Ubuntu :: Intel 82567V-2 Network Card Won't Work With 11.04?
Aug 7, 2011
My problem is similar to this one [URL] and I've already tried some of the steps, to no final resolution.The OS in question: Ubuntu 11.04 64 bitProblem hardware: Intel Ethernet 82567V-2 network card[URL]I've already installed the latest driver using the README instructions (sudo make install, etc).The network card will connect ONLY to my Linksys router but not even to my Motorola cable modem, even when it's directly connected to the modem ! I cannot get any web pages at all outside of my LAN, only my Linksys configuration page on my router.As I said above, I've already tried most of the steps in that forum post above. I'm going back to retrace my steps to see what else I can do
View 1 Replies
ADVERTISEMENT
May 18, 2010
I am running Lucid Lynx and have only noticed this problem in the past couple weeks. Before Lucid I ran Jaunty & Karmic on this same box, although I installed Lucid as a clean install. My problem is that up to 5 or 6 times per minute my networking card drops its connection and then has its connection re-established. I have an integrated Intel 82566DC gigabit card on an Intel Motherboard DG35EC connected to a 10/100 network and am running the 64-bit version of Lucid. I've done some considerable searching on this problem and although I've seen many references to similar problems dating back several years, I have found none that seem to have any solutions that do anything for me. I never had this problem under any prior version of Linux on this box (all prior versions were also 64-bit).
In short, this block of messages repeats in my messages log:
May 18 20:18:50 mark-desktop kernel: [10121.062129] e1000e: eth0 NIC Link is Down May 18 20:18:52 mark-desktop kernel: [10122.730873] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX May 18 20:18:52 mark-desktop kernel: [10122.730876] 0000:00:19.0: eth0: 10/100 speed: disabling TSO
Most of the time I don't even see that the connection has gone down. Sonetimes everything seems to be operating fine for a half-hour or more, although it could be dropping out and coming back really quickly all of the time. Sometimes it goes out for 10 seconds.Sometimes it goes out for many minutes and I can get networking back by killing disabling networking and then re-enabling it. It's quite annoying.
I'm sorry if I'm duplicating an existing issue on this forum, but I can't find this exact problem anywhere. Does anyone have any clever ideas about how to fix this?
View 5 Replies
View Related
Apr 25, 2010
I'm having trouble getting X to work after switching from onboard intel video to a 5000 series ATI card. Apparently I need to switch to a MESA or fglrx driver. I did a sudo apt-get install fglrx-driver and it installed but still no X. I'm currently using Karmic. I've tried to boot with a live CD which works fine and changed the xorg file manual but that was a mess.
When I start I get a checking battery state ... done and it stays there forever sometimes and sometimes I can login but without x. Typing startx gives me a long list that says check the xorg website. I've been looking around for a way to fix this and haven't been able to get it working.
View 6 Replies
View Related
Dec 23, 2010
i have an Acer aspire 4920 laptop with opensuse11.3 installed and wifi card has identified home wifi, but for some reason when i enter the wpa-psk key it doesnt connect.i have been at this problem for several days and scanning the net for answers, without joy.i dont know about the command or terminal line, i have tried to type in commands but i get no joy.
View 4 Replies
View Related
Sep 10, 2010
NIC: Intel 82574L Gigabit mobo network card
Issue: After the server has been up for a random amount of time, the network connection is lost. Attaching a console and looking at ifconfig I see a large number of dropped packets and collisions.
use;
Code:
lspci -vxx
to list the make manufacture of NIC and the device driver it is using.
In this case: Intel 82574L, e1000e
Look in var/log/messages to get the version of the driver, in this case 1.0.2
Download .gz file with source code, follow instructions to install newest driver (e1000e.ko), in my case version 1.2.10. [URL]
View 2 Replies
View Related
Jul 20, 2010
I bought a Mini ITX motherboard Intel DH57JG bu the installation DEBIAN does not recognize the ethernet card.
View 9 Replies
View Related
Mar 31, 2010
Intel 1000GT gigabit Network Card itself installed successfully and shows up under network cards. However, when I plug it into the network in place of the regular 100mbit card, it won't show up.
View 8 Replies
View Related
Jan 26, 2010
I just did a dual boot with OpenSuSE 11.2 and Windows 7. They both work perfect but for some reason the wireless (intel wifi 5100 AGN) and my wired network card (Atheros AR8131 Gigabyte controller)do not work in opensuse. Now the problem is that I do not have a clue about linux and therefore I don't know how to fix the problem. I searched the forum and I tried these commands "sudo /sbin/ifdown eth0" and "sudo /sbin/ifup wlan0" and both says something like device not connected/present (can't remeber exactly).
View 9 Replies
View Related
Apr 8, 2010
I clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies
View Related
Sep 16, 2010
I have been waiting on installing ubuntu on my mid 2010 MBP 15' for a while now. I was wondering if the dynamic GPU switching was supported yet. Does Ubuntu recognize the intel card and can I use it over the nVidia card?
View 1 Replies
View Related
Aug 20, 2010
I have just set up a server with Ubuntu Server edition 10.04. I installed it by plugging the harddrive into my main pc as the server doesn't have a cd drive. Now the drive is back in the server and the internet won't work. I have run lspci and lshw and neither show a lan or network card anywhere. ifconfig comes up with nothing related to eth0, and says the 'inet addr' is 127.0.0.1. My motherboard has an onboard Realtek 8101L LAN controller. Can't seem to find much with a google search
View 2 Replies
View Related
Feb 13, 2010
In new Acer Extensa 5635G i install 11.2 but lan card don`t work,wireles too!Hеrе info
Code:
/sbin/lspci
07:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
09:00.0 Ethernet controller: Attansic Technology Corp. Device 1063 (rev c0)
/usr/sbin/hwinfo
[Code]..
View 5 Replies
View Related
Jun 26, 2010
I'm trying to activate a wireless network on an ubuntu server 10.04. The machine has a TPLink PCI wireless card. Card is well recognized, and scanning for wireless connection it finds correctly the essid of the access point in the room. But when I try:
Code:
$ sudo iwconfig wlan0 essid "apoint" key s:my_key_8
this error is returned:
Code:
Error for wireless request "Set Encode" (8B2A) :
SET failed on device wlan0 ; Invalid argument.I looked for similar situations over many forums, and I found that it could be the card doesn't support the encryption type (My AP uses WPA with TKIP). However if I use an ubuntu desktop live CD on the same machine, I can connect witouth any problem with NetworkManager 0.8.
View 2 Replies
View Related
Jul 18, 2010
I swited network cards because the card i was using wouldn'tlip, and the cable kept falling out. Now, the internet doesn't work. They're Both Dlink cards, but they might be diffrent models. The lights on the card are on, but I'm not gettin internet. Is their any command I can use to automatically reconfigure the network/card
View 3 Replies
View Related
Jan 6, 2010
I've been using Slackware distribution for few years now, Setup new system with Xen Server 5.5 and installed Slackware 13 on it, but network card is not detected and can't seem to make it work.
View 4 Replies
View Related
Oct 2, 2010
I can't get wake up on lan (wol) to work on my network card.The strange thing is that before I had it working with the exact same hardware. But I was on Centos 5.4 then. Now I am on Centos 5.5.Am I correct in concluding that the sky2 driver does not support wake up on lan?
View 4 Replies
View Related
Dec 14, 2010
a machine with 2+ network cards, need to setup TFTP server on one card and use internet on another.
the tftpd server works on default routing network adaptor with following configuration.
How set the TFTP server on the secondary network adaptor?
TFTP server tftpd by xinetd configuration in: /etc/xinetd.d/tftp
{
protocol = udp
port = 69
socket_type = dgram
[Code]....
Could not find how to change the post <prefix> I remembered clearly I did before.
View 1 Replies
View Related
Mar 14, 2009
Wireless card detected but cannot connect to a wireless network
I have install it suse 11, and everything went well until the wireless thing is not working, my card is Broadcom BCM4318, I see my card on the network settings but I cannot configure the card, and also I cannot connect to a wireless network, can someone tell me what to do here, I am loosing my patient....
View 4 Replies
View Related
May 8, 2010
i installed suse (KDE) on my old notebook and now I'm trying to get the wlan to connect to our router and can't figure out how to get it to work. My card seems to work, the network manager even finds the router, but i just cant get a connection. I followed the steps of the "Getting Your Wireless to Work" thread and these are the results:
[Code]....
- i messed around a bit with the network settings and might have cluelessly broken something (or broken it more)
- i tried a usb-wlan-card as an alternative, which didn't work either, but could possibly have messed things up even more.
View 7 Replies
View Related
May 1, 2009
I just have CentOS installed and cannot get the Agere et131x network card to work.I have tried the following:Reboot the computer and still did not see the network hardware.
Fai
lspci
Quote:
[code]....
View 7 Replies
View Related
May 2, 2010
I am running Ubuntu 10.04 with an Intel 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller, and no sound output. I have both pulseaudio and ALSA installed. I have already checked with
Code:
alsamixer
that my sound isnt muted and aplay -l outputs this
Code:
xxxx@xxxx-ubuntu:~$ aplay -l
[Code]...
View 4 Replies
View Related
Aug 21, 2010
I'm running Ubuntu 10.04 Server. I can't get my Wireless Card & Wired Card to work at the same time. My interfaces file is incorrect, when I comment out 1 of the interfaces the other works. I have attached my interfaces file.
View 2 Replies
View Related
Mar 21, 2010
How do I know if my intel chipset graphics card thing is installed?.
View 1 Replies
View Related
Apr 30, 2010
Lucid has been good to be so far, except for the fact that my screen flickers occasionally (I'd say once or twice every 30 minutes) I'm using an ASUS laptop with an INTEL GMA 4500MHD (It's this laptop. I read a bug report about the xserver-xorg-video-intel, but the issue was much more severe and marked as solved before Lucid was released.
View 7 Replies
View Related
Aug 22, 2010
i just install ubuntu 10.4 linux 32.bit on my Pc and it's was running fine beside the video card (intel x4500 ) not supported in ubuntu anyway after i update about 251 package in ubuntu ,i restarted the pc after in the grub ...they show me 4 Ubuntu ! 2 for boot ubuntu and 2 for ubuntu recovery and 1 for windows 7 loader !
View 3 Replies
View Related
Oct 21, 2010
Just spent about 4 hours upgrading from 9.10 to 10.04 thinking it would fix my graphics problems. Basically I have no 3d acceleration of any kind, is there any way i can load the intel drivers? Because what I'm using now is really crappy.
[code]...
Can i just change something in my xorg to intel and it will load that driver ? I've tried the "hardware drivers" thing but it does not show anything.
View 1 Replies
View Related
Nov 5, 2009
Just installed Karmic Koala on my Intel Macbook via Virtualbox and cannot get wireless working. Previously did this with 9.04 and everything worked. Do I need to use ndiswrapper? I don't remember having to do that before.
View 8 Replies
View Related
Jan 4, 2011
I have an IBM X3250 M3 server were Iam trying to install Fedora 9 version on RAID 1 and am unable to configure it. Some body guide me with LAN card driver for Inetl 8000 series Gigabit NIC card driver for fedora 9.
View 1 Replies
View Related
Feb 2, 2010
I have a Dell Vostro 200 with the above wireless card in it and I cant get it to work. I have been on Intel's website and downloaded e1000-8.0.18 and installed as the instructions. But it is still greyed out on the Network Manager. I have just installed Ubuntu Desktop the latest current version.
View 1 Replies
View Related
Jul 25, 2010
I have an old Toshiba Satellite A30 Notepad. I've installed Ubuntu 10.04 onto it and everything but WiFi works. I've installed wicd and several other network tools but just can't get Ubuntu to let me use the WiFi connection (the option is greyed out).I know the card works because the last OS (Windows XP) used it without any problems. The card is detected, the drivers are installed and the hardware (slider) switch is set to on.I think the issue is related to the Radio Frequency Kill Switch being on but I don't know how to turn it off.The output from various commands are:
sudo lshw -C network is:
Code:
*-network:0
description: Ethernet interface[code]............
View 9 Replies
View Related
