Intel 1000GT gigabit Network Card itself installed successfully and shows up under network cards. However, when I plug it into the network in place of the regular 100mbit card, it won't show up.
View 8 RepliesI have installed SLES 10 SP2 but my network card is undetected. Model: Intel(R) 82567V-2 Gigabit Network I have the drivers for linux on my installation cd as:
- e1000-8.0.2.1.tar.gz
- e1000e-0.3.3.3.tar.gz
- igb-1.2.24.tar.gz
How do i install these drivers on linux?
How do I know if my intel chipset graphics card thing is installed?.
View 1 Replies View Relatedi am using intel hardware on this working on suse linux 10.2 . i am not able to configure the network card IP address I have tryed using dhcp and static both way. Currently intel DG41RQ network card is assembled in my system. by using command ifconfig i can see only lo but eth0 is not displayed their.
View 4 Replies View RelatedI am running Lucid Lynx and have only noticed this problem in the past couple weeks. Before Lucid I ran Jaunty & Karmic on this same box, although I installed Lucid as a clean install. My problem is that up to 5 or 6 times per minute my networking card drops its connection and then has its connection re-established. I have an integrated Intel 82566DC gigabit card on an Intel Motherboard DG35EC connected to a 10/100 network and am running the 64-bit version of Lucid. I've done some considerable searching on this problem and although I've seen many references to similar problems dating back several years, I have found none that seem to have any solutions that do anything for me. I never had this problem under any prior version of Linux on this box (all prior versions were also 64-bit).
In short, this block of messages repeats in my messages log:
May 18 20:18:50 mark-desktop kernel: [10121.062129] e1000e: eth0 NIC Link is Down May 18 20:18:52 mark-desktop kernel: [10122.730873] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX May 18 20:18:52 mark-desktop kernel: [10122.730876] 0000:00:19.0: eth0: 10/100 speed: disabling TSO
Most of the time I don't even see that the connection has gone down. Sonetimes everything seems to be operating fine for a half-hour or more, although it could be dropping out and coming back really quickly all of the time. Sometimes it goes out for 10 seconds.Sometimes it goes out for many minutes and I can get networking back by killing disabling networking and then re-enabling it. It's quite annoying.
I'm sorry if I'm duplicating an existing issue on this forum, but I can't find this exact problem anywhere. Does anyone have any clever ideas about how to fix this?
My problem is similar to this one [URL] and I've already tried some of the steps, to no final resolution.The OS in question: Ubuntu 11.04 64 bitProblem hardware: Intel Ethernet 82567V-2 network card[URL]I've already installed the latest driver using the README instructions (sudo make install, etc).The network card will connect ONLY to my Linksys router but not even to my Motorola cable modem, even when it's directly connected to the modem ! I cannot get any web pages at all outside of my LAN, only my Linksys configuration page on my router.As I said above, I've already tried most of the steps in that forum post above. I'm going back to retrace my steps to see what else I can do
View 1 Replies View RelatedI have recently installed Fedora F11 with a Samba server. The smb.conf seems fine but I cannot see any of the files in the share from a Windows machine. I am probably missing something unbelievably simple but driving me nuts!
I can see the machine and share from windows
When logged in as the user fred I can see all the files in Linux - most are owed by fred.
smbuser:
Code:
# x_name = SMB_name1 SMB_name2 ...
root = administrator admin
nobody = guest pcguest smbguest
fred = fred
smb.conf:
Code:
[global]
workgroup = Workgroup
server string = Samba Server Version %v
netbios name = MachineName
hosts allow = 127. 192.168.0.
.........
[Docs]
comment = Main Documents
path = /mnt/documents
read only = no
browseable = yes
valid users = fred
.........
The other thing I find a bit odd is that
Code:
service smb restart
does not effect the way that the windows machine sees Samba. It appears that you need a full restart to get the changes to show properly.
Thanks,
Michael
Wireless network card is showing as "disabled"...How can I enable it through Ubuntu?
product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller
*-network DISABLED
I am attempting a simple two computer office network using Samba. When attempting to access the shared director, a screen pops in Linux and Windows requesting a user name and password. I haven't established a user name or password. Is there a way to allow any computer on the network to access the shared file without a user name and password?The following is the result of:
cat /etc/samba/smb.conf
[global]
add machine script = /usr/sbin/useradd -c Machine -d /var/lib/nobody -s /bin/false %m$
domain logons = No
[code]....
NIC: Intel 82574L Gigabit mobo network card
Issue: After the server has been up for a random amount of time, the network connection is lost. Attaching a console and looking at ifconfig I see a large number of dropped packets and collisions.
use;
Code:
lspci -vxx
to list the make manufacture of NIC and the device driver it is using.
In this case: Intel 82574L, e1000e
Look in var/log/messages to get the version of the driver, in this case 1.0.2
Download .gz file with source code, follow instructions to install newest driver (e1000e.ko), in my case version 1.2.10. [URL]
I'm building a new router for my home. I have a pci-x motherboard with two network connections on the motherboard, SUSE 11. I intended to use one network connection for the external zone and the other for the Internal zone, (the internal port going to a four port switch). Recently, a friend gave me an "Intel PRO 1000 MT PCI-X Quad-Port Adapter C32199" which will plug into my motherboard, presumably giving me a total of 6 (4+2) network connections. 1) Can it be as simple as setting one network connection to "external zone" and the other five to "Internal zone", and plug my other computers into the internal zone connectors, eliminating the need for a switch?
2) There seem to be a lot of these QUAD server adapters on Ebay; how where they originally used?
3) Can I dedicate one internal net-port for some exclusive traffic (e.g. all mail, going to network connector 3, connected to the mail server)? IPtable rules?
I bought a Mini ITX motherboard Intel DH57JG bu the installation DEBIAN does not recognize the ethernet card.
View 9 Replies View RelatedWe have several new DELL STUDIO-XPS machines pre-packaged with Win7 onto which we intend to load 10.3 the 2.6.22.5-31-default kernel as a dual boot.
The first test machine however is showing reluctance to reveal its NIC under SuSE. The card in question is a Broadcom Netlink (TM) Gigabit Ethernet with driver version 12.4.0.3 under Windows.
The error message I recieve under SuSE is "Unable to configure network card because kernel device is not present".
ifconfig confirms this showing only the loopback device.
The tg3.ko driver seems to be OK (although I am not sure how to interogate this file for its vesion?). It is listed under /sbin/lsmod and I have attempted a rmmod followed by an insmod but thsi seems to have no effect.
Talk on the net suggests Windows will not 'let go' of the card on a dual boot machine but this seems unlikely and I have attempted the various power down options without success.
I've installed Suse linux 11.3 (kernel 2.6.34.7-0.5) on my brand new computer HP all in one 5130. Everything worked incredibly well : Wifi, wireless keyboard and mouse, sound, webcam.. There is only one remaining issue : I get a very poor resolution (1280x1024) instead of the 1920x1080 allowed by the screen. The graphic card is an intel chipset (HD graphics) integrated to an intel core i3 CPU. Here is (part of) the X11.org log :
Code:
X.org X Server 1.8.0
Release Date: 2010-04-02
[ 15.124] X Protocol Version 11, Revision 0
[ 15.124] Build Operating System: openSUSE SUSE LINUX
[ 15.124] Current Operating System: Linux linux-7xhd 2.6.34.7-0.5-desktop #1 SMP PREEMPT 2010-10-25 08:40:12 +0200 x86_64
[Code]....
Complete n00b here. I am running openSUSE 11.3 and trying to load drivers for a network card. When I try to make install, I am getting this error:
Code:
Makefile:69: *** Linux kernel source not found in any of these locations:
Makefile:70:
Makefile:71: *** Install the appropriate kernel development package, e.g.
Makefile:72: *** kernel-devel, for building kernel modules and try again.
How do I install the kernel-devel?
Wireless card detected but cannot connect to a wireless network
I have install it suse 11, and everything went well until the wireless thing is not working, my card is Broadcom BCM4318, I see my card on the network settings but I cannot configure the card, and also I cannot connect to a wireless network, can someone tell me what to do here, I am loosing my patient....
I have a fileserver that I want to share out samba shares. However, i configured samba to have another netbios (SAN) and my windows box still sees whoopn-SAN which is the name I gave to my server when i installed it. Now I am using 9.10 and I know that i can create a share from the gnome gui in nautilus and that appears to be a windows like share. How can I turn OFF the windows like shares that ubuntu does out of the box and use ONLY samba? I ask because there appears to be a conflict of permissions b/w samba and this stuff.
View 7 Replies View RelatedI learn from many experts online, and finally it works but still happens some sharing problems that I can handle it in different way. Here is what I have, and hopefully we can share what we have successed: -Sles Linux 11.3 installed, Samba 3.5.4 server configured and started, no DNS or LDAP installed.
-added to smb.conf:
client ntlmv2 auth = yes
wins support = Yes
wins proxy = No
lanman auth = yes
[Code]...
Reboot and now Win7 can join the domain, but with an error message about can't change the domain name to... but I just ignore it, and it works OK with any shared folders, the same way for WinXP. The only problem is that it won't map the logon drive P: but I can apply the "logon.bat" instead. However, I don't understand all of what I have done to make it work as I just copied from other experts.
I have just reinstalled testing on a Samsung Q30 and I cant get X to start. I am just left with a blank screen and ctrl+alt+Fn does nothing. I had a previous install of testing that worked fine but it might have been running a previous version of the kernel, or I had installed a bug fix to do with 915resoultion that I can't remember about. Booting off a Slax live cd works fine but I have had similar problems with Knoppix and Ubuntu.
I am running LXDE but I previously tried Gnome and had the same problem. Running xander displays cant open display Running dpkg-reconfigure xserver-xorg returns nothing, as does Xfree86 -configure There is no /etc/X11/xorg.conf or installed by default, I have tried running startx with a custom xorg.conf and the automatically generated one from -configure. The automatic one did not include any resolutions and was configured for a dual head set up although there was only one monitor connected.
I thought it may be the same problem as this:[url]
But I have tried following the bug fixes on that site and I have had no luck.
lspci
Xorg.0.log
OK... I tried everything i could think of... but i still cannot get my Open SUSE 11.1 to mount my samba share at boot! I still don't understand the 11.1 boot sequence. can NE one help me... tell me what files to give you output from... Ty guys P.S. My shares originate from a Windows Server 2003 RC2 machine, and it's dns server doesn't work correctly... so my mount command is
mount -t //192.168.x.x/files/ /nET/ -o username=linux,password=xxxxxx
please let me know what other info you need... I don't have the internet, so it will be tommorow b4 i see this again!!! Thanks
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies View RelatedI installed samba server on fedora13 last week and share some files from samba server GUI i also created samba user and password for shared folders but I can't get access samba share folder from neither fedora machine nor Windows XP When I open samba share from other fedora such as smb://192.168.10.2 I can see share file and when I browse folder, password required box is appeared but after I put samba username and password the Error message is Unable to mount location Failed to mount Windows share even when I browsed samba share from windows xp error message is \192.168.10.2smbshare is not accessible. you might not persioon to use this network resource. Contact the administrator The network path was not found.
[Code]...
I installed newest Ubuntu system, 11.04, Natty-Narwhal, and PC is running smoothly. It is solid machine, Celeron 430, 1 gb of DDR2 memory and I have both LAN card and graphics integrated on the mobo which is MSI 7529, based on G31/P35/P31 chipset.
I plugged lan cable directly from my PC to the ADSL router. There is another Win Xp machine on the same router and it has connection, and internet is working fine. Right now Im writing from the Win 7 laptop, which is connected to the same router via wifi link... all working like a charm...
But, when I plug the Ubuntu desk I cannot get access to bot lan and internet...
I searched the net and it seems that ubuntu didnt install proper driver during the OS installation. Here are some diagnostics of the current config and state:
Code:
Module Size Used by
binfmt_misc 13213 1
snd_hda_codec_realtek 255820 1
code....
As you can see I need to install driver named r8101 instead this one r8169 and I think it will work that way. I found driver here only problem is dont know how to replace them.
I want to setup a Linux File Server for a small windows network (around 50 users). I do know that I am gona need Smb service/pkg for that. I haven't used Samba for a while now and as per the best of my knowledge, entire communication (including usernames and passwords) between a samba server & windows client machines will be plain text. Is there any way to secure all this communication??
Secondly, if i remember correctly, MS windows wont let me mount more than one samba shares as network disk when all my shares can be accessed by different smb users with different passwords?? is there a solution to this problem? OR may be if there is any other package available for this purpose so that i wont have to use samba?
Recently my computer was infected by several viruses and my brother cleaned it up and installed SuSe for me. He also put windows xp back on my system for our children. I am having a terrible time installing our Dell 924 printer. I have it installed for windows, but cannot get it to print for my Linux system. What am I doing wrong? Can anyone give me some direction?
View 5 Replies View RelatedI have been waiting on installing ubuntu on my mid 2010 MBP 15' for a while now. I was wondering if the dynamic GPU switching was supported yet. Does Ubuntu recognize the intel card and can I use it over the nVidia card?
View 1 Replies View RelatedI have a Broadcom Corporation NetXtreme BCM5721 network card on my server at work.Everything works fine for a few weeks, then randomly the network connection on the server will stop working. After it stops working, I will try to reconnect with the network manager, it shows a wired connection available, it shows the "connection in progress"animation, then the "connection disabled" icon.
I uninstalled the network manager and used manual configuration, but do you think the network manager was the issue? I can't have the server disconnecting randomly every few weeks with no way to know what the real problem is. Was there an issue with the network manager with 10.04?
I know openSUSE (and SUSE Enterprise) work great with windows Active Directory.Now, I understand that Linux systems are far more stable and secure (if configured properly). What about features though? What does openSUSE/Linux have instead of AD for file/folder sharing across the network? Are there roaming profiles? If so, how do I use that?I love openSUSE because of yast (and a few other things). And It's my main LinuxOS on my tower. I am still in college getting my certs and a degree (in networking). I really want to understand why Linux (openSUSE/ SUSE enterprise) is a better networking solution as opposed to Windows Sever 2003/2008.Also, why SUSE over RHEL/CentOS? Yast is awesome, but are there other reasons?
I know that's a lot to ask in one post. Feel free to include links so you won't have to type too much.I'd like both personal opinions, hard facts, and just general user experiences as to the features that make Linux (openSUSE) better, not just the stability and security.
I have installed slacware 13 on an intel server, but the IP add that i have assigned does not work. I used ifconfig to check the ip but it shows me 127.0.0.1. I have run netconfig with the ip address i need and restart the machine, but it goes back to 127.0.0.1
View 2 Replies View RelatedI'm working with 10.10 (Maverick) on an older Compaq laptop. Wireless card is a Cisco Aironet 350. This card is listed as supported and drivers included in the server distro.
During the Network configuration portion of the install, I selected eth1 (wireless); the card came active and a valid network connection was established.
However, after the full server installation the interface (eth1) is not seen.
What's confusing is that modprobe -l shows the drivers as present:
kernel/drivers/net/wireless/airo.ko
kernel/drivers/net/wireless/airo_cs.ko
Insertion and removal of the card is noted in /var/log/messages:
pcmcia_socket pcmcia_socket1 pccard: card ejected from slot 1
pcmcia_socket pcmcia_socket1 pccard: card inserted into slot 1
(I'd be happy to supply more info, but currently set up with Fluxbox and I'll be darned if I can get copy from the xterm to paste into Firefox...)