation process Ubuntu couldn't auto-configure my DHCP Network. I'm using the airport card on a wireless network. How can I manually configure the network once Ubuntu is installed.
I've searched a lot across the web and this forum in particular, but wasn't able to find the solution. The settings of the firewall are too cryptic to me. When the firewall is turned off everything is OK, but it is uncomfortable to turn it on and off every time I watch IPTV.
I just switched from Ubuntu to Fedora 13 because I was unable to get Ubuntu to connect to wireless networks. I tried everything suggested in help and forums, and kept getting "Bad Password" with WICD and Network Manager. Now, with Fedora...I still can't connect.
Problem #1: The guide says to "...make sure that the relevant wireless interface (usually eth0 or eth1) is controlled by NetworkManager," and that I do this via: System>Administration>Network
However, there is no Network option under System>Administration.
Problem #2: I open Network Manager, which displays a list of networks. I click on mine, configure it with WPA and the right password, and it fails to connect: "The network connection has been disconnected."
Complete n00b here. I am running openSUSE 11.3 and trying to load drivers for a network card. When I try to make install, I am getting this error:
Code: Makefile:69: *** Linux kernel source not found in any of these locations: Makefile:70: Makefile:71: *** Install the appropriate kernel development package, e.g. Makefile:72: *** kernel-devel, for building kernel modules and try again. How do I install the kernel-devel?
I'm going to come right out and say I am a complete novice with Linux/SUSE. The equipment I'm having a problem with is a little web-server that was purchased by my employer that has, quite suddenly, stopped functioning. I was changing the IP address within YaST, at which point the device offered to update itself, which I saw no harm in. Post-update, however, I was unable to so much as ping the device.
I tried "ifconfig eth0": "Error fetching interface information: Device not found." I went into network settings via YaST and found that there are two cards now listed as: RTL8111/8168B PCI Express Gigabit Ethernet controller Both IP addresses are "Not configured". The information pane, for both cards, cites:
RTL8111/8168B PCI Express Gigabit Ethernet controllerBusID : 0000:02:00.0 Unable to configure the network card because the kernel device (eth0, wlan0) is not present. This is mostly caused by missing firmware (for wlan devices). See dmesg output for details. The only difference in either of the cards is the BusID (0000:02:00.0 and 0000:03.00.0)
I can neither edit nor delete either of these cards. As I mentioned, I am a total Linux novice, and am at a total loss for what to do next, or even how to find critical information about the system itself. I know enough to check dmesg, but not enough to have any clue what to look for in the output.
I am using FC6 on my system, I tried to configure the soundcard using, system-config-soundcard utility. But once I type system-config-soundcard from my shell, it doesn't start at all. However its not showing any error also. What can I do next?
I am using Redhat enterprize linux and using ethernet card Realtek PCIe FE Family Controller. I tried to configure my network card. But unable to activate it as message appears "No such device found" I am using Dell inspiron laptop.
Wireless card detected but cannot connect to a wireless network
I have install it suse 11, and everything went well until the wireless thing is not working, my card is Broadcom BCM4318, I see my card on the network settings but I cannot configure the card, and also I cannot connect to a wireless network, can someone tell me what to do here, I am loosing my patient....
I'm trying to configure my network card using the b43 driver. I'm running 10.04.2 on the kernel version 2.6.35-25-generic-pae.
Surprisingly, I was able to connect to my home wireless network using the b43 driver without a problem. The only issue is that it doesn't automatically connect. I have to use the following command in order to get it to work:
Code:
After typing my password, I wait for 10 seconds and am automatically connected. My question is, how do I configure my system to do this for me permanently (or at least automatically) so I don't have to type it every time I log on?
Intel 1000GT gigabit Network Card itself installed successfully and shows up under network cards. However, when I plug it into the network in place of the regular 100mbit card, it won't show up.
I installed 10.3 (after buying it a couple of years ago and letting sit on the shelf) and can't get it to configure my ethernet connection or my wireless card. Yast doesn't include a list of available cards, and the error I get in installation-network setup is that the kernel isn't present. The machine I'm installing this on is a Lenovo, in which there isn't a discrete ethernet card (it's in the motherboard), but my wireless card (a Cisco LINKSYS 802.11G) is a discrete card. Because I'm divorcing Microsoft for a number of valid reasons, I don't have Windows available on that box.
I have a windows machine (in a domain) and I have created 2 Virtual Machines with Suse 11.2 installed on them.Now, I want to share a folder in windows to both Suse images. I am succesfully able to do that.I used: mount -t cifs -o user..... command to mount it at /mnt/win on my linux and succesfully able to work with it.
Now, I want a user in my Linux box (both Linux images)to be able to write to the shared folder in windows (actually both linux images will write to the shared folder but it is based on acquairing locks and releasing them to be able to use the shared folder on windows).
I tried etc fstab and lot other options but my efforts were in vain.Simply put - I need a user in my linux box (suse 11.2) to be able to write to a windows shared folder.
last night i have install SUSE 11.2 from the live CD. I have dual boot system with windows.Here is the problems.....i m able to access internet using same connection in windows but unable in suse.
Just installed Suse 11.4 Kde build. Using 64 bit ECS A780GM-A Ultra Mobo, 4 gigs ram, Athlon 7550 CPU, I am unable to detect my Verizon broadband MIFI 2200 with this new OS, have used Ubuntu in the past. Plugged in USB cable for modem into different ports, still does not work,
I HAVE DUAL BOOTING SYSTEMVISTA + RED HAT 5.0ON VISTA I CAN RUN WI FIBUT ON RED HAT IT CANT WORK AND SAYS CANNOT ACTIVATE NETWORK DEVICE eth13c501 device eth1 does not seem to be present delaying initialisation.
I am a first time Linux user - though I've Unix and Windows experience. So though I can follow your most tech instructions, I'll need some hand-holding.
Need help getting my wireless network to work on my newly installed Oracle Linux on Dell laptop.
Not sure what wireless card is installed, or it's mac address (though I can boot into windows and get that info, I don't want to - it'll be kind of a let down if I can't fix it all thru Linux).
Install has detected a Broadcom wired card, but not the wireless. Funny thing is that it detected the Bluetooth.
The graphical option through the hardware drivers list 2 options, broadcom b43 wireless driver and the broadcom sta wireless driver None can be activated
The b43 displays: Sorry, installation of this driver failed.
Please have a look at the log file for details: /var/log/jockey.log
When i am adding a user using "useradd -d /home/test test" or "useradd test", it is now creating the home directory, whereas when i am using the graphical mode and going through several menu options, i am getting the home directory.
I'm using ubuntu karmic and I'm not able to connect to the internet with my reliance netconnect data card using network manager. Other distros like fedora, opensuse n sabayon connected easily with nm. Ubuntu detects the data card flawlessly but just doesnt connect.This problem has been persistent even in previous ubuntu versions, n I used to use wvdial. But downloading wvdial on some other comp with every dependency is really cumbersome.
abhishek:/ # sudo /usr/sbin/iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a Flags: bus master, fast devsel, latency 0, IRQ 23 Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
I'm trying to get dual monitor support enabled in Suse 11.3 Previously I had this in Suse 11.2 using a dedicated NVIDIA graphics card with VGA and DVI output and this was done in a GUI. I now have 11.3 and a built in ATI card with VGA and DVI output When I run xrandr I get the following Code: Screen 0: minimum 320 x 200, current 1440 x 900, maximum 8192 x 8192 VGA-0 connected 1440x900+0+0 (normal left inverted right x axis y axis) 408mm x 255mm
I tried using xrandr --screen 1 but it says Code: Invalid screen number 1 (display has 1) I'm looking to expand the desktop onto the second screen so I can photo edit on one screen and web browse and instant message in the other screen Currently using the Radeon R600 classic driver from ATI
